y1129 Mecatech hydraulic brake Expert for FG, Carson and many more, incl. brake bleeding set
Product number:
y1129.0
EAN:
4058575023517
Product information "y1129 Mecatech hydraulic brake Expert for FG, Carson and many more, incl. brake bleeding set"
Genuine Mecatech spare/option part.
Full-metal hydraulic brake (like the former hydraulic FG brake).
Dimensions master brake cylinder:
Contents:
Full-metal hydraulic brake (like the former hydraulic FG brake).
- The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all, necessary for installation, accessories (see also our pictures)
- One version fits front and rear
- Fits onroad / offroad / monster and stadium cars from FG and others
- No need for alloy uprights!
- Fits Formular 1 models, Competition, Sportsline and E (in connection with alloy front uprights y0932
Dimensions master brake cylinder:
- Height: 75 mm
- Width: 48 mm
- Depth: 13 mm
Contents:
- 1 set
Login
Accessories / Spare parts
Top quality epoxy P-R-M Race brake discs with 10 dirt slots for removing dirt and abrasion, which will be transferred to the outside by the discs rotation. The epoxy P-R-M Race brake disc provides an optimal deceleration of the car without the unwanted fading (poor braking performance due to increased heat buildup)! The best braking action when using the epoxy P-R-M Race brake disc is achieved by the combination of the epoxy brake discs and steel brake pads (8456 or y19218). The epoxy P-R-M Race brake discs fit mechanical front and rear brakes on FG / Smartech / Carson cars with brake pads 8456 recommended for these applications.1 pair (2 pieces) Dimensions: Outer diameter: 60 mm Thickness: 2 mmsocket for 18 mm square wheel drive
Item N° y0132Linkage rod for MecaTech brakes, 2 pcs.Linkage rods for actuating of MecaTech master brake cylinders.Dimensions:Length: approx. 165 mmDiameter: approx. 2 mm
With this pedestal it is possible to install the master brake cylinder of the Mecatech brake in every FG 2WD offroad cars (buggy / monster / stadium). The pedestal is not necessary for Leopard cars.Please note: FG radio plate 6118/05 must be used, the fuel tank must be relocated (drilling required)!Fits Carson / Smartech 1/6 buggies and monster cars as well (2WD only!).Attention: this item fits chassis plates with late model bolt pattern (see picture) only!You can find the pedestal for the old bolt pattern .
Alloy pedestal to mount the master brake cylinder of the hydraulic brakes FG Magura 2, Mecatech Expert and Mecatech twin piston brake systems on the sloped chassis part of Off-Road Buggies and Monster models.Lieferumfang1x Pedestal for hydraulic brakes2x Countersunk screw with torx 4x12 2x Countersunk screw with torx 4x14
Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces
Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces
Dimensions: Diameter: 69 mm Material thickness: 1,6 mm
Offerset:2 Pairs MadMax Giant Grip tires2 Pairs MadMax rims2 Pairs MadMax inlays2 Pairs / 4 pieces adapter TT1020/01GIANT GRIP 190 x 70 with black colored MadMax Extreme rims, 20-fold screwed, very tough, with 24 mm hex drive and reinforced beadlock rings for Losi 5ive-T and Desert-Buggy XL as well as all HPI Baja 5 B/T cars.The GIANT GRIP provides giant traction through 96 about one cm² wide and 5 mm high strong lugs, getting ample grip even on loose surfaces like sand and soil.Due to the extreme strain caused by the GIANT GRIP tires the MadMax rim with reinforcement ring had to be optimized once more.The set consists of four tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01.The GIANT GRIP tires come with strong special tire inserts which allow to transfer the power without canting, even on heavy cars like the Losi 5ive-T.Dimensions:Outer diameter: 190 mmTire width at bead 70 mmTread width 80 mmReinforced 24 mm hex wheel driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces
Genuine FG spare/option part. Suitable for all mechanical disk brakes.Steel insert provides a strong thread for the mounting bolts.Contents:2 pieces
Customers also bought
FG Set price: 163,25 EURFits all FG 4WD cars (except FG Leopard/ TR-4!) Lost drive shafts are a thing of the past! Universal drive shafts allow for higher drive angles than dog bones or ball drives. This makes them a better choice for for wheel-side applications on front axles, where the angles of the steering and suspension meet.GPM universals for ball drive can be disassembled and therefore repaired or rebuilded if necessary. The center pin (No.: 66275/02)of the GPM universal joint is secured by a grub screw, which should be installed using a medium strength screw locking compound (y0114).Therefore the joint can be easily rebuilded by replacing the center pin for cheap and will be good as new again.The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM universal drive shaft set includes everything for the conversion of your FG 4WD.Set includes:Quantity:DescriptionPart number2 piecesUniversal drive shaftFG 662752 piecesDifferential ball drive cupGPM 6069/022 piecesDriveshaft booty10046 piecesSteel ballGPM 7080/022 piecesDrive shaft spacer springy1218
Genuine Mielke spare/option part.Mielke BIG-Tornado high performance tuned pipe system, especially for 1/5 FG 4WD touring cars and Race Truck with 535 mm wheelbase (not suitable for 510 mm wheelbase).Comes with manifold and installation hardware included.Content:1 set
Fits the y0190/46 HT-Alloy carrier with steel spur gear 46T for the layshaftInner diameter and bolt pattern are the same as a standard FG differential spur gear.Module: m=1,5Content:1 piece
Genuine HT spare/option part. Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.Contents:1 piece
Genuine HT spare/option part.Alloy a-arm rear upper for FG 2WD/4WD models. Replacement for FG item No.: 66225.Contents:1 piece
Similar products
%
Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all, necessary for installation, accessories (see also our pictures)One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline and E (in connection with alloy front uprights y0932Dimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set
Mecatech twin piston hydraulic brakeTwin piston hydraulic brakes with Epoxi rotors and steel brake pads for optimized braking performance. The master cylinders feature a volume compensation.Fits FG Evo 04 - 08, Mecatech FW01, Competition 07 - 08, Sportsline 08 and with pedestal in every FG offroad cars (buggy / monster / stadium with original FG 700 ml fuel tank).The brake fits without any further accessories on FG Evo-models which are equipped with the a-arms no. 1100/10 respectively 1100/11When running wheel squares with Seeger ring, the ring has to be removed.On FG Evo-models which are equipped with the a-arms no. 1100/05 respectively 1100/06, the brake has to be filled before the installation. In addition the ventilation nipple of the brake must be exchanged against the venting valve no. y0309Pedestal for installation for all FG Offroad-models: Mecatech twin piston hydraulic brake
Mecatech twin piston hydraulic brakeIt is the best brake for RC cars in the large model range from teh Mecatech FW01 and can be retrfitted to many FG models.Best quality for the highest demands!- The main brake cylinder is equipped with volume compensation and ensures constant braking pressure with good metering.- The brake calipers have a double-piston system and steel brake pads and teh epoxy brake discs ensure short braking distances. Installation instructions!Suitable for all FG off-road 2WD/4WD models (Leopard basis) and also for all FG off-road 2WD and 4WD models on a Marder basis with a laterally angled chassis such as (buggy / monster / stadium with original FG 700 ml tank) only with mounting base.Mounting base for all FG Offroad models:9438/01 a> Aluminum wheel chockWhen installing in an FG Evo 2020, 2020.1, 2020.2 and FG Raceline you need the adapter plates y1515.For FG Evo 12-14 models with the wishbone no. evo-2013-1-st-.html">1100/10 or 1100/11, the brake fits without additional accessories.For FG Evo 04-08 models with the wishbones no. evo-04-08-1st-.html">1100/05 or 1100/05, the brake must be 1100/05.When running wheel squares with Seeger ring, the ring has to be removed.Not for FG Formula 1 models.
Customers also viewed
The Sportsline quality at a reasonable price for beginners. For rookies and all those who simply just want to have fun and drive a DTM Audi, Mercedes or a fast Porsche. The Sportsline series is ideal for car modellers whose main focus is not just the chassis, but rather the combination of chassis and body shell.Technical description:The model has a 535 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, Evo gas tank, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads!Dimensions: Length: 880 mm Width: 392 mm Height: approx. 240 mm Wheelbase: 530 mm The car comes with an unpainted body shell!HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included. Value: 64,95 EUR Alloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EUR Ball bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURTouring cars in action!Painting tips:
%
Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all, necessary for installation, accessories (see also our pictures)One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline and E (in connection with alloy front uprights y0932Dimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set
Front disc brake hop-up for Marder Beetle off road and Beetle on road.