7497 FG Rear brake 97 for 1:5 and 1:6
€52.50
Available
Product information "7497 FG Rear brake 97 for 1:5 and 1:6"
Improved rear brake for Marder, Beetle Off-Road, Beetle On-Road and Pajero as well as EcoLine, not for Formula 1. Big epoxy brake disk (diameter 52 mm) for more brake power. Gear carrier is not included in the set.
Only in connection with 7039/01or 7474.
Contents:
- 1 set
Login
Accessories / Spare parts
Genuine FG spare/option part. Suitable for all FG 1:5 and 1:6 2WD and 4WD models. Best fitting of ball bearing seat and distance of gear shaft, non-twisting. To mount this gear plate into the models Marder, Beetle, Beetle On-Road, Pajero and Monster the rear brake 7040/01 is needed.Bearing seatsClutch bell: 22 x 6 mmLayshaft: 19 x 7 mmContent:1 piece
Alternatives
Genuine FG spare/option part.The set contains FG no.: 6042/05, 6044/05, 7041/05 and 8456/05. Is used to optimize the rear brake (FG no. 7497).Contents:1 set
Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).Only suitable for models with 18 mm square mount.The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all accessories (see also our pictures) required for installation.One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline Also suitable for electric models, but in conjunction with aluminum axle y0932 Bleeding instructionsPlease enquire whether this brake is suitable for your model. Dimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set
Customers also bought
Genuine FG spare/option part. Suitable for all FG 1:5 and 1:6 2WD and 4WD models. Best fitting of ball bearing seat and distance of gear shaft, non-twisting. To mount this gear plate into the models Marder, Beetle, Beetle On-Road, Pajero and Monster the rear brake 7040/01 is needed.Bearing seatsClutch bell: 22 x 6 mmLayshaft: 19 x 7 mmContent:1 piece
Genuine FG spare/option part. This spacer bushing goes into the gear plate between the two clutch bell bearings, preventing them from binding when installing the pinion on the clutch bell.Contents:1 piece
Spare part for 7348Outer diameter 43 mmHeight 20 mm
Small alloy engine mount.Suitable for Marder, Beetle, Pajero and Monster with CY / Zenoah G230/240/260/270/290 engine.
Genuine HT spare/option part.This adaptor allows you to install all MadMax/HPI tire/rim combinations on FG, Carso, Smartech 2WD/4WD and other cars with the same wheel shaft configuration. Losi 5ive tires can be used as well, but they hey have to be mounted on MadMax/HPI rims because Losi rims are too thick at the center. The adapter is drilled for 8 mm wheel shafts (FG, Smartech/Carson and many more!), hex size of wheel drive and wheel nut is 24 mm hex with M18x1.0 thread (same as HPI).Please note:FG wheel shafts come with either M6 or M8 thread size. It can even happen that a vehicle has different thread sizes front and rear! Therefore, please make sure which version is required before placing an order.Converting your car takes only a couple of minutes with this easy to install adaptor. just see picture "installation instruction" for a schematic installation.Contents:2 pieces
Customers also viewed
Genuine FG spare/option part. The set will shipped without gear carrier plate. Contents:1 set
Genuine FG spare/option part.The set contains FG no.: 6042/05, 6044/05, 7041/05 and 8456/05. Is used to optimize the rear brake (FG no. 7497).Contents:1 set
Genuine FG spare/option part. Front tuning disk brake for all FG 1:5 models and Race-Trucks, the current version from Evo, with 2-damper front axle and the Mono-Shock axle except Formular 1 and Leopard.The disk brakes prevent a breaking-out of the rear, have a very sensitive adjustment and are optically very effective. You can run the front disk brake with the gas servo, but make sure the servo has a minimum regulating power of six kilograms. We recommend to steer over two servos if you install front and rear disk brake. We deliver the disk brakes without uprights. In combination with the rim 6105/01 also suitable for Marder, Beetle and Pajero.Additional equipment for front and rear tuning disk brake:Flexible bowden cablesAlloy guiding plate with ball bearingSteel bushStud bolt for brake liningLasered tuning disk brakeCompetition brake lining
Small alloy engine mount.Suitable for Marder, Beetle, Pajero and Monster with CY / Zenoah G230/240/260/270/290 engine.
Genuine FG spare/option part. Suitable for all FG 1:5 and 1:6 2WD and 4WD models. Best fitting of ball bearing seat and distance of gear shaft, non-twisting. To mount this gear plate into the models Marder, Beetle, Beetle On-Road, Pajero and Monster the rear brake 7040/01 is needed.Bearing seatsClutch bell: 22 x 6 mmLayshaft: 19 x 7 mmContent:1 piece
Genuine FG spare/option part. For gear plates 7039/1 oder 7474. Only for use with single brake disc on the layshaft.Contents:1 piece
Genuine Losispare/option part. Mechanical brake for retrofitting in an electric powered Losi 5ive-B or 5ive-T 2.0. An additional servo and a 3-channel remote control are required.If you run the maximum operating voltage approved for an ESC, there is a risk - especially in large scale cars - that under certain circumstances the reverse currents generated by the motor when braking will destroy the esc.For this reason, we recommend using a mechanical brake (as with gas powered vehicles).Please note that Reverse is no longer possible with this configuration!In the ESC settings, you must select the Forward/Brake operating mode. The brake by the controller must be deactivated or set to the lowest possible value. For this job a program card suitable for the ESC is usually required!Set includes: TLR252011 TLR Brake Disc, Pad and Screw Set 5ive-B LOSB3230 Losi Brake Cams & Bushings 5T, TLR 5ive-B and Mini LOSB5901 Losi Throttle/Brake Linkage Set 5T, TLR 5ive-B and Mini Servo mount for throttle / brake servoLosi Servo HS901T Contents:1 set