y0057 Ball & socket tool for Losi and HPI
€22.90
Available
Product information "y0057 Ball & socket tool for Losi and HPI"
Ball & socket tool with t-handle, special version for the ball joints.
Fits Losi 5ive-T. 5ive-B, Desert Buggy XL, Desert Buggy XL-E, Monster Truck XL and the HPI Baja 5B and Baja 5R Ford Mustang.
Contents:
- 1 piece
Login
Customers also bought
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum chassis braces, for Losi DBXL 2.0.Compared to the stock plastic parts (from sets # LOS251115 and LOS251116) the higher strength of the aluminum parts noticeably increases the chassis rigidity.Contents:1 piece
Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece
Genuine HT spare/option part. Helpful tool for removal of clutch shoes, flywheels and many more.FitsZenoah G230/G240/G260/G270/G290/G320Chung-Yang enginesPT enginesLosi enginesHPI enginesThreadsize:M10 x 1Contents:1 piece
Genuine HT spare/option part. With non-slip surface perfect for delicate work, actually improving dexterity and grip.Available sizes: 8, 9 and 10.Glove size?Size 8 = 21 cm (S - L) circumferenceSize 9 = 24 cm (L - XL) circumferenceSize 10 = 27 cm (XL - XXL) circumferenceMeasure the circumference of your hand without the thumb and at the widest point (above the ankle). The tape measure should embrace the hand loosely.Norm EN388, Lining 100% polyamide.Partially coated with hightech nitrile Fits like a second skinGrips even when wetGood touch sensitivityLiquid-repellentGood resistance against oil and greaseContents:1 pair / 2 pieces3 pairs / 6 pieces
Genuine ATOP spare/option part.Light weight design (108 grams each), CNC-machined from 6061-T6 aluminum by ATOP a-arms fits Losi 5ive-T front.The chassis-side is wider than stock arms to bring the large longitudinal play at this point down to a reasonable level.Bushings for the hinge pins guarantee low wear. On the wheel side floating stainless steel bushings allow for normal tightening of the c-hub screws.Contents:1 set
Customers also viewed
For ball bearings (diameter 8 x 22 mm) in steering blocks and uprights.Instructions:Remove the M5 bolt until the gap between the bolt's head and the top of the spindle is slightly more than the the width of the bearingInsert the spindle with the bolt into the bearing and srew the bolt in with an allen key from the opposite (do not tighten the bolt!)Now remove the bearing by just turning the spindle ccw
Tool and screw tray with quick-mount clamp, fits tubes with a diameter from 32 to 35 mm. Thus perfectly suitable for the TopTuning Car Stand TT1030 and for many other holders.Due to a strong design with high quality materials, a very high load capacity is achieved. Many possibilities to store tools and small parts to have them handy at any time when working with the Car Stand. The adjustable clamp allows the mounting of more than one Tool Tray. Contents: with foldable Tool Tray with milled adapter block with mounting clamp
Servo direct power supply cable with electronic switch, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.The integrated electronic receiver switch is rated 5 A continuous / 15 A peak. This switch does not use mechanical contacts for the load; therefore it is less prone to failure caused by vibrations or dirt. With separate charging connector.With drilling template and mounting material included.
Genuine Losi spare/option part. Contents:1 pair / 2 pieces
Genuine Area spare/option part. Fits AREA-XL 021 Aluminum rear uprights for Losi DBXL.Contents:4 pieces
Genuine HT spare/option part. Ball & socket tool with t-handle, especially for installation and removal of balls in FG or Smartech/Carson cars' plastic a-arms and steering rod ball joints.Contents:1 piece
Genuine Losi spare/option part.The set is for two tires (one pair).Content:1 set