Fits FG Monster and Stadium carsAre you owner of a Monster Truck or Monster Jeep, or perhaps of a Stadium Hummer? You are not really satisfied with the driving performance of your model, or you just want more driving fun? In this case we recommend to install the new 4WD conversion kit made by FG. The conversion kit includes all parts necessary to convert your 2WD Monster model to a 4WD model (complete front diff included). Assembly instructions are included.Fits the following FG cars:- Monster Truck- Monster Hummer- Monster Jeep- Monster Beetle Pro- Stadium Truck-Stadium Hummer- Stadium Jeep- Stadium Beetle ProPlease note: the radio plate is designed to accept a 805-sized servo (case length 65 mm). For installation of a Rhino (case length 58 mm) or a similar sized servo you need to order radioplate y0532 separately.The exploded view shows a partially assemled kit, therefore you can't see every single part included! The video shows the FG Off-Road Buggy 4WD during a test drive for a presentation in the Cars & Details magazine!The entire chassis is 100% identical to the FG cars Marder 4WD; Beetle 4WD and Monster / Stadium 4WDEnjoy the video!
Genuine FG spare/option part. Fits FG 2WD Marder.Offer your Marder a new life - it will be out of all recognition! Aggressive in the curves, dead on the line - just everything which guarantees pure driving fun. The well-tried 4WD by FG is now available as conversion kit for your 2WD Marder. You will not realize from the outside that the model is equipped with a fourwheel drive. But you and your rc-car friends will notice it considerably as soon as you start your model and speed up properly.The conversion kit includes all parts necessary to convert your 2WD Marder to a 4WD Buggy. A mounting instruction is enclosed.Please note: the radio plate is designed to accept a 805-sized servo (case length 65 mm). For installation of a Rhino (case length 58 mm) or a similar sized servo you need to order radioplate 68241 separately.Contents:1 set
Item N° 68503Conversions kit FG Leopard Sportsline 2WD to 4WD, setThis kit enables a conversion of the Leopard 2 into a Leopard 4 model with fourwheel drive. The conversion kit contents all chassis respectively drive components needed for the conversion.
Genuine FG spare/option part. Individual prices of the parts in the tuning set: 847,06 EurosAluminum conversion kit to aluminum front axle and aluminum rear knuckle and wishbone for FG Marder.Contents:1 set
Genuine FG spare/option part.This conversion kit includes all necessary parts to convert a 4WD Off-Road Buggy with a wheelbase of 500mm to a 4WD Off-Road Buggy WB535 with a wheelbase of 535mm. The bodyshell is not included, the existing bodyshell can be adapted.
For converting the Sportsline long touring car into a model with 4WD drive. The conversion kit contains all chassis parts and drive parts that are required for the conversion.
Genuine Top Tuning spare/option part. All aluminum parts are made of 7075 alloy.Front motor mount design to assure ample clearance for the rear brake disc when running mechanical brakes.Accepts two batteries up to 150 mm long und 50 mm wide. The battery tray accepts batteries up to 164 mm long, but the motor pinion limits the max. length of one battery to 155 mm.Rear motor clamps:Diameter 57 mm i.e. for Tenshock or CastleDiameter 57,8 mm i.e. for Leopard 58 lineDiameter 60 mm i.e. for LehnerDiameter 70 mm i.e. for BP70120 ZTW Beast Brushless engine 620 kVPlease note: This set does not include Motor or ESCThis conversion kit is not intended for the 5ive-T 2.0, even though the installation in this vehicle would be feasible with some modifications (drilling and thread tapping required). The version for the 5ive-T 2.0 you can find here: TT1024. Driving batteries with the following maximum dimensions can be installed: Length: 165 mm Width: 51 mm Height: variable The speed controller (ESC) requires EC8 connections or corresponding ! Contents:Motor mount with your choice of rear clamp for 57 / 57.8 / 60 / 70 mm motor diameterBattery carrier plate made of 3 mm epoxy with aluminum brackets for the hook-and-loop tapes4 hook-and-loop tapes to secure the batteriesaluminum mounting pedestals for the battery plate16T pinion with 8 mm bore diameterMounting screws
Genuine Top Tuning spare/option part.This kit includes all required parts for converting a Losi 5ive-T, 5ive-B or Mini into an electric car.Contents:TT1021 Top Tuning Electric conversion kit for Losi 5ive-T/B and Miniand your choice of Motor and ESC: either y1531/01: ZTW Beast Pro 200A ESC and 56112 ZTW Monster Brushless Motor 700 kV or y1549/01: TT Beast Pro 300A 12S ESC with TT70120 620KV Brushless motor TT1021 Top Tuning Electric conversion kit for Losi 5ive-T/B and MiniAll aluminum parts are made of 7075 alloy.Front motor mount design to assure ample clearance for the rear brake disc when running mechanical brakes.Accepts two batteries up to 155 mm long und 50 mm wide. The battery tray accepts batteries up to 164 mm long, but the motor pinion limits the max. length of one battery to 155 mm.Rear motor clamp diameter 57,8 mm i.e. for Leopard 58 lineContents:Motor mount, rear clamp for 57.8 mm motor diameterBattery carrier plate made of 3 mm epoxy with aluminum brackets for the hook-and-loop bands4 hook-and-loop bands to secure the batteriesaluminum mounting pedestals for the battery plate16T pinion with 8 mm bore diameterMounting screwsy1567 ZTW Beast Pro 200A ESC:Specification:Conzinous current: 200ABurst current: 1300ABEC: 6,0 V/7,4 V adjustable / 8 ABattery NIXX / LiPo: 8 - 24NC / 6-8S LiPoWidth: 55 mmLength: 90 mmHeight: 50 mmWeight: 407gProgrammable: JaWaterproof: JaSuitable Car: 1/5 Buggy/TruggySuitable car weight: 13kg y1567 ZTW Beast Pro 200A ESC:Specifications:Max. Amps: 175AMax. Voltage: 42VMax. Power: 7.350WKV (RPM/Volt): 700KVMounting hole depth: 8 mmBolt pattern: 4 x M4 on each 30 mmCase diameter: 57,8 mmCase length: 112 mmFree shaft length: 30 mmShaft diameter: 8 mmGewicht: 1260gAlternative:y1549/01 TT Beast Pro 300A 12S ESC with TT70120 620KV Brushless Motor: y1549 ZTW Beast Pro 300A 12S ESC Specification:Continuous Current: 300ABurst Current: 1800ABEC: 6,0 V/7,4 V einstellbar / 8 ABattery NIXX / LiPo: 18 - 36NC / 6-12S LiPoWidth: 74 mmLength: 115 mmHeight: 78 mmWeight: 500gProgrammable: JaWaterproof: splash proofTT70120 Top Tuning Beast Brushless Motor 620 kVSpecifications:Max. Amps: 200AMax. Voltage: 8-14SMax. Power: 10.000WKV (RPM/Volt): 620KVResistance: 0,0095Mounting hole depth: 8 mmCase diameter: 70 mmCase length: 120 mmFree shaft length: 30 mmShaft diameter: 8 mmGewicht: 1730g
Genuine Top Tuning spare/option part.This kit includes all required parts for converting a Losi 5ive-T 2.0 into an electric car.Contents:TT1024 Top Tuning Electric conversion kit for Losi 5ive-T 2.0y1531/01 ZTW Beast Pro 200A ESC and 56112 ZTW Monster Brushless Motor 700 kVTT1024 Top Tuning Electric conversion kit for Losi 5ive-T 2.0 Genuine Top Tuning spare/option part. All aluminum parts are made of 7075 alloy.Front motor mount design to assure ample clearance for the rear brake disc when running mechanical brakes.Accepts two batteries up to 164 mm long und 50 mm wide. Rear motor clamps:Diameter 57 mm i.e. for Tenshock or CastleDiameter 57,8 mm i.e. for Leopard 58 lineDiameter 60 mm i.e. for LehnerDiameter 70 mm i.e. for BP70120 ZTW Beast Brushless engine 620 kVThis conversion kit is for the 5ive-T 2.0 only. It even allows for running the big BP70120 ZTW Beast Brushless motor in combination with mechanical brakes! The center diff will be turned around between its mounting pillars for installation.Contents:Motor mount with your choice of rear clamp for 57 / 57.8 / 60 / 70 mm motor diameterBattery carrier plate made of 3 mm epoxy with aluminum brackets for the hook-and-loop bands4 hook-and-loop bands to secure the batteriesaluminum mounting pedestals for the battery plate17T pinion with 8 mm bore diameterMounting screws y1567 ZTW Beast Pro 200A ESC:Specifications:Max. Amps: 175AMax. Voltage: 42VMax. Power: 7.350WKV (RPM/Volt): 700KVMounting hole depth: 8 mmBolt pattern: 4 x M4 on each 30 mmCase diameter: 57,8 mmCase length: 112 mmFree shaft length: 30 mmShaft diameter: 8 mmGewicht: 1260g y1549/01 ZTW Beast Pro 300A 12S ESC with BP70120 620KV Brushless motor: Genuine ZTW spare/option part. In our shop selection, the set is also available with the 300A ZTW BEAST 12S controller and 620kV motor at an additional cost. y1549 ZTW Beast Pro 300A 12S ESC Features:Enchanced throttle response, excellent acceleration, linearity and driveabilityUsind the advanced PC interface allows you to set up, program or update the firmwareFully Programmable via LCD program card, PC interfaceAdjustable BEC output 6.0/7.4V, up to 8A current outputMultible protection features: Low voltage cut-off protection, over-heat protection and throttle signal loss protectionSpecification:Continuous Current: 300ABurst Current: 1800ABEC: 6,0 V/7,4 V einstellbar / 8 ABattery NIXX / LiPo: 18 - 36NC / 6-12S LiPoWidth: 74 mmLength: 115 mmHeight: 78 mmWeight: 500gProgrammable: JaWaterproof: splash-proof BP70120 ZTW Beast Brushless motor 620 kV Specifications:Max. Amps: 200AMax. Voltage: 8-14SMax. Power: 10.000WKV (RPM/Volt): 620KVResistance: 0,0095Mounting hole depth: 8 mmCase diameter: 70 mmCase length: 120 mmFree shaft length: 30 mmShaft diameter: 8 mmGewicht: 1730g Driving batteries with the following maximum dimensions can be installed: Length: 165 mm Width: 51 mm Height: variable The speed controller (ESC) requires EC8 connections or corresponding adapter cables! Features:High Quality BearingsRotor-4Pole High Quality MagnetsStator-Super Thin Silicon Steels Super Strength 8mm ShaftCNC Aluminium Heatsink ShellCopper Wires Of High Temperature EnduranceContents:1 set
Genuine Top Tuning spare/option part. All aluminum parts are made of 7075 alloy.Front motor mount design to assure ample clearance for the rear brake disc when running mechanical brakes.Accepts two batteries up to 164 mm long und 50 mm wide. Rear motor clamps:Diameter 55,75 mm i.e. for Losi Spektrum 780 kV Diameter 57 mm i.e. for Tenshock or CastleDiameter 57,8 mm i.e. for Leopard 58 lineDiameter 60 mm i.e. for LehnerDiameter 70 mm i.e. for BP70120 ZTW Beast Brushless engine 620 kVPlease note: This set does not include Motor or ESCThis conversion kit is for the 5ive-T 2.0 only. It even allows for running the big BP70120 ZTW Beast Brushless motor in combination with mechanical brakes! The center diff will be turned around between its mounting pillars for installation. Driving batteries with the following maximum dimensions can be installed: Length: 165 mm Width: 51 mm Height: variable The speed controller (ESC) requires EC8 connections or corresponding ! Contents:Motor mount with your choice of rear clamp for 57 / 57.8 / 60 / 70 mm motor diameterBattery carrier plate made of 3 mm epoxy with aluminum brackets for the hook-and-loop bands4 hook-and-loop bands to secure the batteriesaluminum mounting pedestals for the battery plate17T pinion with 8 mm bore diameterMounting screws
Genuine Top Tuning spare/option part. Beast Edition: Losi XL-E Standard equipment: Beast Edition: Motor: 780kV 520kV Regler: 160 Ampere 300 Ampere S-Leistung: 8S 12S 8S is not enough? You want to go to the limit? Then we have the right thing for you! With the Top Tuning conversion kit it is now possible to mount the ZTW Beast Pro Combo. With the torquey 620KV motor and the 12S 300A esc even the roughest off-road tracks are no problem anymore. The esc is fully programmable using the separately available programming card and can therefore be adapted to all track conditions. In addition, the supplied 15T pinion provides higher gearing and when driving with 12S, top speed is increased by approx. 20%.TT56112/520Top Tuning Monster Brushless Motor 520kV Max. amps: 129 A Max. voltage: 57 V Max. power: 7,350 W KV (RPM/Volt): 520 KV Mounting hole depth: 8 mm Bolt pattern: 4 x M4 at 30 mm pitch circle diameter Case diameter: 57.8 mm Case length: 112 mm Free shaft length: 30 mm Shaft diameter: 8 mm Weight: 1260 g Connector: 6.5 mm diameter Cable size: 8AWG y1549 ZTW Beast Pro 300A 12S ESCSpecification:Continuous Current: 300ABurst Current: 1800ABEC: 6,0 V/7,4 V einstellbar / 8 ABattery NIXX / LiPo: 18 - 36NC / 6-12S LiPoWidth: 74 mmLength: 115 mmHeight: 78 mmWeight: 500gProgrammable: JaWaterproof: splash-proofContents:1 piece
Complete set with all required installation parts!50% more power than aZenoah G320 engine! Spektrum Firma® 160 Amp Brushless SMART ESC The ESC is waterproof, completely programmable, and comes pre-wired with a high-current IC5 connector. The ESC will work with most sensorless brushless motors and is Li-Po and Ni-MH compatible. The SMART technology provides information like battery voltage, RPM, RX pack Voltage, and Speed directly from the ESC when used with the Spektrum Dashboard app. 50+ MPH Spektrum Firma 4-Pole 780Kv Brushless Motor The brushless ESC and motor provide wicked power with an 8s LiPo battery (not included) that will blaze speeds of 50+ MPH. Perfect option for 1/5th scale models looking to run a 8S Lipo powered setup. Featuring a low cog 4-pole 8-magnet rotor design, CNC machined aluminum housing with heat sinking fins, insulated high purity copper windings, high-quality alloy steel 8mm output shaft, and high-precision bearings for high durability and smooth rotation. Preinstalled with 6.5mm gold plated bullet connectors. Perfectly matched to the Firma 160 Smart ESC. FAST, POWERFUL M4 PROCESSOR The Firma ESCs' 32-bit M4 processor produces higher resolution signal input and more accurate motor output. TT1021 Top Tuning Electric conversion kit for Losi 5ive-T/B and MiniAll aluminum parts are made of 7075 alloy.Front motor mount design to assure ample clearance for the rear brake disc when running mechanical brakes.Accepts two batteries up to 150 mm long und 50 mm wide. The battery tray accepts batteries up to 164 mm long, but the motor pinion limits the max. length of one battery to 155 mm.This conversion kit is for the Losi 5iveT/B and Mini. The conversion kit for the Losi 5ive-T 2.0 has the order number TT5014 Driving batteries with the following maximum dimensions can be installed: Length: 165 mm Width: 51 mm Height: variable The speed controller (ESC) requires EC8 connections or corresponding adapter cables! Contents: SPMXSM1100 Spektrum Firma 780Kv Brushless Motor SPMXSE1160 Spektrum Firma 160 Amp Brushless Smart ESC 3S-8S Motor mount with your choice of rear clamp Battery carrier plate made of 3 mm epoxy with aluminum brackets for the hook-and-loop bands 4 hook-and-loop bands to secure the batteries aluminum mounting pedestals for the battery plate 17T pinion with 8 mm bore diameter Mounting screws
Complete set with all required installation parts!50% more power than aZenoah G320 engine! Spektrum Firma® 160 Amp Brushless SMART ESC The ESC is waterproof, completely programmable, and comes pre-wired with a high-current IC5 connector. The ESC will work with most sensorless brushless motors and is Li-Po and Ni-MH compatible. The SMART technology provides information like battery voltage, RPM, RX pack Voltage, and Speed directly from the ESC when used with the Spektrum Dashboard app. 50+ MPH Spektrum Firma 4-Pole 780Kv Brushless Motor The brushless ESC and motor provide wicked power with an 8s LiPo battery (not included) that will blaze speeds of 50+ MPH. Perfect option for 1/5th scale models looking to run a 8S Lipo powered setup. Featuring a low cog 4-pole 8-magnet rotor design, CNC machined aluminum housing with heat sinking fins, insulated high purity copper windings, high-quality alloy steel 8mm output shaft, and high-precision bearings for high durability and smooth rotation. Preinstalled with 6.5mm gold plated bullet connectors. Perfectly matched to the Firma 160 Smart ESC. FAST, POWERFUL M4 PROCESSOR The Firma ESCs' 32-bit M4 processor produces higher resolution signal input and more accurate motor output. TT1024 Top Tuning Electric conversion kit for Losi 5ive-T 2.0All aluminum parts are made of 7075 alloy.Front motor mount design to assure ample clearance for the rear brake disc when running mechanical brakes.Accepts two batteries up to 164 mm long und 50 mm wide. This conversion kit is for the 5ive-T 2.0 only. The conversion kit for the Losi 5iveT/B and Mini has the order number TT5013 Driving batteries with the following maximum dimensions can be installed: Length: 165 mm Width: 51 mm Height: variable The speed controller (ESC) requires EC8 connections or corresponding adapter cables! Contents: SPMXSM1100 Spektrum Firma 780Kv Brushless Motor SPMXSE1160 Spektrum Firma 160 Amp Brushless Smart ESC 3S-8S Motor mount with your choice of rear clamp Battery carrier plate made of 3 mm epoxy with aluminum brackets for the hook-and-loop bands 4 hook-and-loop bands to secure the batteries aluminum mounting pedestals for the battery plate 17T pinion with 8 mm bore diameter Mounting screws
y1308 Version:
y1308/03 Set with mount A and Mount B+ 27.9EUR
Genuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 set
Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
Fits 5ive-T 2.0 as well!Set includes:y1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 All steel linkage steering servo/servo saver applicationy1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1308/01 + y1308/02 Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 sety1309 All steel linkage for Losi 5ive-T and Mini steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
Fits 5ive-T 2.0 as well!Set includes:y1378 Dymond LiPo special high current receiver battery 14.8V/2200mAhy1306 - Servo voltage regulatory1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 - Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 - Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 - All steel linkage steering servo/servo saver applicationy1378 - LiPo special high current receiver battery 14.8V/2200mAhGenuine FG spare/option part. This battery is especially for use in vehicles which are equipped with the Hitec Servo HS-900SGS/HS-1000SGT/1005SGT/HS-1100WP for external high-voltage power supply. This battery comes with a Y-adaptor harness for two connectors, one each JST and Futaba/Universal connector. The JST connector is used for hooking up to the steering servo; the universal connector is used for the voltage regulator. The battery fits into the standard battery box of the Losi 5ive-T. Dimensions:Length: 110 mmWidth: 32 mmHeight: 33 mmWeight: 247 grConfiguration: 4S1pCurrent rating: 40C (66 A)Recommended charging current: up to 3C (2.2 A)XHP(XH) -balancer connector To increase the battery's life span it is recommended to use a charging current of approx. 0.8 A for the first three cycles.Contents:1 piecey1306 - Servo voltage regulatorThe switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piecey1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1308/01 + y1308/02 - Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 sety1309 - All steel linkage for Losi 5ive-T and Mini steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
Fits 5ive-T 2.0 as well!Set includes:Hitec Servo HS-1100WPy1378 Dymond LiPo special high current receiver battery 14.8V/2400mAhy1306 - JETI-SBEC 6-42V voltage regulatory1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 - Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 - Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 - All steel linkage steering servo/servo saver applicationy1378 - LiPo special high current receiver battery 14.8V/2200mAhGenuine FG spare/option part. This battery is especially for use in vehicles which are equipped with the Hitec Servo HS-900SGS/HS-1000SGT/1005SGT/HS-1100WP for external high-voltage power supply. This battery comes with a Y-adaptor harness for two connectors, one each JST and Futaba/Universal connector. The JST connector is used for hooking up to the steering servo; the universal connector is used for the voltage regulator. The battery fits into the standard battery box of the Losi 5ive-T. Dimensions:Length: 110 mmWidth: 32 mmHeight: 33 mmWeight: 247 grConfiguration: 4S1pCurrent rating: 40C (66 A)Recommended charging current: up to 3C (2.2 A)XHP(XH) -balancer connector To increase the battery's life span it is recommended to use a charging current of approx. 0.8 A for the first three cycles.Contents:1 piecey1306 - Servo voltage regulatorThe switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piecey1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT Losi 5ive-TGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1309 - All steel linkage for Losi 5ive-T steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 pieceHitec Servo HS-1100WPGenuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece
Genuine rc-car-online spare/option part. This kit makes it possible to equip the Carson Dirt Attack XXL and Dirt Attack GP 2.0 with a Hummer body shell. The kit contains all necessary parts such as body shell, body mounts and decals.This conversion kit fits the electric and gas version of the Carson Dirt Attack only!Contents: 1x 30130 Hummer body shell, black1x 36155 car-specific decals2x 7154 body mount2x 7155 adjustable body mount1x 60237/01 FG plastic strut1x 6815/03 FG Alloy spacer bolts with M4 female thread2x screws M4x22 mm2x nut M4>4x washer 4 mmContents:1 piece
Genuine rc-car-online spare/option part. This kit makes it possible to equip the Carson Dirt Attack XXL with a Hummer body shell. The kit contains all necessary parts such as body shell, body mounts and decals.This conversion kit fits the electric version of the Carson Dirt Attack only!Contents:1x Monster Truck body white or yellow1x 20155 FG Vehicle decals Monster1x 7154 Body mount2x 7155 Body mount adjustable1x 60237/01 FG Plastic brace1x 6815/03 FG Alloy mounting bolts bilateral with 4mm screw thread8x Screws M4x16
The conversion kit contains all mechanical parts (no electric motor, esc and batteries) you need to convert a Carson Wild Attack or HPI Baja 5B to electric drive.Brushless motors from all common manufacturers with 56 - 58 mm diameter, about 100 - 115 mm motor can length, 700 - 850 KV and 8 mm output shaft will fit. We recommend the TT56112/700 Top Tuning Monster Brushless Motor 700 kV.For the esc,ZTW Beast 200A or other ESCs with similar dimensions and performance data are suitable.The battery box provides a total space of 180 x 84 x 50 mm for the batteries. Operation with 6S - 8S is recommended.The set contains: Battery and receiver box Complete aluminum motor mount Ball bearing for intermediate shaft Motor pinion Chassis struts and mounting plate for esc made of aluminum Extension cable for speed controller installation hardware Exploded view and assembly instructions
€269.90*
This website uses cookies to ensure the best experience possible. More information...