Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all accessories (see also our pictures) required for installation.One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline Also suitable for electric models, but in conjunction with aluminum axle y0932 Bleeding instructionsDimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set

Genuine FG spare/option part.The set contains FG no.: 6042/05, 6044/05, 7041/05 and 8456/05. Is used to optimize the rear brake (FG no. 7497).Contents:1 set

Genuine FG spare/option part.Improved rear brake for Marder, Beetle Off-Road, Beetle On-Road and Pajero as well as EcoLine, not for Formula 1. Big epoxy brake disk (diameter 52 mm) for more brake power. Gear carrier is not included in the set. Only in connection with 7039/01or 7474.Contents:1 set

Low priced retrofitable front axle disk brake for all FG 1:5, 1:6, Off-Road 2WD and all 4WD models. also suitable for the 2-damper front axle and the Mono-Shock axle. The disk brake prevents a breaking-out of the rear, has a very sensitive adjustment and is optically very effective. You are able to run this disk brake with the gas servo, but make sure the servo has a minimum regulating power of 6kg. We deliver the disk brake without uprights. Link to the part scout!Content 6020 8093 6105/05 8455 8457/02 8458 8459/01 8461 8461/01 8462/01 8462/02 8462/06 8462/07 8462/05 8463 8464/01 8465

Genuine Losispare/option part. Mechanical brake for retrofitting in an electric powered Losi 5ive-B or 5ive-T 2.0. An additional servo and a 3-channel remote control are required.If you run the maximum operating voltage approved for an ESC, there is a risk - especially in large scale cars - that under certain circumstances the reverse currents generated by the motor when braking will destroy the esc.For this reason, we recommend using a mechanical brake (as with gas powered vehicles).Please note that Reverse is no longer possible with this configuration!In the ESC settings, you must select the Forward/Brake operating mode. The brake by the controller must be deactivated or set to the lowest possible value. For this job a program card suitable for the ESC is usually required!Set includes: TLR252011 TLR Brake Disc, Pad and Screw Set 5ive-B LOSB3230 Losi Brake Cams & Bushings 5T, TLR 5ive-B and Mini LOSB5901 Losi Throttle/Brake Linkage Set 5T, TLR 5ive-B and Mini Servo mount for throttle / brake servoLosi Servo HS901T Contents:1 set

Low-priced retrofitable disk brake for the rear wheels. Suitable for all 1:5 and 1:6 models and Race-Trucks. In connection with the front disk brake very high brake power, optically very effective. We recommend to steer over 2 servos if you install the front and rear disk brake. We deliver the disk brake without uprughts.Contents:1 piece

Mecatech twin piston hydraulic brakeTwin piston hydraulic brakes with Epoxi rotors and steel brake pads for optimized braking performance. The master cylinders feature a volume compensation.Fits FG Evo 04 - 08, Mecatech FW01, Competition 07 - 08, Sportsline 08 and with pedestal in every FG offroad cars (buggy / monster / stadium with original FG 700 ml fuel tank).The brake fits without any further accessories on FG Evo-models which are equipped with the a-arms no. 1100/10 respectively 1100/11When running wheel squares with Seeger ring, the ring has to be removed.On FG Evo-models which are equipped with the a-arms no. 1100/05 respectively 1100/06, the brake has to be filled before the installation. In addition the ventilation nipple of the brake must be exchanged against the venting valve no. y0309Pedestal for installation for all FG Offroad-models: Mecatech twin piston hydraulic brake

Mecatech twin piston hydraulic brakeIt is the best brake for RC cars in the large model range from teh Mecatech FW01 and can be retrfitted to many FG models.Best quality for the highest demands!- The main brake cylinder is equipped with volume compensation and ensures constant braking pressure with good metering.- The brake calipers have a double-piston system and steel brake pads and teh epoxy brake discs ensure short braking distances. Installation instructions!Suitable for all FG off-road 2WD/4WD models (Leopard basis) and also for all FG off-road 2WD and 4WD models on a Marder basis with a laterally angled chassis such as (buggy / monster / stadium with original FG 700 ml tank) only with mounting base.Mounting base for all FG Offroad models:9438/01 a> Aluminum wheel chockWhen installing in an FG Evo 2020, 2020.1, 2020.2 and FG Raceline you need the adapter plates y1515.For FG Evo 12-14 models with the wishbone no. evo-2013-1-st-.html">1100/10 or 1100/11, the brake fits without additional accessories.For FG Evo 04-08 models with the wishbones no. evo-04-08-1st-.html">1100/05 or 1100/05, the brake must be 1100/05.When running wheel squares with Seeger ring, the ring has to be removed.Not for FG Formula 1 models.

Normal price: 249,90 EUR Tuning front disk brake system for the HPI Baja 5B/SS/5T/5sc, the conversion kit includes all necessary parts. The brake includes the finest parts available for a cable brake and has the following features: * uses existing mounting points for all parts * brake pads and 70 mm diameter stainless rotors made by RS-5, the best performing combination available * hardened stud bolts for the brake pads * billet brake levers, no tweak and best transfer of servo power * ultraflex bowden cables * brake cams run in hardened steel bushings and brass guide plates (miniature bearings don't last in offroad cars) * billet alloy bowden cable support block with adjustment screws * billet alloy bowden cable mounts at the calipers * pre-assembledOn a 5T the stud bolts which hold the brake pads will interfere with the ribs in the rim. However, modifying the rim or swapping the stud bolts for long csh screws allows for installation on a 5T.Spare parts for this brake as a PDF-file with spare part numbersWe highly recommend the installation of a stronger throttle servo to take full advantage of this brake system. The is an excellent choice.

Genuine FG spare/option part. Front tuning disk brake for all FG 1:5 models and Race-Trucks, the current version from Evo, with 2-damper front axle and the Mono-Shock axle except Formular 1 and Leopard.The disk brakes prevent a breaking-out of the rear, have a very sensitive adjustment and are optically very effective. You can run the front disk brake with the gas servo, but make sure the servo has a minimum regulating power of six kilograms. We recommend to steer over two servos if you install front and rear disk brake. We deliver the disk brakes without uprights. In combination with the rim 6105/01 also suitable for Marder, Beetle and Pajero.Additional equipment for front and rear tuning disk brake:Flexible bowden cablesAlloy guiding plate with ball bearingSteel bushStud bolt for brake liningLasered tuning disk brakeCompetition brake lining

Genuine FG spare/option part. The rear disk brake is suitable for 1:5 models, Race-Trucks, the current version from Evo, 1:6 Off-Road and Monster models. The disk brakes prevent a breaking-out of the rear, have a very sensitive adjustment and are optically very effective. You can run the front disk brake with the gas servo, but make sure the servo has a minimun regulating power of six kilograms. We recommend to steer over two servos if you install front and rear disk brake. We deliver the disk brakes without uprights. In combination with the rim 6105/01 also suitable for Marder, Beetle and Pajero.Additional equipment for front and rear tuning disk brake:8472/01 Flexible bowden cables8474/05 Alloy bowden cable holder8469 Alloy guiding plate with ball bearing8479 Steel bush8448 Stud bolt for brake lining8458/02 Lasered tuning disk brake8457/03 Competition brake lining

Tuning disk brake for front axle. Suitable for Marder and Beetle. With the tuning disk brake you get a higher brake action.

Complete pre-assembled set front disc brakes for FG Marder, FG Off-Road Buggy and for Carson / Smartech Attack / Comanche / UNO / Monster Truck / CRT / CPT / Super Attack / Evo Attack / Spider / Big Attack , fits Conrad Big Pyro as well.For mounting in a Gas Blaster you must change you front shock mount and the front body shell holder, look at the pictures. Includes:- brake system with linkage- uprights- bearings- longer axle shafts- wider square drivesNo additional parts needed.

Genuine FG spare/option part. The rear disk brake is suitable for 1:5 models, Race-Trucks, the current version from Evo, 1:6 Off-Road and Monster models. The disk brakes prevent a breaking-out of the rear, have a very sensitive adjustment and are optically very effective. You can run the front disk brake with the gas servo, but make sure the servo has a minimun regulating power of six kilograms. We recommend to steer over two servos if you install front and rear disk brake. We deliver the disk brakes without uprights. In combination with the rim 6105/01 also suitable for Marder, Beetle and Pajero.Additional equipment for front and rear tuning disk brake:8472/01 Flexible bowden cables8474/05 Alloy bowden cable holder8469 Alloy guiding plate with ball bearing8479 Steel bush8448 Stud bolt for brake lining8458/02 Lasered tuning disk brake8457/03 Competition brake lining

Genuine FG spare/option part. Content:1 set

Tuning disk brake for front axle. Suitable for Monster-Truck, Monster Beetle Pro and Stadium-Truck. With the tuning disk brake you get improved braking preformance.This tuning version includes ultra flex brake cables, alloy cable mounts, ballraced alloy cam guide plates, stud bolts, competition brake pads and rotors.

Retrofitable bowden cable disk brakes for Formula 1 Sportsline and Competition models. Essentially improved brake power compared to the standard brake, sensitive adjustment.

Additional equipment of the front tuning disk brake compared to disk brake :- Flexible bowden cable - Alloy bowden cable holder- Alloy guiding plate with ball bearing- Steel bearing bush- Stud bolt for brake lining- Tuning brake disk- Competition brake lining

Genuine Hyde's spare/option part.Replacement brake pads for the Mr. Hyde's brake no. 1200315.Contains:2 pieces

Genuine FG spare/option part. Content:1 set

Front disc brake hop-up for monster and stadium models with dual shock front axle. Significantly improved braking preformance without rear axle lock-up.Attention!!Can only be installed in connection with the alloy uprights .

Retrofitable bowden cable disk brakes for Formula 1 Sportsline and Competition models. Essentially improved brake power compared to the standard brake, sensitive adjustment.

Genuine FG spare/option part. Front disc brake hop-up for Leopard and Pajero.Contents:1 set

Additional equipment of the front tuning disk brake compared to disk brake :- Flexible bowden cable - Alloy bowden cable holder- Alloy guiding plate with ball bearing- Steel bearing bush- Stud bolt for brake lining- Tuning brake disk- Competition brake lining