Genuine Smartech/Carson spare/option part. Tire diameter 170 mm, tire width 80 mm, 18 mm wheel square. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Contents:1 pieceAlso suitable for:With the following wheel adapter: y1183 Rim adapter
Item N° 06407/05 Mini pin M / OR tires, glued, white, 2 pcs.Spare part for the Leopard 2010 2WD/4WD versionThe new FG Mini Pin tires are designed for harder grounds. They grant the model a lot of stability and tremendous grip in curves. 153 mm diameter64 mm wideThe version M is suitable for cooler temperatures lower than 20°, die version H is for temperatures over 20°. The tires are glued ready to run on the widened 1:6 wheels.These wheels are suitable for the FG Marder, Beetle, Off-Road Buggy and the monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Genuine FG spare/option part.With a diameter of 185mm extremely large and 85mm wide OR Truggy tire. Glued on new Truggy rim. A lot of grip, therefore high curve speeds on almost every surfaces possible. Available in different hardnesses. Suitable for all FG Buggy and Monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Genuine FG spare/option part.With a Ø of 185mm extremely large and 85mm wide OR Truggy tire. Glued on new Truggy rim. A lot of grip, therefore high curve speeds on almost every surfaces possible. Available in different hardnesses. Suitable for all FG Buggy and Monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Genuine FG spare/option part.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Contents:1 pair
Genuine FG spare/option part. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Dimensions:Diameter: 170 mmWidth: 65 mmWeight: 367 gramContent:2 pieces / 1 pair
Genuine FG spare/option part.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Dimensions:Diameter: 170 mmWidth: 65 mmWeight: 367 gramContent:2 pieces / 1 pair
Item N° 67210/04 Mini Pin S / OR tires, Leo wheel white, glued, 2pcs.Completely new revised and in important details improved Mini Pin Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant.The FG Mini Pin tires are especially well-suited for hard and rough ground. They give the model a lot of traction, driving stability and grip in curves. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. The tires are ready glued on the new Leo wheels. For the assembly you need the 12mm square wheel drivers (ItemN°. 06107/07).The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models.
Item N° 67210/05 Mini Pin M / OR tires, Leo wheel white, glued, 2pcs. Completely new revised and in important details improved Mini Pin Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Pin tires are especially well-suited for hard and rough ground. They give the model a lot of traction, driving stability and grip in curves. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle.The tires are ready glued on the new Leo wheels. For the assembly you need the 12mm square wheel drivers (Item-no.: FG 6107/07). The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Item N° 67210/06 Mini Pin H / OR tires, Leo wheel white, glued, 2pcs. Completely new revised and in important details improved Mini Pin Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Pin tires are especially well-suited for hard and rough ground. They give the model a lot of traction, driving stability and grip in curves. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle.The tires are ready glued on the new Leo wheels. For the assembly you need the 12mm square wheel drivers (Item-no.: FG 6107/07). The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Item N° 67213/06 Mini block H / OR tires, Leo wheel white, glued, 2pcs. Spare part for the Leopard 2010 2WD/4WD versionThe Mini Block tires are develepod for slightly loose underground. They are excellent as front tire for the 2WD models in connection with the Mini Pin tires on the rear axle. These tires are glued ready to run on the new Leo 1:6 wheels. The Leo wheels are not suitable for the FG Marder, Beetle, Off-Road Buggy and the monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Item N° 67214/04 Mini block S / OR tires, glued, white, 2pcs.Completely new revised and in important details improved Mini Block Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant.The FG Mini Block tires are especially well-suited for slightly loose and humid ground. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. The Mini Block tires are also well-suited as front tires for 2WD models in combination with the Mini Pin tires on the rear axle. The tires are ready glued on the new Leo 1:6 wheels. For the assembly you need the 12mm square wheel drivers (ItemN°. 06107/07).The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models.
Item N° 67214/05 Mini block M / OR tires, glued, white, 2pcs.Completely new revised and in important details improved Mini Block Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant.The FG Mini Block tires are especially well-suited for slightly loose and humid ground. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. The Mini Block tires are also well-suited as front tires for 2WD models in combination with the Mini Pin tires on the rear axle. The tires are ready glued on the new Leo 1:6 wheels. For the assembly you need the 12mm square wheel drivers (ItemN°. 06107/07).The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models.
Item N° 67214/06 Mini block H / OR tires, glued, white, 2pcs.Completely new revised and in important details improved Mini Block Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Block tires are especially well-suited for slightly loose and humid ground. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. The Mini Block tires are also well-suited as front tires for 2WD models in combination with the Mini Pin tires on the rear axle. The tires are ready glued on the new Leo 1:6 wheels. For the assembly you need the 12mm square wheel drivers (ItemN°. 06107/07).Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models.
The MCD Astro-Grip is one of the most widely used tires in large scale off-road racing. Especially on astro turf and firm clay it provides optimal grip and is resistant to wear. The reinforced shoulder largely protects the tire from damage. Therefore the radial ribbing should normally be mounted on the outside of the. Due to the increased stiffness and some sort of added tread, the ribs also improve the tires traction during cornering.If this effect is not desired (i.e to reduce steering on the front axle), you can also mount the tires with the ribs to the inside, of course. It just has be considered when you glue the tires. Another way to reduce the tires grip at the outer edge is cutting some of the outer pins. This makes a tire less aggressive during cornering; another possibility to match the cars behavior to the track and make it more drivable. A pleasant vehicle setup can often be achieved by running used MCD Astro-Grip tires on the front axle and new ones on the rear.Dimensions:Outside diameter: approx. 180 mmInside diameter: approx. 130 mmWidth: approx. 65 mmWeight: one glued tire on Hurrax rim: 370 grams Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms
Genuine GRP spare/option part.Glued on GRP off-road disc rim with 18 mm square (für FG, Smartech & other) or 24 mm hex (for Losi, HPI + Co.). GRP is one of the leading manufacturers of 1/5 and 1/6er street; and with its current off-road tires MICRO and CROSS he has the optimal solution for all track conditions and surfaces. As a recommendation: The dirtier the track or the colder the weather, the more grippy (softer) the rear tire should be.Note regarding the front tires: For 2WD cars it should be one to two steps harder than the rear tire. On 4WD models, a tire combination with the same shore hardness front and rear is usually a good choice.Of course, as with all tires, it also applies to the GRP tires MICRO and CROSS: the softer the tire, the higher the wear.The MICRO tire is perfect for astro turf as well as carpet flooring; the CROSS version gives your off-road car the necessary grip on loose as well and firmer soil alike.The following classification should help you with the tire selection, even though it is certainly recommended to find the best possible tire for your individual setup by your own test drives on the track.GRP-MICRO GW90-P1 soft for astro turf/carpet tracks, in colder weather and low grip conditionsGRP-MICRO GW90-P3 medium for astro turf/carpet tracks, but at higher temperatures and good gripGRP-MICRO GW90-S1 soft for clay soil, on colder days and less grip on the trackGRP-MICRO GW90-S3 medium also suitable for natural terrain, at normal temperatures and good grip.GRP-MICRO GW90-S5 hard, for good to very good grip conditions and/or good weatherBut as already said: "The proof is in the pudding", which means that a GRP-MICRO-S tire can also prove to be the best on a specific astro turf track, depending on the tracks condition and weather! And, of course, vice versus with a GRP-MICRO P tire. This applies especially to race tracks with a mix of carpet/astro turf and sorts of natural soil surface sections.As with full scale racing, in RC-car races, the right selection of tires often decides on victory or defeat.Technical note: The outside shoulder of the tires is reinforced and is labeled "OUT" by GRP!Contents:2 pieces
Item N° GWH70 GRP 1:6 Buggy "CUBIC" tire glued, 2 pcs.fine lug treadvery good directional stabilitylow lateral tractionmoderate propulsionfor hard packed surfaceTire diameter: 164 mm Tire width: 61 mmDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Attention:On all 2WD cars (except Leopard 2WD) the front suspension must be equipped with the combination of uprights y0932 and steering rods FG #7028/01. Wheel squares FG #6107/02 must be used in front and rear. 4WD cars must only use the wheel squares FG #6107/02 in front and rear.
Item N° GWK70 GRP 1:6 Buggy "CUBIC" tire glued on yellow rims, 2 pcs.fine lug treadvery good directional stabilitylow lateral tractionmoderate propulsionfor hard packed surfaceTire diameter: 164 mm Tire width: 61 mmDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Attention:On all 2WD cars (except Leopard 2WD) the front suspension must be equipped with the combination of uprights y0932 and steering rods FG #7028/01. Wheel squares FG #6107/02 must be used in front and rear. 4WD cars must only use the wheel squares FG #6107/02 in front and rear.
HURRAX extreme Race tire and insert 175x70 mm HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing HURRAX extreme Race tire and insert 175x70 mm HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms
Genuine HT spare/option part. The Maxi-Pin competition tire is particularly suitable for tracks with a hard packed surface, as well as for tracks with a higher percentage of carpeting. The tread is not extended into the tire?s sidewall to reduce the side bite of the Maxi-Pin tire; the car remains controllable on such challenging tracks, which makes this tire a must-have for your "tire box"! Since the Maxi-Pin tire has many fine pins for a high number of biting edges and a low tread depth for reduced flex work, depending on the track?s surfaceincreased tire wear may be expected. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.For wet conditions the soft compound is recommended, under normal condition the medium compound is usually your best choice.Content:Diameter: 155 mmWidth: 67 mmPrices of the components:Maxi-Pin tires: 39,90 EUR / pairMaxi-Pin tire inserts: 9,90 EUR / pairRims FG 6105/01: 14,90 EUR / pairGlue set y0067: 13,30 EURTotal EUR 78.80Ready mounted and glued 69,90 EUR / pair. Rim with 18 mm square drive.Contents:2 pieces / 1 pairAlso suitable for:With the following wheel adapter: y1183 Rim adapter
Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available with either 18 mm square drive to fit FG & co. or with 24mm hex for Losi, HPI Baja 5 series cars and they allready glued!To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the square or hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims for FG, Smartech and Co.:y1400/01 - Tarmac Bustery1401/01 - Big Digger y1402/01 - Cross Bond y1403/01 - Over Lander y1404/01 - Giant Grip y1416/01 - Ultra Gripor for Losi and HPI models: y1406/01 - Big Digger y1407/01 - Cross Bond y1408/01- Over Lander y1409/01 - Giant Grip y1417/01 - Ultra Grip18 mm square for FG & co24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (18 mm square for FG & co24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.24 mm hex for Losi, HPI Baja 5 cars.Contents:2 pieces / 1 pair
Regular price for one pair: 39,90 EURSet with 2 pairs/4 pieces: 79,80 EURGlued on robust 6-spoke star wheels, with 6 ribbed reinforcement bars.With 18 mm wheel square, suitable for most 1:5 / 1:6 RC cars, FG, Carson, etc.Lane widening with 23 mm countersunk nut and 14 mm deep square drive for most models.450 block sections 3.5 mm thick, provide a good grip, even on hard or slippery surfaces.Due to the high-strength 14 mm tire shoulder, the cornering power of the Rallye-Cross 450 is high, despite the high profile of 3.5 mm, but without provoking a disproportionate overdrive of the model.The large inner diameter of 114 mm the rim, as well as the position of the wheel allows on nearly all models to eventually mount a disc brake at the front, as well as rear wheels. The dimension of the inside edge of the rim to the wheel is 20 mm. The 18 mm, 6-braced wheel square of the Rallye-Cross 450 rim is 8 mm deep.Measures of the Rallye-Cross 450 wheel/rim:Outside diameter: 162 mmProfile width: 62 mmRim inside: 114 mmTire shoulder: 14 mmBlock profile: 3,5 mmAlso suitable for:With the following wheel adapter: y1183 Rim adapterWith the following wheel adapter: y0786 Rim adapter
Mounted and glued on reinforced disc rims (with inserts).Diameter 170 mm x width 80 mm, similar to FG Off-Road Buggy rear tires. Multipin tread for excellent grip.18 mm wheel square (with reinforcement ring) fits all FG and Carson / Smartech largescale cars. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
€39.90*
This website uses cookies to ensure the best experience possible. More information...