Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

TT0990/02 Top Tuning Futaba 2-pin male connector with cable for Failsafe

Product information "TT0990/02 Top Tuning Futaba 2-pin male connector with cable for Failsafe"

Genuine TT spare/option part.

Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.

2-pole connection cable with silicone insulation and 22 AWG/0.32 mm² cross-section, length approx. 80 mm.

Contents:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Similar products

Average rating of 0 out of 5 stars

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€42.90*

Average rating of 0 out of 5 stars

TT1000 Top Tuning Electronic 20 Amp Bigscale high voltage 30 Volt switch
tt_tt1000 Connector: TT1000/01 Universal in - Universal out
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece

€42.90*

Average rating of 0 out of 5 stars

TT1000/04 Spare screws for electronic switch TT1000
Genuine Top Tuning spare/option part. Set with four screws each M2,5x12 and M2,5x16.Contents:8 pieces

€2.90*

Average rating of 0 out of 5 stars

TT0990/04 Top Tuning Plug-in mount for 5 mm LED for Failsafe
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Plug-in mount for front panel installation, requires 8 mm diameter mounting hole.Contents:1 piece

€3.90*

Average rating of 0 out of 5 stars

TT0990/05 Top Tuning Jumper Set Failsafe
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Set with 2 each red and black jumpers for 2.5 mm contact spacing.Contents:4 piece

€3.90*

Average rating of 0 out of 5 stars

TT0990/03 Top Tuning JR/universal 3-pin female connector with cable for Failsafe
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.3-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 220 mm.Contents:1 piece

€3.90*

Average rating of 0 out of 5 stars

TT0990/01 Top Tuning Red illuminated 5 mm Led with cable for Failsafe
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Operating voltage 2.1 Volt, approx. 15 mA2-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 180 mm.Contents:1 piece

€3.90*

Customers also viewed

Average rating of 0 out of 5 stars

Original Zenoah repair-kits for 230/240/260/270/290/320 engines
7387 Rebuilt kit Zenoah G230Cylinder-piston repair kit for Zenoah engine G230. Set includes the following parts:Cylinder G230Piston G230Piston ring G230Cylinder foot gasketCentering disksPiston pin clipy0914 Original Zenoah G240 rebuild kitRebuild kit for the Zenoah G240 engine to replace piston/cylinder related parts. The kit includes the following parts:Cylinder G240Piston G240Piston ring G240Piston pin G240Piston pin retainer clipsCylinder gaskety0913 Original Zenoah G260 rebuild kit fits too CY, Losi and HPI enginesRebuild kit for the Zenoah G260 engine to replace piston/cylinder related parts, fits the G260 engines as well. The kit includes the following parts:Cylinder G260Piston G260Piston ring G260Piston pin retainer clipsCylinder gasketThis kit can also be installed on CY26, HPI and Losi engines, but you have to use Zenoah needle bearing 7312 and spacer washers 7312/01 for this application! y0915 Original Zenoah G270 rebuild kitRebuild kit for the Zenoah G270 engine to replace piston/cylinder related parts. The kit includes the following parts:Cylinder G270Piston G270Piston ring G270Piston pin G270Piston pin retainer clipsCylinder gaskety0916 Original Zenoah G290 rebuild kitRebuild kit for the Zenoah G290 engine to replace piston/cylinder related parts. The kit includes the following parts:Cylinder G290Piston G290Piston ring G290Piston pin G290Piston pin retainer clipsCylinder gaskety1016/095 Original Zenoah 32 cm³ 4 Bolt Rebuilt kitOriginal Zenoah 32 cm³ Rebuilt kit Top quality with Zenoah warranty!Set includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipThrust washer for needle bearingCover for transfer portAttention: For the assembling of the covers enclosed please use the HT-flange sealer y804 and pay attention to the assembling instructions enclosed.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 19015 Bindulin Siliconey0994 Marston sealery0807 MD-Sil RTV silicone sealer

€79.90*

Average rating of 0 out of 5 stars

Receiver switch, Multiplex connectors old, y0920 - 1pce.
Old version Multiplex type connectors for both battery and receiver.

€10.10*

Average rating of 0 out of 5 stars

P-CB10PX Futaba T10PX 2.4GHz with R404SBS receiver
The T10PXR is a 10-channel 2.4GHz computer radio control system with F-4G,T-FHSS SR / T-FHSS / S-FHSS and MiniZ modulation modes. The transmitter convinces with new design, new keypad and high quality carbon elements. New additions are some new buttons, 2- and 3-position switches and a rocker switch at the base of the transmitter.The Futaba T10PX comes with many new features that make the new RC-car radio flagship a very flexible transmitter.With 10 channels and many configuration options, the possible uses go far beyond those of a conventional car radio.From racer and drifter to crawler and boat to complex function models, everything is possible.Overview of the modulation types: F-4G, 10 channels / telemetry T-FHSS-SR, 4 channels T-FHSS, 4 channels / telemetry li> S-FHSS, 7 channels The new F-4G transmission protocol has been further improved compared to T-FHSS SR. Latency has been significantly reduced again and the range extended. At the same time, the receivers have become smaller.The optical center of the T10PX is the backlit 4.3 inch TFT color touch display with brilliant colors and high sharpness. Even in direct sunlight, all values on the display can be read excellently. The graphic user interface with the well-known easy to use Futaba menu structure, ensures easy operation. Navigation is intuitive via the screen and the additional buttons on the top of the transmitter.TELEMETRYSynchronized, bi-directional communication between transmitter and receiver with high telemetry data rate (up to 9 times per second), without loss of control channel response. Maximum of 31 telemetry sensors, alarm tone setting and output via beeper, vibration alert or voice output via internal speaker or optional headphones/active speaker. Telemetry data recording on SD card (SDHC) Telemetry data analysis via spreadsheet programs or LogView software Real-time display of telemetry data on integrated display Receiver signal strength indicator for monitoring the range Receiver undervoltage warning system for monitoring of the receiver battery Connection of up to 31 sensors to the S.BUS2 input S.BUS-TECHNOLOGY Connection option for S.BUS2 sensors All S.BUS servos can also be connected to normal servo outputs of the receiver Digital BUS technology for model sports Allows ideal placement of all components with efficient wire routing Future-proof, digital technology for all future Futaba components Features: Color LCD Touch Screen 4.3 Inch F4G System & Telemetry S-FHSS & T-FHSS Super Response (SR) Mode MiniZ S-FHSS 10 channels 40 models memory additional 3- and 2-step switches Brake mixer for large scale cars 4-wheel steering mixer Dual ESC mixer Mixer for track drives CPS LED mixer Gyro adjustment via T10PX microSD Slot (Data Log / Update) USB port Content of delivery Transmitter T10PX Receiver 404SBS Instruction manual DE/UK Accessories

€729.00*

Average rating of 0 out of 5 stars

SPMR5025 Spektrum DX5 Pro 5-Kanal DSMR
Original Spektrum Ersatz-/Tuningteil.Now ready to support the connectivity advantages of Smart Technology out of the box, the Spektrum DX5 Pro 2021 DSMR® also includes design and ergonomic improvements to give racers, bashers and boaters top-of-the-line features at an affordable price. Key Features Smart Technology compatible out of the box Five fully proportional channels Multiple mixing setups including Motor on Axle (MOA) Upgraded RF Module for stronger signal and improved output power 5.5-Millisecond frame rate with compatible receivers If you're a racer, basher or boater who's looking for an affordable radio with a "custom" feel and next-generation capabilities, look no further than the Spektrum lineup's new top-of-the-line surface transmitter: the 5-channel DX5 Pro 2021. Funktionen Smart Technology compatible out of the box Upgraded RF Module for stronger signal and improved output power Five fully proportional channels Generous ergonomic options for tailoring the transmitter to your feel Multiple mixing setups including Motor on Axle (MOA) DSMR® 2.4GHz technology (backwards compatible with DSM2®) 5.5-Millisecond frame rate with compatible receivers Advanced programming features, made easy to use with SimpleScroll interface Built-in telemetry Programmable vibe alerts 250-Model memory LiPo battery compatible (battery not included) Available as transmitter only or matched with an SR2100 DSMR® receiver, the DX5 Pro 2021 delivers the performance and comfort of a pro-class radio at a price that won't break your hobby budget. Its improved ergonomics, connectivity and programmability are ready to take your control to the next level. OUT-OF-THE-BOX SMART CONNECTIVITY The Spektrum DX5 Pro 2021 is ready right out-of-the-box to support the innovative connectivity of Spektrum Smart Technology. With a Spektrum Firma Smart ESC and Smart battery in your model, you'll have real-time telemetry data available at your fingertips to keep you aware of every component's status and to boost your confidence in its capabilities. Smart Technology ensures that all of your model's electronics work together seamlessly for the greatest efficiency and performance. It makes your entire system more responsive and simpler to use. IMPROVED SIGNAL QUALITY The DX5 Pro 2021 features Spektrum's latest RF module, engineered around DSMR® 2.4GHz technology. This generates a stronger and more robust signal, increases the telemetry range, and creates an extremely reliable connection between the transmitter and receiver. When paired with a receiver capable of 5.5ms frame rates, such as the SR2100, the DX5 Pro 2021 delivers lightning-fast response that gives new meaning to the word "connected". PRECISE STEERING WHEEL MECHANISM The ergonomically designed DX5 transmitter has a feel that any driver can appreciate. Its overall low weight minimizes fatigue, while the non-slip rubber grip and trigger-throttle action deliver precise control that feels perfectly natural. To these, the updated DX5 Pro 2021 transmitter adds a new steering wheel mechanism that increases the accuracy and precision of steering motion. UPDATED TRIM TABS Among the many ergonomic options available for tailoring the DX5 Pro 2021 transmitter to your personal touch are updated trim tabs, designed to make their operation easier while you drive your vehicle. ADVANCED PROGRAMMABILITY The DX5 Pro 2021 offers an impressive number of programming features and they're easy for anyone to use, thanks to the SimpleScroll programming interface that makes navigating menus and changing settings as simple as "scroll and click". You can program up to five drive modes per model to help dial in the perfect drag racing and lap times. Drive modes can also be used to program compatible AVC® (Active Vehicle Control) receivers to match your skill level, driving style, and terrain to provide predictable handling at every speed. There are multiple mixing setups, including Motor-On-Axle (MOA), plus ABS, Traction Control and 4-wheel steering, dual rates, expo and more. PROGRAMMING VIBE ALERTS You can select from a variety of vibe alerts for timer alarms, low battery voltage and other telemetry functions. Most of these can be set to go off when the voltage level or telemetry data exceeds specific values that you can easily define in the telemetry menus. Contents:1 piece

€369.99*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency