y0551 HT Car Bag for 1/6 scale cars (Fits FG, Smartech/Carson a.s.o.)

Genuine ATOP spare/option part. CNC-machined from 6061 aluminum, significantly stronger and more rigid than any plastic version. Doule-sided anodized aluminum servo horn, available in 15T and 18t spline version. Three smooth 2.5 mm holes per side. 15T fits:Savöx 0236 MGSavöx 0235Losi 900and many other servos with 15T spline shaft18T fits:Spektrum DBXL-servo SPMS901Contents:1 piece

The new TT0900 electric starter is pre-assembled and fits a wide range of models including the Losi 5ive-T, 5ive Mini and DBXL, most FG models, HPI-Baja / Wild Attack series etc. The TT0900 electric starter can be started with the remote control (free channel required!). The new TT0900electric starter has much more power than the previous Electric starter thanks to the brushless motor and higher voltage. The popular Zenoah G320 is no longer a problem. It also no longer uses a one-way bearing, which clearly increases reliability. Also the installation space has been noticeably reduced by the motor and a planetary gearbox.The starter components to be fitted weigh about 666 grams plus the battery.For mounting the starter, the flywheel on the engine is replaced by the version with spring-loaded pawls included in the delivery. The tools required for this, piston stopper and flywheel puller, are also included in the delivery.For the 3rd channel the transmitter should have a switch with two positions (momentary switch preferred) or a controller. An additional channel is required for a remote engine killswitch. A killswitch is included in the scope of delivery, but a real fail-safe module such as TT0990 offers higher safety. A possibly already existing failsafe module can also be used.Due to the splitting of the functions engine start and engine stop on two channels, no more compatibility problems with different remote controls are to be expected, only the availability of free channels matters.A 3S LiPo battery is required as the power source.In the shops options menu, we offer a special battery with a more compact design (5,600 mAh/30C, 110 x 49 x 34 mm) which makes installation usually easier in many cars, as well as a battery with standard dimensions (3,900 mAh/60C, 135 x 45 x 25 mm). Of course, other 3S batteries can also be used at your own discretion, but the load capacity (capacity x C-rate) should be on a similar or higher level.Please note that we cannot ship batteries to countries outside the European Union!Since the starter unit can be mounted vertically or horizontally and the brushless starter motor is very small, almost all air filters and most tuned pipe systems can be used.Notes regarding necessary modifications known to us for mounting the starter depending on the vehicle: FG 4wd onroad Rear r/h plastic body mount, depending on position, slightly modified or relocated FG 2wd onroad horizontal engine No modifications Mecatech FW01 No modifications FG 4wd Buggy sportsline Depending on the body shell, minor trimming is required. FG 2wd Buggy current chassis Depending on the body shell, minor trimming is required. FG 2wd Marder (old chassis) Starter fits without modifications to the chassis plate. However, the body shell has to be cut out a bit more seriously in the area of the starter. A repositioning of the rear r/h body mount is recommended. FG Monster Cut the r/h side panel slightly and add a flat area to the aluminum tube which supports the panel on the engine Losi 5ive-B Depending on the tuned pipe, mount starter with motor on top or on the l/h side. Losi 5ive-B Mount the starter motor on the l/h side, space for the tuned pipe is very tight and must be tested in each individual case. No problems when using the stock muffler box. Losi DBXL Depending on the tuned pipe, mount starter with motor on top or on the l/h side. If the starter motor is to be mounted on the side, one screw of the motor roll cage must be replaced by a CSH screw. Carson C5 Only with Zenoah or CY engine, not with Smartech PT engine (different hole pattern on engine)! Carson C6 With the C6, depending on the body shell, trimming is required. HPI 5B/T Depending on the body shell, minor trimming is required. Carson Wild GP Attack Depending on the body shell, minor trimming is required. The accommodation of the engine killswitch, controller unit and wiring harness must be carried out at your own discretion. User Manual FG 4WD On-Road FG Monster FG 2WD On-Road horizontal engine FG 2WD/4WD Buggy current chassis Losi 5ive-T Losi DBXL FG 2WD Marder (old chassis)

Genuine HT spare/option part. Aluminum engine mount for Losi DBXL with reinforced threads due to separate threaded inserts. The steel inserts are set with thread locking compound and feature a flange on the top side for an absolute secure fit.A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.The original screws can be re-used.Contents:1 piece

To ensure the required cooling for current 1/5 and 1/6 engines the flywheels have fins on both sides. Therefore the fan housing has large openings on the crankcase side for the required air supply. However, the risk of foreign objects (grass, sand, or even stones!) entering here Is very high! As a result, broken fins on the flywheel occur frequently. This leads to reduced cooling efficiency and - even more critical vibrations from a flywheel which is out of balance due to missing fins. Therefore, this kind of flywheel protection is highly recommended, especially for offroad use. The product video explains the handling in detail! Note:It is essential to thoroughly clean and degrease the crankcase prior to attaching the hook-and-loop tape (OKS2661)!For installation on Chung-Yang and Zenoah engines in FG cars, the crankcase cover must be slightly modified in two places where the engine mount is attached (see Figure 6 and 7). Furthermore the fit of the fabric must be as tight as possible in the region of the layshaft pinion (in front of the differential ring gear!) (see Figure 8).Set includes:Special tailored fabric with sewed on hook-and-loop tapehook-and-loop tape for installation to the crankcaseAdhesive for securing the hook-and-loop tape

Genuine ATOP spare/option part. CNC-machined from 6061 aluminum, significantly stronger and more rigid than any plastic version. Doule-sided anodized aluminum servo horn with 15T spline. Three M4 threaded holes per side. Fits:Savöx 0236 MGSavöx 0235Losi 900and many other servos with 15T / 8mm spline shaftContents:1 piece

Genuine HT spare/option part. Ball & socket tool with t-handle, special version for the ball joints.Fits Losi 5ive-T. 5ive-B, Desert Buggy XL, Desert Buggy XL-E, Monster Truck XL and the HPI Baja 5B and Baja 5R Ford Mustang.Contents:1 piece

Spare part for AREA-XL 013 Ball bearing mounted servo saver and steering rod for Losi Desert XL.Content:2 pieces

Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces

Genuine Losi spare/option part. Contents:4 pieces

Complete set of 22 sealed ball bearings for Losi DBXL-E 2.0 and Desert Buggy XL 1/5.Set includes:16 pieces of 12 x 24 x 6 mm sealed bearings (axle shafts / differentials / clutch bell)4 pieces of 10 x 22 x 6 sealed bearings (bevel pinion shafts)2 pieces of 8 x 19 x 6 sealed bearings (intermediate shaft)Total: 22 sealed bearingsPrice when bought separately: 95.92 EUR

Genuine HT spare/option part. This machined aluminum servo adapter allows easy installation of servos with a 69 x 18 mm mounting bolt pattern (for example Orange-Power, S8203) in vehicles / radio plates which provide a 75 x 18 mm mounting bolt pattern (for example Losi 5ive-T, Mini WRC, HPI Baja 5 series cars, many FG cars).The use of this adapter servo will neither tilt the servo, nor does it change installation height. Scope of delivery:1 x Servo mount adapter2 x Socket head cap screws 3 x 20 mm2 x Socket head cap screws 3 x 12 mm2 x Shim ring 3,2 mmContents:1 piece

Genuine ATOP spare/option part. CNC-machined from 6061 aluminum, significantly stronger and more rigid than any plastic version. Single-sided anodized aluminum servo horn, available in 18t spline version. Three M4 tapped holes for the linkage. 18T fits:Spektrum DBXL-servo SPMS901Contents:1 piece

To celebrate the 30th anniversary of the legendary Marder 1/6 scale 2WD buggy, FG Modellsport/T2M releases a special edition, limited to 300 numbered pieces, with the original signature of Franz Gröschl on the sticker sheet as well as a top equipment (G260RC Zenoah engine, hi-capacity low friction aluminum shock absorbers and special aluminum engine mounts). with original 260 Zenoah with Low-Friction Alu shocks with alloy enginemount The Models is built on a 4 mm u-bended chassis. All borings of the lower side are countersunk, therefore the screw heads can't bear out.Double wishbones at font and rear axle as well as 4 bulk oil-pressure shock absorbers guarantee perfect ground adherence. All rotating parts are supported by ball-bearings. Rear gear wheels, differential gears and all driving elements are case-hardened. The side guards protect the model from dirt. With original signature of Franz Gröschl. The model is equipped with a powerfull 26 ccm engine which runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 liters enables you to drive about 45 minutes. The engine can be started without difficulties through the integrated pull-start. To complete the models all merchantable servos and radio control systems are suitable.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery

Hobbythek car bag for 1/5 carsFits for all 1/5 models for example: FG-: HPI-; Mecatech FW01-; Carson-; Smartech-; Conrads-; Harm-; RS5-; Lauterbacher a.s.oMade from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure.No dirt in the car boot!Dimensions:Length: 95 cmWidth: 40 cmHeight: 30 cm

The XXL version is especially made for the Losi 5ive-T, Mini 5ive WRC, Desert Buggy XL; Arrma Outcast/Kraton; Axial Honcho, Traxxas X-Max/XRT; UFRC GR1/Big Bully. Of course, other 1/5 and 1/6 large scale cars will fit into this bag as well; however, in this case the XXL bag gives you plenty of room for additional accessories. Made from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure. No dirt in the car boot! Dimensions: Length: 100 cmWidth: 57 cmHeight: 39 cm

Incl. 2x TopTuning 3S 3100mAhFor those who want the biggest, baddest RC rock crawler ever, the legendary Axial® Honcho is now available on the 1/6 scale SCX6 4WD platform. With its 2-speed transmission and powerful Spektrum Smart electronics, this massive RTR is an absolute beast! Key Features Based on the legendary Axial® Honcho New vehicle option on the SCX6 platform Increased performance due to body design Two-speed metal gear transmission Spektrum Smart 3-channel radio and electronics The 1/6 scale Axial® SCX6 platform has taken RC rock crawling into a whole new dimension, armed with a huge amount of detail and high-performance functionality. Now, Axial has expanded the SCX6 lineup with an exciting 1/6 scale version of the insanely popular Honcho. Whether you're a fan of the original SCX10 Honcho, a rock crawling enthusiast, a large-scale aficionado, or all of the above, the Axial SCX6 Honcho 4WD RTR is sure to please. It's the biggest, baddest RC rock crawler ever!The SCX6 Honcho is engineered for extreme durability and performance, as shown by its AR90 axles with metal ring and pinion gears and front offset pumpkin. For optimal handling, the chassis has a three-link front and four-link rear suspension setup and metal links are used at all suspension points. The transmission offers high and low gears out of the box, with a Spektrum S614 metal gear high-torque servo included and installed for the two-speed linkage.Molded from high traction compound with an aggressive tread pattern, the massive, 7" tall, officially licensed Falken Wildpeak M/T tires provide excellent grip and ground clearance over dirt, rocks, and all other off-road surfaces. They're mounted on officially licensed Black Rhino Primm beadlock wheels for easy removal and replacement without gluing.With the included Spektrum DX3 radio, you'll enjoy the superior range, response, and interference resistance of exclusive DSMR® technology. Together with the installed Firma Crawler 120A Smart Sensored-Brushless ESC, it also comes ready to deliver the telemetry advantages of exclusive Spektrum Smart technology. Install a Spektrum Smart LiPo battery and you can view vehicle battery capacity on the transmitter's voltage level indicator. Outfit the DX3 with the optional BT2000 Bluetooth module, download the free Spektrum Dashboard app to your smart device, and you're ready to use more real-time Smart telemetry without needing on-board sensors or modules.Measuring over 2-1/2 feet long and topped off with a modernized Honcho body, the Axial SCX6 Honcho 4WD RTR is the rig that will take your rock crawling and climbing adventures to an exciting new level. Just add your choice of suitable battery and aim for the top! Features 1/6 scale chassis design is based on the proven SCX10 III Metal gear transmission comes configured for two speeds with high and low gears Durable three-link front and four-link rear suspension provides optimal handling AR90 axles feature metal ring and pinion gears Replica V8 engine cover adds to the realistic appearance Spektrum DX3 2.4GHz DSMR® radio provides superior range, response, and interference resistance and is compatible with Smart technology Spektrum Firma 120A Smart Brushless Crawler ESC feeds telemetry data to the DX3 transmitter in real time Includes a powerful Spektrum S905 high-torque, large scale steering servo (also accepts larger 1/5 scale servos with the included adapter) Modernized Honcho body with rear tube cage includes interior detail High-traction, 7" tall, officially licensed Falken Wildpeak M/T tires are mounted on officially licensed Primm Black Rhino beadlock wheels SCX10 III Based Chassis DesignInspired by the proven SCX10 III, the SCX6 platform follows a similar design while increasing the size to meet large scale needs and expectations. 2-Speed Metal Gear TransmissionOut of the box, the SCX6 Honcho 4WD RTR is configured for two speeds with high and low gears. A Spektrum S614 Metal Gear High-Torque Servo is included for the two-speed linkage. This feature provides a true crawling gear ratio while also allowing you to shift for more speed. AR90 AxlesThe AR90 axles feature metal ring and pinion gears with a front offset pumpkin. The 3-piece front axle accommodates optional aluminum carriers and steering knuckles. "Hi-steer" steering knuckles raise the steering tie rod for increased ground clearance. The rear axle can be set up for optional rear steering. Replica V8 Engine CoverThe molded engine cover captures the look of a modern V8 engine. It not only enhances the scale realism but also serves as the ESC mount and receiver box cover. 3-Link Front/4-Link Rear Suspension The SCX6 suspension geometry matches the SCX10 III with metal links used at all suspension points for durability. 1/6 Scale Steering ServoSteering is controlled by a Spektrum S905 high-torque, large scale servo. The servo mounting location will also accept an optional 1/5 scale servo if you choose to modify your rig. Spektrum Sensored Brushless Rock Crawling ESCIncluded and installed, the Spektrum Firma 120A Smart Brushless Crawler ESC provides throttle input to the massive Firma 1200Kv Sensored Brushless Motor. The motor itself weighs in at 1.75lb (.780kg) and gives this beast enormous power and realism! Officially Licensed Falken Wildpeak M/T TiresThe 7" tall, officially licensed Falken Wildpeak M/T tires are molded from a high traction compound and feature an aggressive tread pattern. They provide excellent grip and ground clearance over dirt, rocks, and other off-road surfaces for nonstop climbing and crawling. Officially Licensed Black Rhino Primm Beadlock WheelsThe SCX6 Honcho crawler's officially licensed Black Rhino Primm beadlock wheels add realism and allow easy tire removal and replacement without gluing. In The Box (1) 1/6 SCX6 Honcho 4WD RTR (1) Spektrum DX3 Smart DSMR® 3-Channel Radio with SR515 receiver (1) Spektrum Firma 120A Brushless Smart Crawler ESC (1) Spektrum Firma 1200Kv Sensored Brushless Crawler Motor (1) Spektrum S905 High-Torque 1/6 Scale Steering Servo (1) Product Manual (4) AA Transmitter Batteries

Genuine Top Tuning spare/option part. Dimensions:Length: 420 mmWidth: 20 mmContents:2 pieces

This two-piece differential cover is easy to attach with the existing screws and provides optimal protection against stones and dirt. Suitable for all 2WD FG Offroad models, not suitable for the 2WD models that are based on 4WD e.g. Fun Cross, Leopard, Truggy and all WB535 models.Also suitable for Carson 2WD models e.g. Uno, Attack, Gas Blaster and more.Contents:1 set

Genuine Losi spare/option part. Contrary to the Losi 5ive-T 2.0 ready-to-bind model the 5ive-T roller comes without rc-components (servos / receiver) and without engine / clutch / muffler / air filter.The Roller's body shell is also available in the painted versions for an additional surcharge!Contents:1 piece