Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

AT-DBXL005 ATOP aluminum steering servo horn 15T, double-sided for Losi DBXL/DBXL-E

Product information "AT-DBXL005 ATOP aluminum steering servo horn 15T, double-sided for Losi DBXL/DBXL-E"

Genuine ATOP spare/option part.

CNC-machined from 6061 aluminum, significantly stronger and more rigid than any plastic version.

Doule-sided anodized aluminum servo horn with 15T spline. Three M4 threaded holes per side.

Fits:
  • Savöx 0236 MG
  • Savöx 0235
  • Losi 900
  • and many other servos with 15T / 8mm spline shaft


Contents:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

Average rating of 0 out of 5 stars

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€47.90*

Average rating of 0 out of 5 stars

y19302/02 Piston Blocker for almost all engines
Genuine HT spare/option part. Helpful tool for removal of clutch shoes, flywheels and many more.FitsZenoah G230/G240/G260/G270/G290/G320Chung-Yang enginesPT enginesLosi enginesHPI enginesThreadsize:M10 x 1Contents:1 piece

€9.90*

Average rating of 0 out of 5 stars

y0811 After-Run, performance enhancing preservation for all 1/5 and 1/6th scale models, 20 ml
Genuine HT spare/option part. After-Run is a performance enhancing preservation, which ensures that the engine starts properly, even after a long time (winter break) storage. Added to the fuel it keeps the fuel system clean.Among other After-Run conserves the diaphragm of the Walbro carburetor!For long term storage (i.e. during winter!) "vital" for the carburetor diaphragms!For 23 to 32 cm³ engines like Zenoah, Chung Yang, PT, Losi, HPI a.s.o.It binds water in the fuel, particularly important when the engine is not run regularly or after wet races. After-Run improves engine performance, ensures better combustion, removes debris and residues. Simply add the content of the bottle to 5 litres of fuel.Contents:1 piece / 20 ml

Content: 20 Milliliter (€395.00* / 1000 Milliliter)

€7.90*

Average rating of 0 out of 5 stars

y19302/01 Flywheel and Clutch puller CY, Zenoah, HPI, Losi
Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece

€17.90*

Average rating of 0 out of 5 stars

GPM Starter cover, no. BJPSCO
Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.

€25.60*

Average rating of 0 out of 5 stars

y1013 Motul Air filter oil for foam filters
Genuine Motul spare/option part. High-cling oil for foam cartridge air filters, especially for offroad and street use. The oil reinforces the the air filter'e efficiency and retains dirt, mud and sand particles, which will greatly extend the life of the engine. The blue tint makes it easier to control even oil application to the filter.Apply oil to filter generously and work the foam vigorously by hand to ensure complete oil penetration. Press foam slightly to remove excessive oil when done.Contents:1 piece / 400 ml

Content: 400 Milliliter (€47.25* / 1000 Milliliter)

€18.90*

Similar products

Average rating of 0 out of 5 stars

AT-DBXL012 ATOP Alloy engine mount for Losi Desert XL+MTXL
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum engine mount for Losi DBXL+MTXL. A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.Contents:1 piece This article is identical to the article in the video!

€22.90*

Average rating of 0 out of 5 stars

AT-DBXL003 ATOP aluminum throttle/brake servo horn for Losi DBXL/DBXL-E
at_dbxl003 Version: AT-DBXL003-01 with 15 teeth
Genuine ATOP spare/option part. CNC-machined from 6061 aluminum, significantly stronger and more rigid than any plastic version. Doule-sided anodized aluminum servo horn, available in 15T and 18t spline version. Three smooth 2.5 mm holes per side. 15T fits:Savöx 0236 MGSavöx 0235Losi 900and many other servos with 15T spline shaft18T fits:Spektrum DBXL-servo SPMS901Contents:1 piece

€14.90*

Average rating of 0 out of 5 stars

AT-DBXL014 ATOP Layshaft bearing flange for Losi Desert XL+MTXL
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum intermediate transmission shaft bracket for Losi DBXL. The high strength of the material and the larger screws provide a secure seat for the bearings and add torsional rigidity.The set includes lager bearings (8 x 22 x 7) for higher load capacity and mounting bolts.Contents:1 piece This article is identical to the article in the video!

€28.90*

Average rating of 0 out of 5 stars

AT-DBXL004/02 ATOP aluminum steering servo horn for Losi DBXL/DBXL-E 18 teeth
Genuine ATOP spare/option part. CNC-machined from 6061 aluminum, significantly stronger and more rigid than any plastic version. Single-sided anodized aluminum servo horn, available in 18t spline version. Three M4 tapped holes for the linkage. 18T fits:Spektrum DBXL-servo SPMS901Contents:1 piece

€14.90*

Average rating of 0 out of 5 stars

AREA-XL 017/04 Spare pins
Spare part for AREA-XL 017/02 Center differential tower with tuning brake system for Losi Desert XL.Content:4 pieces Montage video:

€5.90*

Average rating of 0 out of 5 stars

AREA-XL 017/05 Spare brake pad return springs
Spare part for AREA-XL 017/02 Center differential tower with tuning brake system for Losi Desert XL.Content:4 pieces Montage video:

€8.90*

Average rating of 0 out of 5 stars

AREA-XL 013/02E Spare turnbuckle
Spare part for AREA-XL 013 Ball bearing mounted servo saver and steering rod for Losi Desert XL.Content:2 pieces

€9.90*

Average rating of 0 out of 5 stars

AREA-XL 017/03 Spare brake pads
Spare part for AREA-XL 017/02 Center differential tower with tuning brake system for Losi Desert XL.Content:4 pieces Montage video:

€29.90*

Average rating of 0 out of 5 stars

AREA-XL 017/06 Spare brake pad adjustment screws with O-ring
Spare part for AREA-XL 017/02 Center differential tower with tuning brake system for Losi Desert XL.Content:2 pieces Montage video:

€9.90*

Customers also viewed

Average rating of 0 out of 5 stars

SB015TSH GPM aluminum split servo horn for 15T shaft
Genuine GPM spare/option part. Extremely sturdy split-style servo horn, fits servos with 8 mm/15T output shaft (e.g. DM4000, large Savöx/Losi/Hitec, Multiplex Rhino etc.). It is therefore also suitable for use in many other applications. Linkage mounting holes tapped for M4 screws.Contents:1 piece

€17.90*

Average rating of 0 out of 5 stars

DYNR0112 Dynamite Alloy Throttle Servo arm 15T for Losi DBXL
Genuine Dynamite spare/option part.New Dynamite large scale servo arms are machined from high quality 7075 T6 aluminum material to withstand the high demand of giant scale RC surface applications.Fits servos with 8 mm / 15T shaft like i.e. Savöx 236, Losi S900S, Losi S 901, Spektrum 9010 and 9020.Features:Perfect fit every time CNC Machined for consistent and accurate tolerancesHigh Strength Made with 7075 T6 AluminumSecure connection Clamping styleGreat looks Red anodized aluminumContent:1 piece

€19.99*

Average rating of 0 out of 5 stars

AT-DBXL016 ATOP aluminum steering rods for Losi DBXL-E 2.0
Genuine ATOP spare/option part. Steering rods for Losi DBXL-E 2.0 with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Dimensions: Hole to hole: 108mm Total length: 128mm Contents:2 pieces

€34.90*

Average rating of 0 out of 5 stars

y1388 Offroad tuning springs Dirt-Spring DBXL/XL-E +MTXL
y1388 Version: y1388/06 - 3,0 x 110 mm Gold, 1 pair
Genuine HT spare/option part. Fits Losi Desert Buggy XL stock shocks.The Desert Buggy XL stock springs use a high preload, which is even bigger than the shocks travel. This means that the stock spring action increases not that much going through the available suspension travel. To handle hard impacts high viscosity oil is used in the shocks; however, this oil is too heavy for these springs for a proper rebound. A sensible suspension tuning becomes much pretty difficult.For this reason, the tuning springs Dirt-Spring Desert Buggy XL are shorter than the stock springs, but also use heavier gauge wire in return. Therefore the change in spring action during the suspension travel is noticeably higher than the preload; the suspension settings can be influenced more effectively.Due to their different characteristics the stock springs are difficult to be sorted among the line of the tuning springs.As a rule of thumb theyre similar to the 2.7 mm version when used with the current 2000 viscosity oil factory fill.Dimensions:Inner diameter: 35 mmFree length: 110 mmNumber of turns: 9Versions:y1388/01 - 2,5 x 110 mm Ochery1388/02 - 2,6 x 110 mm Bluey1388/03 - 2,7 x 110 mm Greeny1388/04 - 2,8 x 110 mm Silvery1388/05 - 2,9 x 110 mm Whitey1388/06 - 3,0 x 110 mm Goldy1388/08 - Complete set, unit prices: 132,93 EUR 

€21.99*
%

Average rating of 0 out of 5 stars

y2005 Tuning aluminum engine mount set for all FG 4WD Sportsline cars
Tuning aluminum engine mount set for all FG 4WD Sportsline cars: Monster-Truck, Off-Road Buggy, Marder, Beetle, Touring Cars.Inhalt:Aluminum large engine / layshaft mountAluminum small engine mountAll necessary screws are included!

€99.90* €124.80* (19.95% saved)

Average rating of 0 out of 5 stars

DM4000/01 Alloy servo arm for K-Power, Losi, Savöx, Spektrum, Rhino, Hitec and many more
Genuine K-Power spare/option part.One-piece aluminum servo arm, 67 mm long and 3 mm thick, with 10 linkage hole tapped for M3 screws.Suitable for all servos with an output shaft with 15 tooth spline shaft, for example:K-Power DM4000Multiplex RhinoHitec 805Savöx SV-0236MGSpektrum S9010 and S9020LOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)and many more!When you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servo arms are indispensable by strong digital servos, as used on large scale models for example, to optimize the servo forces being transferred.Content:1 pieces

€13.95*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Plugin Development