y0056 HT - Carson Wild GP Attack and HPI Baja 5B/SS/5T/5sc premium front disk brake
Product number:
y0056
EAN:
4058575014843
Product information "y0056 HT - Carson Wild GP Attack and HPI Baja 5B/SS/5T/5sc premium front disk brake"
Normal price: 249,90 EUR
Tuning front disk brake system for the HPI Baja 5B/SS/5T/5sc, the conversion kit includes all necessary parts. The brake includes the finest parts available for a cable brake and has the following features:
* uses existing mounting points for all parts
* brake pads and 70 mm diameter stainless rotors made by RS-5, the best performing combination available
* hardened stud bolts for the brake pads
* billet brake levers, no tweak and best transfer of servo power
* ultraflex bowden cables
* brake cams run in hardened steel bushings and brass guide plates (miniature bearings don't last in offroad cars)
* billet alloy bowden cable support block with adjustment screws
* billet alloy bowden cable mounts at the calipers
* pre-assembled
On a 5T the stud bolts which hold the brake pads will interfere with the ribs in the rim. However, modifying the rim or swapping the stud bolts for long csh screws allows for installation on a 5T.
Spare parts for this brake as a PDF-file
with spare part numbers
We highly recommend the installation of a stronger throttle servo to take full advantage of this brake system. The is an excellent choice.
Tuning front disk brake system for the HPI Baja 5B/SS/5T/5sc, the conversion kit includes all necessary parts. The brake includes the finest parts available for a cable brake and has the following features:
* uses existing mounting points for all parts
* brake pads and 70 mm diameter stainless rotors made by RS-5, the best performing combination available
* hardened stud bolts for the brake pads
* billet brake levers, no tweak and best transfer of servo power
* ultraflex bowden cables
* brake cams run in hardened steel bushings and brass guide plates (miniature bearings don't last in offroad cars)
* billet alloy bowden cable support block with adjustment screws
* billet alloy bowden cable mounts at the calipers
* pre-assembled
On a 5T the stud bolts which hold the brake pads will interfere with the ribs in the rim. However, modifying the rim or swapping the stud bolts for long csh screws allows for installation on a 5T.
Spare parts for this brake as a PDF-file
with spare part numbers
We highly recommend the installation of a stronger throttle servo to take full advantage of this brake system. The is an excellent choice.
Login
Accessories / Spare parts
Top quality epoxy P-R-M Race brake discs with 10 dirt slots for removing dirt and abrasion, which will be transferred to the outside by the discs rotation. The epoxy P-R-M Race brake disc provides an optimal deceleration of the car without the unwanted fading (poor braking performance due to increased heat buildup)! The best braking action when using the epoxy P-R-M Race brake disc is achieved by the combination of the epoxy brake discs and steel brake pads (8456 or y19218). The epoxy P-R-M Race brake discs fit mechanical front and rear brakes on FG / Smartech / Carson cars with brake pads 8456 recommended for these applications.1 pair (2 pieces) Dimensions: Outer diameter: 60 mm Thickness: 2 mmsocket for 18 mm square wheel drive
Genuine FG spare/option part. New competition brake lining with good braking characteristics and low wear. Glued on a steel plate.Spare part for: 6250/05, 6250/06, 8450/05, 8452/05, 10452, 10453 and y0056 HT - Baja 5B/SS premium front disk brake.Measures:Length approx. 50 mmWidth approx. 10 mmThickness approx. 5.5 mmMounting hole distance 40 mmContents:4 pieces
Customers also bought
BUILD YOUR OWN ORIGINAL,AUTHENTIC HPI BAJA 5BHPI large scale fans, we have heard you! The one and only original HPI Baja 5B is BACK and ready for you to build from the ground up! The HPI SBK collection of Self Build Kits grows with the addition of not just one, but TWO 1/5th scale HPI kits! Fans of large scale off-road RC will be super excited to build their own gas-powered 1/5th scale Buggy with the HPI Baja 5B Self Build Kit!When the HPI Baja 5B buggy was first introduced, large scale RC was very expensive and quite difficult for the average RC hobbyist to experience. Using highly durable parts and innovative design features, HPI brought large scale off-road to new enthusiasts and ushered in a new, BIGGER era of RC!Now, YOU can build and own the legend! Experience the thrill and excitement of building a car which ends up being over 80cm (nearly 32 inches) long and weighing nearly 10kg (over 21 lb)! Just install your own engine and electronics as you build the HPI Baja 5B and you'll be ready for any adventure that comes your way!With extra-tough drivetrain parts like the viscous torque differential, super-durable composite spur gear with internal damping and all-metal drivetrain, the HPI Baja 5B is ready for your 23-32cc 2-stroke engine so you can experience the joy of gas-powered RC and up to 30-minute runtimes!The HPI Baja 5B is also equipped with extra-big and super-tough suspension parts, featuring awesome HPI durability! With its expertly designed molded composite suspension plus extra-long adjustable HD shocks, and massive high impact nylon 3-piece beadlock wheels, the Baja 5B is ready for full-speed racing on any off-road circuit!The 4mm thick 6061 aluminum monocoque chassis gives the HPI Baja 5B the classic desert racing buggy look. Precisely bent into shape for maximum strength, the chassis provides the mounting points for the engine and suspension, forming the backbone of the car. Precise steering is provided by a dual-bellcrank rack and cam-type servo saver. Aluminum parts are anodized in cool gunmetal and the classic Baja desert racer clear polycarbonate body is included in the SBK kit, ready for your custom racing scheme!The Baja 5B SBK is a great addition to your HPI collection, as well as a fabulous introduction to large scale buggies!RACING CHASSIS DESIGN & LAYOUTThe narrow channel chassis made from rigid 4mm 6061 aircraft aluminum and gives the HPI Baja 5B a classic desert racing buggy look and extreme stiffness and durability. The U-shaped chassis is protected at the rear with a thick plastic skid plate for extra protection to the motor and drivetrain.The tube roll cage is made of high impact nylon and topped with a real aluminum roof to carry on the classic looks. The roll cage is fully functional and protects the motor and internals from crash damage. The roll cage, radio box, body panels, wing, undertray and gear case are all mounted with fast access clips for easy maintenance. To finish you need: Engine with clutch and exhaust Remote control with servos and receiver battery Charger Two cans of Lexan paint Features Summary Unassembled 1/5th scale Off-Road Buggy Ready for your 23-32cc RC engine Ready for your electronics Enclosed radio box Baja desert racing body design Adjustable HD shock absorbers Monocoque chassis Low CG for superior handling Long travel suspension Viscous torque oil-filled gear differential All-terrain tires Beadlock wheels with metal insert hubs Aluminum rear shock tower Hard plastic skid plates Adjustable rear wing Quick access to all critical maintenance points Dual bellcrank steering Cam type servo saver Race spec Hex socket hardware Gunmetal anodizing Full set of rubber-sealed ball bearings Chassis Specifications Overall Length 817mm Height: 255mm Width: Front - 460mm; Rear - 480mm Tire Track (to center of tires): Front - 395mm; Rear - 400mm Wheelbase: 570mm Ride Height: 76mm Suspension Travel: Front - 95mm; Rear - 100mm Weight: 9.6kg (21.3lb) Adjustable Camber: front - shims; rear - screw Front caster: adjustable with shim 22 / 25.5* / 29 degrees (* stock) Toe-in: Front adjustable with tie rod; Rear adjustable with inserts 0-4 degrees (3 degrees stock set-up) Aircraft aluminum 6061 T6 monocoque chassis Double wishbone suspension with adjustable roll center F/R Drive system: HD metal gears with sealed gear box (8.382:1 gear ratio) Differential: viscous torque control with 4 pinion gears; sealed diff case with silicone oil Shock absorber: HD Aluminum coilover shock absorber with fully adjustable preload collar Wheel type: 3-piece beadlock design, high impact nylon material with inset heavy-duty metal hex hub
26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:Quantity of cylinder mounting bolts increased from 2 to 4Improved strength of crankcaseAdded additional bearing on the PTO (clutch) side of crankshaftRedesigned shape of cylinder finsDimension of air intake port is 5% widerNew carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.Content:5315 Clutch block carrier5315/01 Screw for carrier7318 Dowel screw for clutch blocksy1419 Sinter clutchy1419/01 Clutch springs for Sinter clutch
y2009 TopTuning Digital pro 25 kg is a digital large scale servo with very robust metal gears.It offers a lot of power at a good speed and has a metal housing.Its installation dimensions fit directly as a throttle / brake servo for FG, HPI and various other models! Top Tuning Bigscale 25kg - servo for throttle / brake Dimensions identical to: FG 6598 t1005 10 kg Spectrum Z590 6 kg HPI SF 20W 7 kg y2007 Digital Bigscale 30 kg y2008 Digital Bigscale 20 kg Technical data: Classification: universal servo Dimensions LxWxH (mm): 40.5 x 20 x 39 mm Operating voltage: 6 volts / 7.4 volts Torque: (Ncm): 220/250 Speed (sec / 60 °): 0.14 / 0.12 Number of ball bearings: 2 Servo gear: metal gears Seals: 3 (splash-protected) Silicone cable: with universal plug, 300 mm long Weight: 62.5 grams Steel output shaft 25T spline Content: 1 piece of TopTuning Digital pro servo 25 kg 1 piece double sided servo arm 53 mm total 1 piece of 35 mm single sided servo arm 4 pieces of guide sleeves 4 pieces of rubber grommets 4 pieces of fastening screws
CYS S0650, a digital large scale servo with very robust steel gears. It offers a lot of power at good speed. Its a direct fit for cars like Losi 5ive and DBXL, UFRC Growler GX1, FG and so on.Technical data: Operating voltage: 6V-7.4V Operating speed (6.0 V): 0.13 s / 60 degrees Operating speed (7.4 V): 0.11 s / 60 degrees Holding torque (6.0V): 470 Ncm holding torque (7.4V): 539 Ncm Cable: Universal/JR connector, approx. 300mm Gear material: 1st stage brass, all others steel Bearing: 2 x ball bearing Size: 66 x 30 x 56mm Weight: 204 grams Double sided servo arm 68mm length Guide sleeve 4 pieces Mounting screws 4 pieces Mounting screws for servoarm 1 piecesContents:1 piece
Similar products
Tuning / Replacement part for HPI Baja, Carson Wild GP Attack shocks for front and rear axle.
Fully assembled and factory filled with 1.000 viscosity silicone oil. Including springs which can be adjusted via a threaded collar. The excellent quality GPM shocks fit all cars of the HPI Baja 5 series, Carson Wild GP Attack and feature an extremely massive 7 mm rod. The GPM shocks cases and rod ends are completely made of aluminum and equipped with replaceable bushings at the upper and lower mounting points.The external volume control is more efficient than built-in versions with membrane or foam element. Compared with the technically similar solution of a floating balance piston inside of the shock absorber body there is the advantage that no length of the shock absorber is needed for the volume compensation. Furthermore the additional housing surface of the equalizing chamber helps in cooling the oil. Dimensions (front):distance between mounting holes (extended): 187 mm travel: 62 mm li> Outer diameter: 28 mm Mounting specifications: top and bottom 12 mm wide ball mount with 4 mm bore The GPM shocks are filled with 1.000 viscosity silicone oil. For a firmer setting 1.500 or higher viscosity silicone oil is recommended. If a softer setup is required, 900 or lower viscosity oil should be used.
Fully assembled and factory filled with 1.000 viscosity silicone oil. Including springs which can be adjusted via a threaded collar. The excellent quality GPM shocks fit all cars of the HPI Baja 5 series, Carson Wild GP Attack and feature an extremely massive 7 mm rod. The GPM shocks cases and rod ends are completely made of aluminum and equipped with replaceable bushings at the upper and lower mounting points.The external volume control is more efficient than built-in versions with membrane or foam element. Compared with the technically similar solution of a floating balance piston inside of the shock absorber body there is the advantage that no length of the shock absorber is needed for the volume compensation. Furthermore the additional housing surface of the equalizing chamber helps in cooling the oil. Dimensions:distance between mounting holes (extended): 207 mm travel: 69 mm li> Outer diameter: 28 mm Mounting specifications: top and bottom 12 mm wide ball mount with 4 mm bore The GPM shocks are filled with 1.000 viscosity silicone oil. For a firmer setting 1.500 or higher viscosity silicone oil is recommended. If a softer setup is required, 900 or lower viscosity oil should be used.
Tuning / Replacement part for HPI Baja, Carson Wild GP Attack Stoßdämpfer.Set contains one each piston and shaft guide bushing. Fits for front and rear axle.
Shock body rear for GPM HPI, Carson Wild GP Attack shocks.High quality cnc machined parts made by GPM Racing Products from high strength billet aluminum.
Shock body front for GPM HPI, Carson Wild GP Attack shocks.High quality cnc machined parts made by GPM Racing Products from high strength billet aluminum.
Replacementpart for GPM HPI Baja, Carson Wild GP Attack shocks no. BJ186F
Replacementpart for GPM HPI Baja,Carson Wild GP Attack shocks no. BJ208Rnew, M5 thread size, BJ208R/SH
Tuning / Replacement part for HPI Baja, Carson Wild GP Attack shocks front and rear.High quality cnc machined parts made by GPM Racing Products from high strength billet aluminum. Fits for HPI Baja.O-ring included.Fits original HPI shocks as well.
Tuning / Replacement part for HPI Baja, Carson Wild GP Attack. High quality cnc machined parts made by GPM Racing Products from high strength billet aluminum. Fits for HPI Baja front and rear axle .
Alternative product to HPI Order No. H86445.High quality cnc machined parts made by GPM Racing Products from high strength billet aluminum. Fits for HPI Baja front and rear axle.
The set includes springs for one shock!
Customers also viewed
%
With the Carson Wild Attack almost everything for driving (!) is included! The only exception: The fuel mixture from the gas station. (Recommended oil for mixing: y0813/02).The model includes the completely installed 2.4 GHz remote control, incl. transmitter alkalines, as well as a fail-safe system (automatic engine cut-off in case of possible malfunctions!), 20kg throttle servo and 35 kg steering servo, as well as a 2.000 mAh 6V receiver battery with charger and a tool set. Furthermore a spare air filter element and a special mixing canister. A detailed multilingual manual is also included. Here you will find an excellent, about 7 minutes duration introduction video to the Carson Wild Attack, which allows even the absolute novice for RC-Carswith combustion engine, the uncomplicated, problem-free entry: Technical details: approx. 70 km/h top speed0 - 70 km/h approx. 2.5 seconds With one tank of gas (700ccm) approx. 40 minutes driving time29cc engine, with pull starterSound reducing tuned pipe exhaust system2-shoe cltch with steel clutch bellA steel differential.Aluminium shocks, dust protectedbead-lock rims with off-road tyresaluminium rim driveradjustable rear wingCompletely ballraced 2WD drivetrain Water protected receiver boxventilated double disc brakealuminium chassis
BUILD YOUR OWN ORIGINAL,AUTHENTIC HPI BAJA 5BHPI large scale fans, we have heard you! The one and only original HPI Baja 5B is BACK and ready for you to build from the ground up! The HPI SBK collection of Self Build Kits grows with the addition of not just one, but TWO 1/5th scale HPI kits! Fans of large scale off-road RC will be super excited to build their own gas-powered 1/5th scale Buggy with the HPI Baja 5B Self Build Kit!When the HPI Baja 5B buggy was first introduced, large scale RC was very expensive and quite difficult for the average RC hobbyist to experience. Using highly durable parts and innovative design features, HPI brought large scale off-road to new enthusiasts and ushered in a new, BIGGER era of RC!Now, YOU can build and own the legend! Experience the thrill and excitement of building a car which ends up being over 80cm (nearly 32 inches) long and weighing nearly 10kg (over 21 lb)! Just install your own engine and electronics as you build the HPI Baja 5B and you'll be ready for any adventure that comes your way!With extra-tough drivetrain parts like the viscous torque differential, super-durable composite spur gear with internal damping and all-metal drivetrain, the HPI Baja 5B is ready for your 23-32cc 2-stroke engine so you can experience the joy of gas-powered RC and up to 30-minute runtimes!The HPI Baja 5B is also equipped with extra-big and super-tough suspension parts, featuring awesome HPI durability! With its expertly designed molded composite suspension plus extra-long adjustable HD shocks, and massive high impact nylon 3-piece beadlock wheels, the Baja 5B is ready for full-speed racing on any off-road circuit!The 4mm thick 6061 aluminum monocoque chassis gives the HPI Baja 5B the classic desert racing buggy look. Precisely bent into shape for maximum strength, the chassis provides the mounting points for the engine and suspension, forming the backbone of the car. Precise steering is provided by a dual-bellcrank rack and cam-type servo saver. Aluminum parts are anodized in cool gunmetal and the classic Baja desert racer clear polycarbonate body is included in the SBK kit, ready for your custom racing scheme!The Baja 5B SBK is a great addition to your HPI collection, as well as a fabulous introduction to large scale buggies!RACING CHASSIS DESIGN & LAYOUTThe narrow channel chassis made from rigid 4mm 6061 aircraft aluminum and gives the HPI Baja 5B a classic desert racing buggy look and extreme stiffness and durability. The U-shaped chassis is protected at the rear with a thick plastic skid plate for extra protection to the motor and drivetrain.The tube roll cage is made of high impact nylon and topped with a real aluminum roof to carry on the classic looks. The roll cage is fully functional and protects the motor and internals from crash damage. The roll cage, radio box, body panels, wing, undertray and gear case are all mounted with fast access clips for easy maintenance. To finish you need: Engine with clutch and exhaust Remote control with servos and receiver battery Charger Two cans of Lexan paint Features Summary Unassembled 1/5th scale Off-Road Buggy Ready for your 23-32cc RC engine Ready for your electronics Enclosed radio box Baja desert racing body design Adjustable HD shock absorbers Monocoque chassis Low CG for superior handling Long travel suspension Viscous torque oil-filled gear differential All-terrain tires Beadlock wheels with metal insert hubs Aluminum rear shock tower Hard plastic skid plates Adjustable rear wing Quick access to all critical maintenance points Dual bellcrank steering Cam type servo saver Race spec Hex socket hardware Gunmetal anodizing Full set of rubber-sealed ball bearings Chassis Specifications Overall Length 817mm Height: 255mm Width: Front - 460mm; Rear - 480mm Tire Track (to center of tires): Front - 395mm; Rear - 400mm Wheelbase: 570mm Ride Height: 76mm Suspension Travel: Front - 95mm; Rear - 100mm Weight: 9.6kg (21.3lb) Adjustable Camber: front - shims; rear - screw Front caster: adjustable with shim 22 / 25.5* / 29 degrees (* stock) Toe-in: Front adjustable with tie rod; Rear adjustable with inserts 0-4 degrees (3 degrees stock set-up) Aircraft aluminum 6061 T6 monocoque chassis Double wishbone suspension with adjustable roll center F/R Drive system: HD metal gears with sealed gear box (8.382:1 gear ratio) Differential: viscous torque control with 4 pinion gears; sealed diff case with silicone oil Shock absorber: HD Aluminum coilover shock absorber with fully adjustable preload collar Wheel type: 3-piece beadlock design, high impact nylon material with inset heavy-duty metal hex hub
Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all, necessary for installation, accessories (see also our pictures)One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline and E (in connection with alloy front uprights y0932Dimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set
The new TT0900 electric starter is pre-assembled and fits a wide range of models including the Losi 5ive-T, 5ive Mini and DBXL, most FG models, HPI-Baja / Wild Attack series etc. The TT0900 electric starter can be started with the remote control (free channel required!). The new TT0900electric starter has much more power than the previous Electric starter thanks to the brushless motor and higher voltage. The popular Zenoah G320 is no longer a problem. It also no longer uses a one-way bearing, which clearly increases reliability. Also the installation space has been noticeably reduced by the motor and a planetary gearbox.The starter components to be fitted weigh about 666 grams plus the battery.For mounting the starter, the flywheel on the engine is replaced by the version with spring-loaded pawls included in the delivery. The tools required for this, piston stopper and flywheel puller, are also included in the delivery.For the 3rd channel the transmitter should have a switch with two positions (momentary switch preferred) or a controller. An additional channel is required for a remote engine killswitch. A killswitch is included in the scope of delivery, but a real fail-safe module such as TT0990 offers higher safety. A possibly already existing failsafe module can also be used.Due to the splitting of the functions engine start and engine stop on two channels, no more compatibility problems with different remote controls are to be expected, only the availability of free channels matters.A 3S LiPo battery is required as the power source.In the shops options menu, we offer a special battery with a more compact design (5,600 mAh/30C, 110 x 49 x 34 mm) which makes installation usually easier in many cars, as well as a battery with standard dimensions (3,900 mAh/60C, 135 x 45 x 25 mm). Of course, other 3S batteries can also be used at your own discretion, but the load capacity (capacity x C-rate) should be on a similar or higher level.Please note that we cannot ship batteries to countries outside the European Union!Since the starter unit can be mounted vertically or horizontally and the brushless starter motor is very small, almost all air filters and most tuned pipe systems can be used.Notes regarding necessary modifications known to us for mounting the starter depending on the vehicle: FG 4wd onroad Rear r/h plastic body mount, depending on position, slightly modified or relocated FG 2wd onroad horizontal engine No modifications Mecatech FW01 No modifications FG 4wd Buggy sportsline Depending on the body shell, minor trimming is required. FG 2wd Buggy current chassis Depending on the body shell, minor trimming is required. FG 2wd Marder (old chassis) Starter fits without modifications to the chassis plate. However, the body shell has to be cut out a bit more seriously in the area of the starter. A repositioning of the rear r/h body mount is recommended. FG Monster Cut the r/h side panel slightly and add a flat area to the aluminum tube which supports the panel on the engine Losi 5ive-B Depending on the tuned pipe, mount starter with motor on top or on the l/h side. Losi 5ive-B Mount the starter motor on the l/h side, space for the tuned pipe is very tight and must be tested in each individual case. No problems when using the stock muffler box. Losi DBXL Depending on the tuned pipe, mount starter with motor on top or on the l/h side. If the starter motor is to be mounted on the side, one screw of the motor roll cage must be replaced by a CSH screw. Carson C5 Only with Zenoah or CY engine, not with Smartech PT engine (different hole pattern on engine)! Carson C6 With the C6, depending on the body shell, trimming is required. HPI 5B/T Depending on the body shell, minor trimming is required. Carson Wild GP Attack Depending on the body shell, minor trimming is required. The accommodation of the engine killswitch, controller unit and wiring harness must be carried out at your own discretion. User Manual FG 4WD On-Road FG Monster FG 2WD On-Road horizontal engine FG 2WD/4WD Buggy current chassis Losi 5ive-T Losi DBXL FG 2WD Marder (old chassis)
Mecatech twin piston hydraulic brakeIt is the best brake for RC cars in the large model range from teh Mecatech FW01 and can be retrfitted to many FG models.Best quality for the highest demands!- The main brake cylinder is equipped with volume compensation and ensures constant braking pressure with good metering.- The brake calipers have a double-piston system and steel brake pads and teh epoxy brake discs ensure short braking distances. Installation instructions!Suitable for all FG off-road 2WD/4WD models (Leopard basis) and also for all FG off-road 2WD and 4WD models on a Marder basis with a laterally angled chassis such as (buggy / monster / stadium with original FG 700 ml tank) only with mounting base.Mounting base for all FG Offroad models:9438/01 a> Aluminum wheel chockWhen installing in an FG Evo 2020, 2020.1, 2020.2 and FG Raceline you need the adapter plates y1515.For FG Evo 12-14 models with the wishbone no. evo-2013-1-st-.html">1100/10 or 1100/11, the brake fits without additional accessories.For FG Evo 04-08 models with the wishbones no. evo-04-08-1st-.html">1100/05 or 1100/05, the brake must be 1100/05.When running wheel squares with Seeger ring, the ring has to be removed.Not for FG Formula 1 models.
The conversion kit contains all mechanical parts (no electric motor, esc and batteries) you need to convert a Carson Wild Attack or HPI Baja 5B to electric drive.Brushless motors from all common manufacturers with 56 - 58 mm diameter, about 100 - 115 mm motor can length, 700 - 850 KV and 8 mm output shaft will fit. We recommend the TT56112/700 Top Tuning Monster Brushless Motor 700 kV.For the esc,ZTW Beast 200A or other ESCs with similar dimensions and performance data are suitable.The battery box provides a total space of 180 x 84 x 50 mm for the batteries. Operation with 6S - 8S is recommended.The set contains: Battery and receiver box Complete aluminum motor mount Ball bearing for intermediate shaft Motor pinion Chassis struts and mounting plate for esc made of aluminum Extension cable for speed controller installation hardware Exploded view and assembly instructions
Product information "3000-38 Mecatech brake calliper complete, 1 piece" Original Mecatech spare part.
Mecatech Expert brake caliper complete with all connections, 1 piece. Suitable for FG steering knuckle (not Evo 2020 models),
Can be used on the right and left