TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece
TT1000 Top Tuning Electronic 20 Amp Bigscale high voltage 30 Volt switch
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
y0428 Extension cable universal180/300 mm
In case the servo cable is not long enough.Two selectable lengths:y0428/01 - 180 mmy0428/02 - 300 mm
AREA 5T-008/04 steering rod steel balls for 5T-008
Genuine Area spare/option part for set AREA 5T-008. Contents:2 pieces
AREA 5T-008/02 Flanged ball bearings and spacers for 5T-008 centerlink
Genuine Area spare/option part for the centerlink from AREA 5T-008. Content:2 x flanged ball bearings2 x steel spacers
AREA 5T-008/03 shoulder screws for 5T-008 centerlink
Genuine Area spare/option part for the centerlink from AREA 5T-008.Contents:2 pieces
AREA-5T-012/04 Screw set for AREA-5T-012
Genuine Area spare/option part.Replacement part for: AREA-5T-012 radio plate set for Losi 5ive-T and Mini.Content:1 piece
AREA 5T-008/05 servo linkage for 5T-008
Genuine Area spare/option part for set AREA 5T-008.Contents:2 x ball joint with steel balls1 x turnbuckle1 x M4 mm threaded rod
y0428/03 Extension cable universal
In case the battery cable is not long enough.Contents:1 piece
AREA 5T-008/01 aluminum centerlink for 5T-008
Genuine Area spare/option part for set AREA 5T-008.Content:1 piece
AREA-5T-012/02-01
Genuine Area spare/option part.The plate fits Losi stock servos.Replacement part for: AREA-5T-012 radio plate set V3 for Losi 5ive-T and Mini.Content:1 piece