GPM Air filter cover, no. BJAFCO, 1 pce.
GPM air filter cover which fits easily over your existing air filter. A rubber band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments. Fits all common filters, foam or fabric (K&N) style.
GPM Starter cover, no. BJPSCO
Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.
y1419 Sintered steel clutch for Zenoah and many other engines from 23 cm³ to 32 cm³, incl. clutch spring
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³. incl. clutch spring!Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!
y86479 HighElastic driveshaft boots 47 mm, choice of colors, 4 pcs.
Highly flexible driveshaft boots, equivalent to HPI part # H86479.Available in the following colors:y86479/01 - blacky86479/02 - redy86479/03 - orangeContents:4 pieces
Pink-Racing Reinforced clutch spring y0134, 1 pce.
Reinforced spring for Zenoah OEM clutch with 2.7 mm wire diameter and five coils. Engagement speed is around 7500 rpm, which allows the engine to build up more power and torque for accelleration.Fits Zenoah, CY and most other engines in the 23 - 30 cc range with stock clutch.
y1430 Spark plug tester for 1/5 & 1/6 cars
The spark plug tester wiil be put in line between the spark plug in the engine and the spark plug cap. When the spark plug is in good working order, pulling the recoil starter will produce a spark easily visible in the clear section of the tester (see video!).
y0743 Clutch-Safe 10 g, adhesive especially for clutch pads
Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube
Content: 10 Gramm (€495.00 / 1000 Gramm)
AT-AT001 ATOP Colored high flow fuel line with connections and accessories for Losi 5ive-T/2.0/B, Mini and HPI models
Genuine Atop spare/option part. Colored fuel hose with clams and suction tubesArea Rc High flow fuel line kit.This high flow fuel line kit fits the HPI Baja series and the Losi 5ive-T/B and Mini. It may fit other large scale cars as well.The kit comes with 6 pieces of fuel line clips and 2 assembled plastic fittings. Those fittings cannot be compressed by the tanks fuel line grommet, so the inner diameter remains constant which improves fuel delivery to the carb.Fuel line dimensions:Length: 1mInside diameter: 3 mmOuter diameter: 6 mmAvailable colors: AT001/01 - YellowAT001/02 - RedAT001/03 - BlueAT001/05 - GreenIncludes:2 x Assembled plastic fittings6 x Fuel line clipsTygon fuel line
y0753 Servo mount adapter
Genuine HT spare/option part. This machined aluminum servo adapter allows easy installation of servos with a 69 x 18 mm mounting bolt pattern (for example Orange-Power, S8203) in vehicles / radio plates which provide a 75 x 18 mm mounting bolt pattern (for example Losi 5ive-T, Mini WRC, HPI Baja 5 series cars, many FG cars).The use of this adapter servo will neither tilt the servo, nor does it change installation height. Scope of delivery:1 x Servo mount adapter2 x Socket head cap screws 3 x 20 mm2 x Socket head cap screws 3 x 12 mm2 x Shim ring 3,2 mmContents:1 piece
y0729 Gas-nitrited tuning clutch bell for HPI Baja, Carson Wild GP Attack models, 1 pce.
Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM clutches Big Scale Extreme and Cross.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.
y1011 Zenoah G270RC with Walbro carburetor WT 990
26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:Quantity of cylinder mounting bolts increased from 2 to 4Improved strength of crankcaseAdded additional bearing on the PTO (clutch) side of crankshaftRedesigned shape of cylinder finsDimension of air intake port is 5% widerNew carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.
y1345 Drive pins, choice of sizes, e.g. for Losi, Mini and HPI cars
Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces
y1419/02 Sintered steel clutch complete set for Losi 5ive-T/2.0, Mini and Desert Buggy
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.Content:5315 Clutch block carrier5315/01 Screw for carrier7318 Dowel screw for clutch blocksy1419 Sinter clutchy1419/01 Clutch springs for Sinter clutch
y1524 Complete screws/nuts/washers set for HPI Baja / Carson 1:5 Wild GP Attack
Complete set of screws, nuts and washers for HPI Baja 1/5 vehicles.The set includes a total of 434 screws, nuts and washers in different quantities which are all used on HPI Baja 1/5 vehicles and Carson 1:5 Wild GP Attack.11 sizes of cap head screws9 sizes of CSH screws10 sizes of button head screws4 sizes of set screws2 sizes of washers3 sizes of lock washers3 sizes of self-locking nuts2 sizes of nuts with serrated flange2 sizes of flanged self tapping screwsComes in a high quality 190x170x40 mm assortment box.Contents:Cap head screws in 12.9:20 piecesM3x126 piecesM3x4510 piecesM4x612 piecesM4x1212 piecesM4x2510 piecesM4x306 piecesM4x507 piecesM5x206 piecesM5x306 piecesM5x356 piecesM6x25CSH screws in 10.9:10 piecesM3x2010 piecesM4x1019 piecesM5x1616 piecesM5x206 piecesM5x302 piecesM5x407 piecesM6x14Button head screws in 10.94 piecesM3x1610 piecesM3x303 piecesM4x166 piecesM5x123 piecesM5x302 piecesM5x356 piecesM5x406 piecesM5x452 piecesM6x306 piecesM6x30Grub screws:6 piecesM3x39 piecesM4x46 piecesM4x124 piecesM6x45Washers in Din125:10 pieces3,2x6,8x0,512 pieces4,3x8,7x0,8Safety washers:20 piecesM420 piecesM520 piecesM6Self-locking nuts:10 piecesM310 piecesM415 piecesM5Flanged nuts with serrated base:21 piecesM410 piecesM5CSH screws Torx:10 piecesM4x15 (4,2x16)10 piecesM4x18 (4,2x19)Schneidschrauben Torx mit flanged:10 piecesM2,6x1012 piecesM3x10
y1242, Inclined air filter adapter for HPI Baja and Carson Wild Attack GP, set
This 15° inclined adapter allows for easy access for filter servicing or installation of a precleaner like the Twinair filter skin. This beautifully machined part comes with all the hardware and gaskets needed.Fits all cars from the HPI Baja 5 series and Carson Wild Attack GP.The adapter must be used with the stock airfilter, but replaces the stock adapter plate. Installation of other filters is not possible, but not necessary either since the HPI filter is one of the best filters on the market.The special design improves airflow for better performance.Outer diameter 64 mmInner diameter 54 mmOverall height 27 mm
y1587 Conversion kit to electric drive for HPI Baja 5B and Carson Wild Attack
The conversion kit contains all mechanical parts (no electric motor, esc and batteries) you need to convert a Carson Wild Attack or HPI Baja 5B to electric drive.Brushless motors from all common manufacturers with 56 - 58 mm diameter, about 100 - 115 mm motor can length, 700 - 850 KV and 8 mm output shaft will fit. We recommend the TT56112/700 Top Tuning Monster Brushless Motor 700 kV.For the esc,ZTW Beast 200A or other ESCs with similar dimensions and performance data are suitable.The battery box provides a total space of 180 x 84 x 50 mm for the batteries. Operation with 6S - 8S is recommended.The set contains: Battery and receiver box Complete aluminum motor mount Ball bearing for intermediate shaft Motor pinion Chassis struts and mounting plate for esc made of aluminum Extension cable for speed controller installation hardware Exploded view and assembly instructions
y0733 Big Scale-EXTREME, adjustable 3 - shoe clutch
With the Big Scale-EXTREME an adjustable clutch for very special requirements has been designed:For large-displacement enginesFor heavy or high traction cars (Losi, HPI)For modified performance enginesFor the demanding off-road useRapid wear of a clutch is a sign of constant slipping, even beyond engagement speed. In this case, the clutch does not transfer the applied torque.This is where the Big ScaleEXTREME sets a new standard.The new design of the "Extreme" prevents the centrifugal forces of clutch springs or lever side of the clutch shoes from counteracting the centrifugal force of the friction pad side even after engagement.As a result this clutch can transfer lots of power with minimal wear.The new design ensures that the centrifugal forces are transferred in full to the clutch lining. Precise engagement and disengagement even under high loads and inside of closed clutch bell carriers means no problem for this clutch.The clutch can be easily adjusted to the engagement speed through three set screws without clutch bell removal, so you can match the characteristics of your engine.The special clutch lining of the Big Scale-EXTREME is particularly wear-resistant and - especially in combination with a high-quality nitrited clutch bell (), guarantees for an exceptionally long service life! Contrary to the "Cross" or "Race" version there's no need to uninstall the clutch from the engine for maintenance. All parts are easily accessible from the front after removing the front plate.Please see the specifications tab for further information and handling advices!The regular price of the Big Scale-EXTREME is EUR 139.90
BJ208R/UCP Upper cap with balljoint for GPM HPI Baja, Carson Wild GP Attack shocks, 1 pce
Tuning / Replacement part for HPI Baja, Carson Wild GP Attack shocks for front and rear axle.
y0658/02 Narrow-Grip 462 type tires for Losi, HPI, FG, Carson and Co with 24 mm hex
Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available with 24mm hex for Losi, HPI Baja 5 and Carson GP Wild Attack series cars and they allready glued!To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims or for Losi and HPI models: y1406/01 - Big Digger y1407/01 - Cross Bond y1408/01- Over Lander y1409/01 - Giant Grip y1417/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.24 mm hex for Losi, HPI Baja 5 cars.Contents:2 pieces / 1 pair
SBJ160, GPM steel tie rod set for HPI Baja, Carson Wild GP Attack, set
Complete steering rods and tie rod between steering servo and servo saver with steel turnbuckles. Dimensions: Hole to hole: 120mm Total length: 135mm
y1016/100-02 Clutch housing Zenoah G320RC for HPI models
Genuine Zenoah G320RC clutch housing.Modified (milled) clutch housing for installation of a Zenoah G320RC engine in all HPI Baja 5 largescale cars.
BJ208R/SP Spring set for GPM HPI Baja, Carson Wild GP Attack rear shocks, set
The set includes springs for one shock!
2010-24 Mecatech brake piston
Genuine Mecatech spare/option part. Suitable for the Mecatech Crossbaja brake.Content:1 piece
ST0010 SPEED TEC weight-reduced balanced tuning flywheel
Genuine Speed-Tec spare/option part. SPEED TEC tuning flywheel for Zenoah G230/240/260/270/290/320 and Chung Yang engines (includes HPI Fuelie and Losi).The weight reduced (210 vs. 230 grams) flywheel enables the engine to accelerate faster and rev higher. The optimal balancing guarantees better endurance at lower fuel consumption!A durability approval exists!Contents:1 piece