y1244, Battle Gear nerf bars for Carson Wild GP Attack and HPI Baja 5B, set
Product information "y1244, Battle Gear nerf bars for Carson Wild GP Attack and HPI Baja 5B, set"
These welded steel bars are bolt-on without drilling required, and protect your buggy's side and rear tires from damage. Some minor modifications to the body shell are recommended to clear the bars, but are not absolutely necessary.
All mounting bolts included.
All mounting bolts included.
Login
Similar products
Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.
GPM air filter cover which fits easily over your existing air filter. A rubber band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments. Fits all common filters, foam or fabric (K&N) style.
at_at001 Color:
AT-001/02 - Red
Genuine Atop spare/option part. Colored fuel hose with clams and suction tubesArea Rc High flow fuel line kit.This high flow fuel line kit fits the HPI Baja series and the Losi 5ive-T/B and Mini. It may fit other large scale cars as well.The kit comes with 6 pieces of fuel line clips and 2 assembled plastic fittings. Those fittings cannot be compressed by the tanks fuel line grommet, so the inner diameter remains constant which improves fuel delivery to the carb.Fuel line dimensions:Length: 1mInside diameter: 3 mmOuter diameter: 6 mmAvailable colors: AT001/01 - YellowAT001/02 - RedAT001/03 - BlueAT001/05 - GreenIncludes:2 x Assembled plastic fittings6 x Fuel line clipsTygon fuel line
%
tt_tt1000 Connector:
TT1000/01 Universal in - Universal out
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
The new TT0900 electric starter is pre-assembled and fits a wide range of models including the Losi 5ive-T, 5ive Mini and DBXL, most FG models, HPI-Baja / Wild Attack series etc. The TT0900 electric starter can be started with the remote control (free channel required!). The new TT0900electric starter has much more power than the previous Electric starter thanks to the brushless motor and higher voltage. The popular Zenoah G320 is no longer a problem. It also no longer uses a one-way bearing, which clearly increases reliability. Also the installation space has been noticeably reduced by the motor and a planetary gearbox.The starter components to be fitted weigh about 666 grams plus the battery.For mounting the starter, the flywheel on the engine is replaced by the version with spring-loaded pawls included in the delivery. The tools required for this, piston stopper and flywheel puller, are also included in the delivery.For the 3rd channel the transmitter should have a switch with two positions (momentary switch preferred) or a controller. An additional channel is required for a remote engine killswitch. A killswitch is included in the scope of delivery, but a real fail-safe module such as TT0990 offers higher safety. A possibly already existing failsafe module can also be used.Due to the splitting of the functions engine start and engine stop on two channels, no more compatibility problems with different remote controls are to be expected, only the availability of free channels matters.A 3S LiPo battery is required as the power source.In the shops options menu, we offer a special battery with a more compact design (5,600 mAh/30C, 110 x 49 x 34 mm) which makes installation usually easier in many cars, as well as a battery with standard dimensions (3,900 mAh/60C, 135 x 45 x 25 mm). Of course, other 3S batteries can also be used at your own discretion, but the load capacity (capacity x C-rate) should be on a similar or higher level.Please note that we cannot ship batteries to countries outside the European Union!Since the starter unit can be mounted vertically or horizontally and the brushless starter motor is very small, almost all air filters and most tuned pipe systems can be used.Notes regarding necessary modifications known to us for mounting the starter depending on the vehicle: FG 4wd onroad Rear r/h plastic body mount, depending on position, slightly modified or relocated FG 2wd onroad horizontal engine No modifications Mecatech FW01 No modifications FG 4wd Buggy sportsline Depending on the body shell, minor trimming is required. FG 2wd Buggy current chassis Depending on the body shell, minor trimming is required. FG 2wd Marder (old chassis) Starter fits without modifications to the chassis plate. However, the body shell has to be cut out a bit more seriously in the area of the starter. A repositioning of the rear r/h body mount is recommended. FG Monster Cut the r/h side panel slightly and add a flat area to the aluminum tube which supports the panel on the engine Losi 5ive-B Depending on the tuned pipe, mount starter with motor on top or on the l/h side. Losi 5ive-B Mount the starter motor on the l/h side, space for the tuned pipe is very tight and must be tested in each individual case. No problems when using the stock muffler box. Losi DBXL Depending on the tuned pipe, mount starter with motor on top or on the l/h side. If the starter motor is to be mounted on the side, one screw of the motor roll cage must be replaced by a CSH screw. Carson C5 Only with Zenoah or CY engine, not with Smartech PT engine (different hole pattern on engine)! Carson C6 With the C6, depending on the body shell, trimming is required. HPI 5B/T Depending on the body shell, minor trimming is required. Carson Wild GP Attack Depending on the body shell, minor trimming is required. The accommodation of the engine killswitch, controller unit and wiring harness must be carried out at your own discretion. User Manual FG 4WD On-Road FG Monster FG 2WD On-Road horizontal engine FG 2WD/4WD Buggy current chassis Losi 5ive-T Losi DBXL FG 2WD Marder (old chassis)
The conversion kit contains all mechanical parts (no electric motor, esc and batteries) you need to convert a Carson Wild Attack or HPI Baja 5B to electric drive.Brushless motors from all common manufacturers with 56 - 58 mm diameter, about 100 - 115 mm motor can length, 700 - 850 KV and 8 mm output shaft will fit. We recommend the TT56112/700 Top Tuning Monster Brushless Motor 700 kV.For the esc,ZTW Beast 200A or other ESCs with similar dimensions and performance data are suitable.The battery box provides a total space of 180 x 84 x 50 mm for the batteries. Operation with 6S - 8S is recommended.The set contains: Battery and receiver box Complete aluminum motor mount Ball bearing for intermediate shaft Motor pinion Chassis struts and mounting plate for esc made of aluminum Extension cable for speed controller installation hardware Exploded view and assembly instructions
y86479 Color:
y86479/01 - Black
Highly flexible driveshaft boots, equivalent to HPI part # H86479.Available in the following colors:y86479/01 - blacky86479/02 - redy86479/03 - orangeContents:4 pieces
Complete set of screws, nuts and washers for HPI Baja 1/5 vehicles.The set includes a total of 434 screws, nuts and washers in different quantities which are all used on HPI Baja 1/5 vehicles and Carson 1:5 Wild GP Attack.11 sizes of cap head screws9 sizes of CSH screws10 sizes of button head screws4 sizes of set screws2 sizes of washers3 sizes of lock washers3 sizes of self-locking nuts2 sizes of nuts with serrated flange2 sizes of flanged self tapping screwsComes in a high quality 190x170x40 mm assortment box.Contents:Cap head screws in 12.9:20 piecesM3x126 piecesM3x4510 piecesM4x612 piecesM4x1212 piecesM4x2510 piecesM4x306 piecesM4x507 piecesM5x206 piecesM5x306 piecesM5x356 piecesM6x25CSH screws in 10.9:10 piecesM3x2010 piecesM4x1019 piecesM5x1616 piecesM5x206 piecesM5x302 piecesM5x407 piecesM6x14Button head screws in 10.94 piecesM3x1610 piecesM3x303 piecesM4x166 piecesM5x123 piecesM5x302 piecesM5x356 piecesM5x406 piecesM5x452 piecesM6x306 piecesM6x30Grub screws:6 piecesM3x39 piecesM4x46 piecesM4x124 piecesM6x45Washers in Din125:10 pieces3,2x6,8x0,512 pieces4,3x8,7x0,8Safety washers:20 piecesM420 piecesM520 piecesM6Self-locking nuts:10 piecesM310 piecesM415 piecesM5Flanged nuts with serrated base:21 piecesM410 piecesM5CSH screws Torx:10 piecesM4x15 (4,2x16)10 piecesM4x18 (4,2x19)Schneidschrauben Torx mit flanged:10 piecesM2,6x1012 piecesM3x10
Reinforced spring for Zenoah OEM clutch with 2.7 mm wire diameter and five coils. Engagement speed is around 7500 rpm, which allows the engine to build up more power and torque for accelleration.Fits Zenoah, CY and most other engines in the 23 - 30 cc range with stock clutch.
y1244 Color:
y1244-4 orange
These welded steel bars are bolt-on without drilling required, and protect your buggy's side and rear tires from damage. Some minor modifications to the body shell are recommended to clear the bars, but are not absolutely necessary.All mounting bolts included.
y0722 Quanity:
y0722/01 - Set of 4
For sealing the axles on Losi 5ive-T and Mini cars, keeps debris out of the inner screws which secure the retainer pin. Set of 4 or set of 10 to choice.Can be used for Losi 5ive-T, Mini and HPI Baja cars.
Item N° y1183/02FG rim to HPI model, drive rim adapter, separate for the front, 2 pcs.These adapters are machined from gas nitrited steel and enable you to put standard rims with 18 mm square drive (FG, Carson, Lauterbacher a.s.o.) on the HPI Baja 5B/SS/T. The track width will be substantially increased.For a complete set covering front and rear axle you need part number y1183.This set includes rim adapters with installation hardware for the front axle only.Measures for front:Outer diameter: circa 17,59 mLength: circa 55,10 mm
Customers also viewed
Normal price: 249,90 EUR Tuning front disk brake system for the HPI Baja 5B/SS/5T/5sc, the conversion kit includes all necessary parts. The brake includes the finest parts available for a cable brake and has the following features: * uses existing mounting points for all parts * brake pads and 70 mm diameter stainless rotors made by RS-5, the best performing combination available * hardened stud bolts for the brake pads * billet brake levers, no tweak and best transfer of servo power * ultraflex bowden cables * brake cams run in hardened steel bushings and brass guide plates (miniature bearings don't last in offroad cars) * billet alloy bowden cable support block with adjustment screws * billet alloy bowden cable mounts at the calipers * pre-assembledOn a 5T the stud bolts which hold the brake pads will interfere with the ribs in the rim. However, modifying the rim or swapping the stud bolts for long csh screws allows for installation on a 5T.Spare parts for this brake as a PDF-file with spare part numbersWe highly recommend the installation of a stronger throttle servo to take full advantage of this brake system. The is an excellent choice.
Genuine GPM spare/option part. High quality cnc machined parts made by GPM Racing Products from high strength billet aluminum. Fits all vehicles from the HPI Baja 5 line and Carson Wild GP Attach.Contents:1 piece