7316 FG Clutch blocks for Zenoah

€19.90*

Prices incl. VAT plus shipping costs

Available

Product number: fg_7316

EAN: 3410564516713

Product information "7316 FG Clutch blocks for Zenoah"

Genuine FG spare/option part.

Zenoah bolts 7318 are required for installation.

Content:

2 pieces

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Alternatives

y1419 Sintered steel clutch for Zenoah and many other engines from 23 cm³ to 32 cm³

Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!

€19.00*

5316 FG Clutch blocks for Chung Yang

Spare part for Chung Yang.Fits too Zenoah ZG22, G230/240/260/270/290/320.Zenoah bolts 5318 are required for installation.Content:Two clutch blocks

€23.00*

Details

y0733 Big Scale-EXTREME, adjustable 3 - shoe clutch

With the Big Scale-EXTREME an adjustable clutch for very special requirements has been designed:For large-displacement enginesFor heavy or high traction cars (Losi, HPI)For modified performance enginesFor the demanding off-road useRapid wear of a clutch is a sign of constant slipping, even beyond engagement speed. In this case, the clutch does not transfer the applied torque.This is where the Big ScaleEXTREME sets a new standard.The new design of the "Extreme" prevents the centrifugal forces of clutch springs or lever side of the clutch shoes from counteracting the centrifugal force of the friction pad side even after engagement.As a result this clutch can transfer lots of power with minimal wear.The new design ensures that the centrifugal forces are transferred in full to the clutch lining. Precise engagement and disengagement even under high loads and inside of closed clutch bell carriers means no problem for this clutch.The clutch can be easily adjusted to the engagement speed through three set screws without clutch bell removal, so you can match the characteristics of your engine.The special clutch lining of the Big Scale-EXTREME is particularly wear-resistant and - especially in combination with a high-quality nitrited clutch bell (), guarantees for an exceptionally long service life! Contrary to the "Cross" or "Race" version there's no need to uninstall the clutch from the engine for maintenance. All parts are easily accessible from the front after removing the front plate.Please see the specifications tab for further information and handling advices!The regular price of the Big Scale-EXTREME is EUR 139.90

€149.90*

Details

Mielke 5543 Power Gearshift clutch for FG (except Formula 1+Evo2020), Harm and RS5, carbon, 2,4mm springs with long clutch carrier

The new adjustable system features three carbon pads with special 2.4 mm springs.Weight of the complete clutch is 70 grams. Very wear resistent when running with the recommended clutch bells.Adjustable friction points: First gear - 8.500 U/min. Second gear - 9.300 U/min. Third gear - 10.100 U/min. Fourth gear - 11.000 U/min.With tool #5445 the engagement speed can be adjusted to different settings within a range from about 8,500 to 11,000 rpm.

€129.50*

Accessories / Spare parts

y1419 Sintered steel clutch for Zenoah and many other engines from 23 cm³ to 32 cm³

€19.00*

7318 FG Dowel screw set for clutch blocks Zenoah

Genuine FG spare/option part. Part is delivered in silver or black color from vendor!Content:2 pieces

€9.90*

y0733 Big Scale-EXTREME, adjustable 3 - shoe clutch

€149.90*

Details

7316/01 FG Tuning-clutch block for Zenoah

Genuine FG spare/option part. Spare part for Zenoah ZG22, G230RC, G230RC 04 and G260RC.Zenoah bolts 7318 are required for installation.Contents:2 pieces

€37.90*

Customers also bought

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€37.90*

7317/11 FG Clutch spring reinforced 2,7mm G230/260/240/270/290/320

Genuine FG spare/option part. Fits Zenoah G230/260/240/270/290/320.Reinforced clutch spring for the Zenoah standard clutch. Engagement speed approx. 8000rpm. The engine has a higher torque and therefore more power for acceleration according to the raised operative speed. Suitable for all Zenoah engines.Contents:1 piece

€8.90*

7474 FG Alloy gear plate 97 for 2WD and 4WD

Genuine FG spare/option part. Suitable for all FG 1:5 and 1:6 2WD and 4WD models. Best fitting of ball bearing seat and distance of gear shaft, non-twisting. To mount this gear plate into the models Marder, Beetle, Beetle On-Road, Pajero and Monster the rear brake 7040/01 is needed.Bearing seatsClutch bell: 22 x 6 mmLayshaft: 19 x 7 mmContent:1 piece

€99.90*

y7343/08 Champion Spark plug for Zenoah/CY and other

Genuine Champion spare/option part.The Champion spark plug means higher speed range, longer time of exposure andimproved starting function. Thread size M10 x 1 fits CY / Fuelie / PT / Zenoah G230/240/260/270/290 and otherSerienkerze vom Zenoah G230/240/260/270.The most widely used, qualitatively best spark plug for the model sport! Especially by the most 1/6 scale models the short ceramic body is indispensable, because otherwise on grounds of the heightened mounting position- the spark plug would protrude beyond the roll cage and therefore is extremely fragile by flashovers.Contents:1 piece

€9.90*

15478 HPI Pull starter 1/5

Genuine HPI spare/option part. Content:1 piece

€59.90*

FG TR4 Truggy 4WD HT-Edition

Ready for an extra portion driving fun? Then try the TR4 made by FG! Agressive appearance combined with the Leopard 4 chassis results in an optimal handling and stunning top speed with lots of driving fun wich will thrill you. Equipped with a 26 cm³ two-stroke gasoline engine with installed pull-start system. The TR4 is an uncomplicated complete package with well-tired racing technology.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical information:Strong 26 cm³ gasoline engineMaintenance friendly chassisTwo differential gearsHardened driving partsCompletely ball-bearedLarge-volume aluminium dampersAggressive rim designGrip tires with 185 mm diameter and 95 mm widthReady to use Off-Road filterSimple handlingLow weightPure driving funHT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURDimensions: Length: 760 mm Width: 520 mm Height: 320 mm Wheelbase: 534 mm

€1,279.95*

Configure now