8452 FG Rear disk brake - set

Genuine FG spare/option part. The rear disk brake is suitable for 1:5 models, Race-Trucks, the current version from Evo, 1:6 Off-Road and Monster models. The disk brakes prevent a breaking-out of the rear, have a very sensitive adjustment and are optically very effective. You can run the front disk brake with the gas servo, but make sure the servo has a minimun regulating power of six kilograms. We recommend to steer over two servos if you install front and rear disk brake. We deliver the disk brakes without uprights. In combination with the rim 6105/01 also suitable for Marder, Beetle and Pajero.Additional equipment for front and rear tuning disk brake:8472/01 Flexible bowden cables8474/05 Alloy bowden cable holder8469 Alloy guiding plate with ball bearing8479 Steel bush8448 Stud bolt for brake lining8458/02 Lasered tuning disk brake8457/03 Competition brake lining

Complete pre-assembled set front disc brakes for FG Marder, FG Off-Road Buggy and for Carson / Smartech Attack / Comanche / UNO / Monster Truck / CRT / CPT / Super Attack / Evo Attack / Spider / Big Attack , fits Conrad Big Pyro as well.For mounting in a Gas Blaster you must change you front shock mount and the front body shell holder, look at the pictures. Includes:- brake system with linkage- uprights- bearings- longer axle shafts- wider square drivesNo additional parts needed.

Genuine FG spare/option part. The rear disk brake is suitable for 1:5 models, Race-Trucks, the current version from Evo, 1:6 Off-Road and Monster models. The disk brakes prevent a breaking-out of the rear, have a very sensitive adjustment and are optically very effective. You can run the front disk brake with the gas servo, but make sure the servo has a minimun regulating power of six kilograms. We recommend to steer over two servos if you install front and rear disk brake. We deliver the disk brakes without uprights. In combination with the rim 6105/01 also suitable for Marder, Beetle and Pajero.Additional equipment for front and rear tuning disk brake:8472/01 Flexible bowden cables8474/05 Alloy bowden cable holder8469 Alloy guiding plate with ball bearing8479 Steel bush8448 Stud bolt for brake lining8458/02 Lasered tuning disk brake8457/03 Competition brake lining

Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all accessories (see also our pictures) required for installation.One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline Also suitable for electric models, but in conjunction with aluminum axle y0932 Bleeding instructionsDimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set

Genuine FG spare/option part. The FG Touring and Sports cars at scale 1:5 are known for their high quality and very detailed bodyshells true to original. Also the technically fully developed chassis are worth mentioning. These models are now available with a high-torque brushless engine. Surface conditions with maximum grip assumed speeds above 100 km/h can be reached and steered controlled. E stands for electric power which is equivalent to extremely high torque, high speed and all this without any engine noise. The Challenge Line models are equipped with a powerful 800 - 1300 kV brushless Motor and a 150A brushless ESC. This control can be regulated simply via transmitter or optionally via the program card.The models are built on a 4mm aluminium chassis with rear wheel drive and double wishbones front and rear. All borings are countersunk. Fully adjustable front and rear double wishbone suspensions.Further equipment points are: differential gear, oil-pressure shock absorbers with volume control and external, adjusting ring for the initial tension of the spring. All rotating parts on ball bearings.Tires are glued on the rims.For all versions of the electric cars, the LiPo batteries and the matching charger, as well as the radio system and the steering servo (RTR) are required. In our shop selection, the RTR set is available for a surcharge.For hassle-free assembly, FG recommends using LiPo batteries 2x 2S or 2x 3S, with a maximum dimensions of 150 mm in length and 50 mm in width. The model comes with the EC8 connector system equipped.

No matter where you will set this model into action - you will always be right in front with the FG Leopard 4E! No matter where you take it and where you use it - with the FG Leopard 4E you will be at the forefront! The E stands for electric power, the 4 for all-wheel drive. Extremely fast, a powerful torque and all without noise. The model is equipped with a powerful brushless motor and a controller. The Vehicle is supplied with white painted bodywork and decal sheet. The E stands for Elektro-Power and means extremely high torque, high top speed and all without engine noise. The Sportsline models are equipped with a powerful brushless motor and a brushless controller. Thanks to the built-in all-wheel drive, the models can be easily manoeuvred through any terrain without getting stuck. The controller can be easily adjusted via the transmitter or optionally via a programming card.You can select the car with complete RTR-equipment from the options menu. RTR equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. The control can be regulated simply via transmitter or optionally via a program card. For the final assembling you need LiPo batteries and the suitable charger. For an unproblematic mounting we recommend to use LiPo batteries with a max. length of 150mm and a width of 50mm. The model is delivered with the EC8 connector system.

Genuine FG spare/option part. The advantage of a one-way clutch over conventional or limited slip differentials is the combination of maximum propulsion and outstanding agility in the turns. This results in a 4WD vehicle with the quick turning-in of a 2WD while retaining the advantages of 4WD traction when accelerating out of corners.This applies to offroad and street cars alike.The inner races in the one-way clutch feature the internal spline drive to accept FG differential shafts. They are made of high strength steel, hardened and ground to very close tolerances. Combined with the large one-way clutches, this guarantees the transfer of the high maximum torque.Installation is pretty easy; the one-way clutch unit replaces the bevel gears in the diff including the satellite gear shaft and is inserted as a single piece into the differential case. You just have to take care that the side where the writing on the clutch can be seen goes to the left hand side (in the direction of travel).Fits FG-plastic differential case and HT- or FG-aluminum cases for non-self-locking differential versions.For vehicles not equipped with in-wheel brakes it should be noted that there will be no more braking action in front from the layshaft brake when running the one-way clutch as a front differentialOnly for 4WD models. Suitable for all differential housings except viscous and Powerlock diff.Contents:1 piece