Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.
The new TT0900 electric starter is pre-assembled and fits a wide range of models including the Losi 5ive-T, 5ive Mini and DBXL, most FG models, HPI-Baja / Wild Attack series etc. The TT0900 electric starter can be started with the remote control (free channel required!). The new TT0900electric starter has much more power than the previous Electric starter thanks to the brushless motor and higher voltage. The popular Zenoah G320 is no longer a problem. It also no longer uses a one-way bearing, which clearly increases reliability. Also the installation space has been noticeably reduced by the motor and a planetary gearbox.The starter components to be fitted weigh about 666 grams plus the battery.For mounting the starter, the flywheel on the engine is replaced by the version with spring-loaded pawls included in the delivery. The tools required for this, piston stopper and flywheel puller, are also included in the delivery.For the 3rd channel the transmitter should have a switch with two positions (momentary switch preferred) or a controller. An additional channel is required for a remote engine killswitch. A killswitch is included in the scope of delivery, but a real fail-safe module such as TT0990 offers higher safety. A possibly already existing failsafe module can also be used.Due to the splitting of the functions engine start and engine stop on two channels, no more compatibility problems with different remote controls are to be expected, only the availability of free channels matters.A 3S LiPo battery is required as the power source.In the shops options menu, we offer a special battery with a more compact design (5,600 mAh/30C, 110 x 49 x 34 mm) which makes installation usually easier in many cars, as well as a battery with standard dimensions (3,900 mAh/60C, 135 x 45 x 25 mm). Of course, other 3S batteries can also be used at your own discretion, but the load capacity (capacity x C-rate) should be on a similar or higher level.Please note that we cannot ship batteries to countries outside the European Union!Since the starter unit can be mounted vertically or horizontally and the brushless starter motor is very small, almost all air filters and most tuned pipe systems can be used.Notes regarding necessary modifications known to us for mounting the starter depending on the vehicle: FG 4wd onroad Rear r/h plastic body mount, depending on position, slightly modified or relocated FG 2wd onroad horizontal engine No modifications Mecatech FW01 No modifications FG 4wd Buggy sportsline Depending on the body shell, minor trimming is required. FG 2wd Buggy current chassis Depending on the body shell, minor trimming is required. FG 2wd Marder (old chassis) Starter fits without modifications to the chassis plate. However, the body shell has to be cut out a bit more seriously in the area of the starter. A repositioning of the rear r/h body mount is recommended. FG Monster Cut the r/h side panel slightly and add a flat area to the aluminum tube which supports the panel on the engine Losi 5ive-B Depending on the tuned pipe, mount starter with motor on top or on the l/h side. Losi 5ive-B Mount the starter motor on the l/h side, space for the tuned pipe is very tight and must be tested in each individual case. No problems when using the stock muffler box. Losi DBXL Depending on the tuned pipe, mount starter with motor on top or on the l/h side. If the starter motor is to be mounted on the side, one screw of the motor roll cage must be replaced by a CSH screw. Carson C5 Only with Zenoah or CY engine, not with Smartech PT engine (different hole pattern on engine)! Carson C6 With the C6, depending on the body shell, trimming is required. HPI 5B/T Depending on the body shell, minor trimming is required. Carson Wild GP Attack Depending on the body shell, minor trimming is required. The accommodation of the engine killswitch, controller unit and wiring harness must be carried out at your own discretion. User Manual! FG 4WD On-Road FG Monster FG 2WD On-Road horizontal engine FG 2WD/4WD Buggy current chassis Losi 5ive-T Losi DBXL FG 2WD Marder (old chassis)
Genuine Mielke spare / option part.Starting by pull starter or by cordless screwdriver or electric starter is possible.Pull starter with hybrid starter function. Who does not know it? A torn starter rope, blisters on your finger from constant pulling or a defective starter pawl. All these problems are a thing of the past with the hybrid starter.With the help of a cordless screwdriver the engine can be started very easily and if the battery of the cordless screwdriver is empty, the engine can be started by using the conventional way with the pull-rope starter.Please note:The starter shaft for electric start is inserted in a straight line in extension of the crankshaft. No part of the vehicle must be in the way here. On a model with a longitudinally mounted engine (e.g. Losi 5ive or DBXL vehicles) the rear axle will usually prevent the use of the electric start. The normal pull start by cable remains possible.Contents:1 piece
Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.
3 mm high performance starter rope; with a breaking strength of almost a metric ton it is far superior to any other starter rope available. Even large displacement high compression engines are no match for this rope. Please note:The usual fusion of cutting edges and knots on standard starter ropes using a flame is mostly unrewarding with this rope! We therefore recommend securing the knots with 2 - 3 drops of superglue on the outside. Length approx. 80 cm; fits all current pull starters.
High quality flexible fuel line in your choice of blue, red, yellow, orange and green. Size:Length: approx. 1 meterOuter diameter: approx. 6.3 mmInner diameter: approx. 3.2 mmDiameters are 100% identical to the Zenoah Tygon hose #7352!
Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.
Wide neck flask with 50 ml.The "work of the devil!" The smell is normal! Among others this lubricant is suitable for the following model car applications:Drive shafts (if covered with boots)Transmission in enclosed housings (i.g. ring & pinion gears in Losi 5ive-T or Desert Buggy XL)Differentials which do not use friction padsChesterton® 787 Sliding Paste is a premium quality pure synthetic lubricant that will function effectively even at ultra high temperatures and pressures. Designed for the most severe operating conditions, it provides, through a novel chemical approach, lubrication at pressures up to 10687 kg/cm2 and 538°C.787 Sliding Paste is a unique thixotropic hybrid lubricant. Consisting of a semi-soft paste-like material, this product will flow to fill in small tolerances, yet will keep metal parts separated by the microscopic, symmetric, plates which slide over each other and provide effective lubrication long after the clean synthetic base oil has burned off. Applications for Chesterton 787 Sliding Paste can be found anywhere a need exists for a clinging semi-solid lubricant that will resist water washout and can withstand high temperatures and pressures. Unlike a grease which can turn to liquid and fail under extremely high loads and temperatures, 787 will maintain a slippery film on surfaces and prevent wear, galling and seizure at temperatures unthinkable for a grease. Use in such high temperature applications as lubrication of welding equipment, steel production facilities, smelting factories, forging furnaces, metal casting foundries, around exhaust stacks in power stations, turbine exhaust areas, and any other area exposed to extreme conditions. Because of its excellent resistance to water washout, the product works extremely well in outdoor applications such as on railroad switching equipment and wire rope cables.Composition:Chesterton 787 Sliding Paste is a unique hybrid material that suits the requirements of todays hotter running equipment. It consists of a combination of both organic and inorganic lubricating components and will perform effectively at temperatures ranging from -23°C to 538°C. The geometry of the solid constituents in 787 Sliding Paste is such that they slide over one another and remain undistorted even at the highest pressures parts and equipment are likely to see. The symmetry of the particles means they can withstand extra stresses compared to some inorganic materials which can shatter under extreme loads. The base oil used in Chesterton 787 Sliding Paste is a pure synthetic that will burn cleanly and leave no carbon or varnish to gum up parts and equipment. Because it contains no petroleum oils, it does not present the clean-up problems associated with waste petroleum residues.Features:Pure Non-Carbonizing, Synthetic Base n Lubricates at pressures to 10687 kg/cm n Withstands Temperatures to 538°CExcellent Water Washout Resistance n Non-Fling, Clinging LubricantLow Coefficient of FrictionNSF H2 - Registration number 133956 n No Toxic Heavy MetalsUltra-Fine ParticlesUnique 3 Phase Lubrication PackageApplications:Use in areas subject to extremes in temperature including smelting, forging, metal refining, glass manufacturing, plastics production, and in chemical, petrochemical and power plants, in foundries, around exhaust stacks, on rotary kilns in the cement and mining industry, etc. 787 is specifically designed to provide lubrication for surfaces subjected to extreme pressure. This would include wire ropes, cranes, railroad switch gear, and on large open gears on doors and bridges.Stem nuts, Lead screws, and Linear actuatorsFlange bolts and High tension studs n Press fit bushingsDirections:Brush or pump 787 Sliding Paste into areas needing to be lubricated. Product can be applied by squirt oiler. Spread evenly to thoroughly lubricate all parts and equipment which will see friction.Safety:Before using this product, please review the or appropriate safety data sheet for your area.
Regular price: 9,70 EUROffer price: 4,90 EURy0529/01 - Steel ball joint 4 mm r/h or l/h thread, 3 mm bore in ball, for servo saver/servo and other applications.Set contents:One each with M4 right hand thread or one each M4 with left hand threadPlease note:We recommend using a nut 54374 for locking the r/h thread ball joint to prevent the linkage from loss of adjustment. y0529 - Steel ball joint 6 mm r/h or l/h thread, 4 mm bore in ballSteel ball joints 6 mm r/h or l/h thread, 4 mm bore in ball, for steering rods and other applications.Set contents:One each with M6 right hand thread or one each M6 with left hand threadPlease note:We recommend locking the ball joints using M6 low height nuts y0888 or y0889 to prevent the linkage from loss of adjustment. y0529/02 - Steel ball joints M8 r/h or l/h thread, 5 mm bore in ball One pieces of steel ball joints with 5 mm bore in ball and M8 r/h or l/h thread.Suitable for most every 1/5 and 1/6 car!Replaces FG plastic ball joints # 6029/08 and # 6081/01 in conjunction with the conical spacers # 4429/02.Replaces Smartech # 32409 and # 32446 as well.Please note:We recommend using a nut 4472/02 or 4472/03 for locking the thread ball joint to prevent the linkage from loss of adjustment.
Regular price: 9,70 EUROffer price: 4,90 EURy0529/01 - Steel ball joint 4 mm r/h or l/h thread, 3 mm bore in ball, for servo saver/servo and other applications.Set contents:One each with M4 right hand thread or one each M4 with left hand threadPlease note:We recommend using a nut 54374 for locking the r/h thread ball joint to prevent the linkage from loss of adjustment. y0529 - Steel ball joint 6 mm r/h or l/h thread, 4 mm bore in ballSteel ball joints 6 mm r/h or l/h thread, 4 mm bore in ball, for steering rods and other applications.Set contents:One each with M6 right hand thread or one each M6 with left hand threadPlease note:We recommend locking the ball joints using M6 low height nuts y0888 or y0889 to prevent the linkage from loss of adjustment. y0529/02 - Steel ball joints M8 r/h or l/h thread, 5 mm bore in ball One pieces of steel ball joints with 5 mm bore in ball and M8 r/h or l/h thread.Suitable for most every 1/5 and 1/6 car!Replaces FG plastic ball joints # 6029/08 and # 6081/01 in conjunction with the conical spacers # 4429/02.Replaces Smartech # 32409 and # 32446 as well.Please note:We recommend using a nut 4472/02 or 4472/03 for locking the thread ball joint to prevent the linkage from loss of adjustment.
Regular price: 9,70 EUROffer price: 4,90 EURy0529/01 - Steel ball joint 4 mm r/h or l/h thread, 3 mm bore in ball, for servo saver/servo and other applications.Set contents:One each with M4 right hand thread or one each M4 with left hand threadPlease note:We recommend using a nut 54374 for locking the r/h thread ball joint to prevent the linkage from loss of adjustment. y0529 - Steel ball joint 6 mm r/h or l/h thread, 4 mm bore in ballSteel ball joints 6 mm r/h or l/h thread, 4 mm bore in ball, for steering rods and other applications.Set contents:One each with M6 right hand thread or one each M6 with left hand threadPlease note:We recommend locking the ball joints using M6 low height nuts y0888 or y0889 to prevent the linkage from loss of adjustment. y0529/02 - Steel ball joints M8 r/h or l/h thread, 5 mm bore in ball One pieces of steel ball joints with 5 mm bore in ball and M8 r/h or l/h thread.Suitable for most every 1/5 and 1/6 car!Replaces FG plastic ball joints # 6029/08 and # 6081/01 in conjunction with the conical spacers # 4429/02.Replaces Smartech # 32409 and # 32446 as well.Please note:We recommend using a nut 4472/02 or 4472/03 for locking the thread ball joint to prevent the linkage from loss of adjustment.
€4.90*
€9.90*(50.51% saved)
This website uses cookies to ensure the best experience possible. More information...