6293 FG Tuning pipe 1:6 - set
€148.10
Currently unavailable
Product information "6293 FG Tuning pipe 1:6 - set"
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Accessories / Spare parts
Genuine HT spare/option part. RC Tech Pipe Protect protects your exhaust against oil and rubber deposit while racing. A clean exhaust gives better resonance, which means better performance from your engine. Thanks to RC Tech Pipe Protect your exhaust system can evacuate the temperature better.Direction of useSpray a relatively thick layer of Pipe Protect from a close distance; +/- 15/20 cm on your new or just-cleaned and preferably polished exhaust pipe. After each ride clean the exhaust pipe with a clean cloth, if necessary slightly sprayed with some Pipe Protect. Treat the exhaust pipe again before each race.Contents:1 piece / 400 ml
Content: 400 Milliliter (€24.75 / 1000 Milliliter)
Genuine HT spare/option part.Spring band clamps are self-clamping and can self-adjust to diameter changes due to temperature variations or properties of the tube material.With this feature of self-adjustment, spring band clams are ideally suited for hose connections between exhaust manifold and tuned pipe with their high temperature load.Unlike worm drive clamps with their relatively large adjustment range, spring band clamps must be selected closely related to their intended application. For this purpose, the outer diameter of the hose in the mounted state must be measured. The clamp, whose nominal diameter corresponds most accurately to the value determined, should be used.In the options menu you can select from sizes ranging from 22 to 34 mm and packs of one or five clamps.Contents:1 piece / 5 pieces
Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.
Content: 50 Milliliter (€538.00 / 1000 Milliliter)
Customers also viewed
Different versions to choose:y0723 Gas-nitrited tuning clutch bell for FG, Smartech / Carson, Harm, RS5 & Co..Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.y0726 Gas-nitrited tuning clutch bell for Losi 5ive-T (unfortunately not available at the moment Alternatively original Losi clutch bell # LOSB5038) ) Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface and face which guarantees dimensional stability even under high loads! The shaft is a tiny bit longer than stock (about 0.2 mm) to prevent the bearings from binding.Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for genuine slot drive Losi pinions. Comes with bolts and spring washers included.y0726/01 Gas-nitrited tuning clutch bell for Losi DBXLGas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.y0729 Gas-nitrited tuning clutch bell for HPI Baja models, 1 pce.Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.
Genuine FG spare/option part. Contents:1 set
Reasonable tuning pipe for FG 1:6 Buggies and Monster models as well as for Carson 1:6 models.
Item N° 905046 Carson tuned pipe for Carson Gas Devil + CRT 4x4, Conrad Hell Devil, Smartech Titan - setLow mounting alloy pipe, installs between the wheels. Comes complete with manifold and mounting hardware.When installing this pipe on a Thunderbolt some minor modifications to the body shell are necessary to clear the manifold.
Complete 1/5 on-road tuned pipe system C5; with special connection hose (white Teflon), two pieces of hose clamps and spring-loaded universal attachment wire; including wire holder and extra strong manifolds with mounting screws. Set includes: multi-chamber tuned pipe spring-loaded attachment wire Teflon connecting hose hose clamps with fastening tab 18-32 mm installation hardware Tuned pipe dimensions: total length: approx. 310 mm li>maximum diameter: 50 mm inlet elbow angle: 180 ° tailpipe length: 22 mm tailpipe diameter: 16 mm
Genuine FG spare/option part. Standard tuning pipe for 4WD Sportsline Touringcar 1:5.Contents:1 piece
Genuine FG spare/option part. Contents:1 set