y1350 Aluminum engine mount for Losi DBXL, reinforced version
€14.90
% €34.90 (57% saved)
Available
Product information "y1350 Aluminum engine mount for Losi DBXL, reinforced version"
Aluminum engine mount for Losi DBXL with reinforced threads due to separate threaded inserts. The steel inserts are set with thread locking compound and feature a flange on the top side for an absolute secure fit.
A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.
The original screws can be re-used.
Contents:
- 1 piece
Login
Customers also bought
With the Futaba R404SBS, Futaba offers the fastest and most compact receiver for RC cars and boats on the market today! The R404SBS has the ultra-fast signal transmission F-4G (10 channels with telemetry at maximum transmission speed). This makes the model's response even more direct while maintaining maximum transmission reliability!The new F-4G (Futaba 4th Generation System) transmission mode supports the familiar SR mode and has an even higher transmission speed than the previous T-FHSS SR. At the same time, the size of the new F-4G receivers R404SBS / R404SBS-E could be reduced again. To make this possible, the R404SBS-E has a large, upward-pointing antenna to optimize signal reception. Due to the chosen design, the footprint of the receiver remains unchanged.To take full advantage of the speed of Futaba's F-4G SR technology, there are numerous FUTABA SV servos that can also be converted to SR mode. The following servos are currently SR compatible: BLS371SV, BLS471SV, BLS571SV, BLS671SV, BLS671SVi, BLS373SV, S9372SV, S9373SV, HPS CB700, HPS CT700, HPS CB500, HPS CT500.The R404SBS has antenna diversity. The receiver constantly compares which antenna has the better signal and switches to it in a flash. The R404SBS has the second antenna in the housing.S.BUS2 sensors can be connected to the S.BUS2 port. They transmit up to 32 telemetry data sets. The receiver has an integrated telemetry transmitter that transmits the data to the transmitter. This allows the measured values to be displayed or acoustically output at the transmitter.ATTENTION: The receiver supports HV (High Voltage) and can be powered directly from a 2s LiPo battery. Always make sure that the connected servos are also designed for HV! Technical specifications Transmission type: F-4G Frequency range: 2.4 GHz Channels: 4 PWM / 10 S.BUS Transmission power: 100 mW EIRP S.BUS Port: S.BUS2 Voltage range: 3.7-8.4V Dimensions: 25.5 x 20 x 10.6mm Weight: 5.7g Features 4/10 channel F-4G receiver 10 channels of telemetry at maximum transmission speed SR mode compatible Telemetry with S.BUS2 Telemetry with 32 channels S.BUS2 port Hi-Voltage (HV) Antenna diversity
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum chassis braces, for Losi DBXL 2.0.Compared to the stock plastic parts (from sets # LOS251115 and LOS251116) the higher strength of the aluminum parts noticeably increases the chassis rigidity.Contents:1 piece
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum front top chassis brace; fits Losi DBXL 2.0.Stiffer than the stock plastic part (from set # LOS251115), the aluminum brace reduces chassis tweak in the area of the steering assy.Contents:1 piece
Genuine HT spare/option part. Gas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.Contents:1 piece
Customers also viewed
y0550 HT Car Bag for 1/5 scale cars (Fits FG, HPI, Mecatech FW01, Smartech/Carson a.s.o.)Fits for all 1/5 models for example: FG-: HPI-; Mecatech FW01-; Carson-; Smartech-; Conrads-; Harm-; RS5-; Lauterbacher a.s.oMade from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure.No dirt in the car boot!Dimensions:Length: 95 cmWidth: 50 cmHeight: 30 cmy0551 HT Car Bag for 1/6 scale cars (Fits FG, Smartech/Carson a.s.o.)Fits for all 1/6 models for example: FG Offroad-; Monster/Stadium-; Racetruck-; Carson-; Smartech-; Reely Carbon Fighter; Losi Super Rock Rey, Super Baja Rey, Axial Jeep and any more models. Made from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure. No dirt in the car boot! Dimensions: Length: 70 cm Width: 50 cm Height: 40 cm y0558 HT Car Bag XXL for LOSI 5ive-T, Mini 5ive WRC and Desert Buggy XL and many moreThe XXL version is especially made for the Losi 5ive-T, Mini 5ive WRC, Desert Buggy XL; Arrma Outcast/Kraton; Axial Honcho, Traxxas X-Max/XRT; UFRC GR1/Big Bully. Of course, other 1/5 and 1/6 large scale cars will fit into this bag as well; however, in this case the XXL bag gives you plenty of room for additional accessories. Made from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure. No dirt in the car boot! Dimensions: Length: 100 cm Width: 57 cm Height: 39 cm
The Basic Kit is particularly intended for persons switching and differs from the Evo 2020 by not including the following parts: Engine Tuned pipe Body shell Rear wing Wheels Innovations of the, according to the manufacturer FG, the race model EVO 2020 to be expected in September 2020 Competition-OnRoad RC car with the latest technical developments. Latest version Improved - in numerous details! Unique among the large scale models. New stabilizer bar construction front and rear. Ball stabiliszers or frame stabilizers can be used (accessories). 10 mm thick chassis made of T7075 aluminium with cut-outs for weights (also under the tank) and grooves in the front area. This allows the vehicle to be perfectly adapted to the track or the driver. The engine is now again bolted to the chassis for more stiffness. Optimally designed wishbones on front and rear suspension. Reinforced and with toe-in adjustability, which is performed via aluminum wedges. Front upper wishbone for more adjustment possibilities. All gears with fine pitch.Since 1997, i.e. since the beginning of the 1:5 RC car scene, FG Modellsport has been represented with team drivers worldwide at national and international competitions. With the Competition-EVO series, FG won most world championships and almost all European championships. Content10 mm T7075 aluminum chassis plateAir filter / AirboxFront and rear hydraulic brakesDifferentialLarge volume shock absorbers, black anodized
Genuine Losi spare/option part. Contents:1 piece
Original TopTuning spare/option part. Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT-Smartech/Carson engines.Fits all Walbro 603/813/990/771/527/1107 carburetors as well as all Smartech/Carson PT engine carburetors and many more!The TopTuning carburetor heat sink counteracts the notorious vapor lock at high engine temperatures.In fact all current large scale engines have a special adaptor for the thermal insulation of the carb (isolator) to keep the carb as cool as possible, so that the fuel does not form bubbles due to heat transfer from the cylinder. And without this isolator the gasoline would literally cook after a short operating time and therefore the engine would receive a leaner mixture. The much feared lean-out until the engine stalls is inevitably.Unfortunately, even a special isolator is often insufficient at higher ambient temperatures or when the engine is subjected to higher loads, e.g. in racing. In such scenarios the better heat dissipation of the Top Tuning carburetor heat sink contributes to the solution of the problem.The easy to install heat sink, requires a considerable manufacturing and milling effort and fits easily to all common 1:5/1:6 large scale cars, such as FG, Mecatech, Smartech/Carson, HPI, Losi, etc..For installation in FG 4WD cars the rear cross member # 66212 must be modified.Attention: the Allen head screw is an imperial size and therefore not compatible with metric Allen wrenches! Available in our options menu Content: Carburetor heat sink 1 x Allen head screw #8-32 x 5/8" (for Walbro carbs) 1 x washer 4 mm
Genuine Losi spare/option part.Contents:2 pieces
Genuine Smartech spare/option part.Content:2 piece