y1183/02 FG rim to HPI model, drive rim adapter, separate for the front, 2 pcs.
€19.90
% €24.90 (20.08% saved)
Available
Product information "y1183/02 FG rim to HPI model, drive rim adapter, separate for the front, 2 pcs."
FG rim to HPI model, drive rim adapter, separate for the front, 2 pcs.
These adapters are machined from gas nitrited steel and enable you to put standard rims with 18 mm square drive (FG, Carson, Lauterbacher a.s.o.) on the HPI Baja 5B/SS/T. The track width will be substantially increased.
For a complete set covering front and rear axle you need part number y1183.
This set includes rim adapters with installation hardware for the front axle only.
Measures for front:
- Outer diameter: circa 17,59 m
- Length: circa 55,10 mm
Login
Accessories / Spare parts
Grooved pin 4x19 mm, replacement pins for HPI adaptor to install FG rims on HPI Baja cars.Diameter: 4 mmLenght: 19 mmDelivery contents: 5 pieces
Hardware set for wheel adapter FG rim to HPI car:y1183y1183/02y1183/03
Alternatives
Genuine HT spare/option part.This adaptor allows you to install all MadMax/HPI tire/rim combinations on FG, Carso, Smartech 2WD/4WD and other cars with the same wheel shaft configuration. Losi 5ive tires can be used as well, but they hey have to be mounted on MadMax/HPI rims because Losi rims are too thick at the center. The adapter is drilled for 8 mm wheel shafts (FG, Smartech/Carson and many more!), hex size of wheel drive and wheel nut is 24 mm hex with M18x1.0 thread (same as HPI).Please note:FG wheel shafts come with either M6 or M8 thread size. It can even happen that a vehicle has different thread sizes front and rear! Therefore, please make sure which version is required before placing an order.Converting your car takes only a couple of minutes with this easy to install adaptor. just see picture "installation instruction" for a schematic installation.Contents:2 pieces
Customers also bought
Genuine HT spare/option part. For all Zenoah G230/240/260/270/290/320 / CY / Fuelie / PTTemperature and dimensionally stable. Thickness: 1,0 mm.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece
These protective covers prevent the shock piston rods and seals for wear caused by dirt. They fit most 1/6 and 1/5 scale shocks.Not suitable for Gas Devil, Thunderbolt, Helldevil, CRT 4x4!- total length 150 mm for all FG / Carson / Smartech / Conrad and all dampers with a diameter from 22 to 30 mm. Set of 4
Item N° y0656 Shocks for Bigscale cars 1/6 and 1/5, 173 mm long, 2 pcs.GD type extra high capacity shock for largescale cars. Shock comes complete with spring and is factory filled.Dimensions:Mounting hole distance (extended): 173 mmTotal length (extended): 190 mmTravel: 56 mmShock shaft diameter: 6 mmBody diameter: 30 mm
Stainless steel stabilizer mount for FG EVO a-arms (except 2020 series!), complete with installation hardware. M5 thread, for 4 mm stabilizer bar.Contents:2 pieces
Customers also viewed
Genuine HT spare/option part.This adaptor allows you to install all MadMax/HPI tire/rim combinations on FG, Carso, Smartech 2WD/4WD and other cars with the same wheel shaft configuration. Losi 5ive tires can be used as well, but they hey have to be mounted on MadMax/HPI rims because Losi rims are too thick at the center. The adapter is drilled for 8 mm wheel shafts (FG, Smartech/Carson and many more!), hex size of wheel drive and wheel nut is 24 mm hex with M18x1.0 thread (same as HPI).Please note:FG wheel shafts come with either M6 or M8 thread size. It can even happen that a vehicle has different thread sizes front and rear! Therefore, please make sure which version is required before placing an order.Converting your car takes only a couple of minutes with this easy to install adaptor. just see picture "installation instruction" for a schematic installation.Contents:2 pieces
Hardware set for wheel adapter FG rim to HPI car:y1183y1183/02y1183/03
Rim with 18 mm square drive. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.1/6 monster truck tires, hard, glued on chromed FG Monstervrim. Outer Ø 210mm, width 120mm, fits FG Marder, Off-Road Buggy, Beetle and Monster cars. Fits other makes of 1/6 cars as well, wheel square size must be checked prior to installation. Installation of tires with a different diameter may require a change in gear ratio as well.Diameter 195 mm Width 120 mm 1 pair
Complete steering rods and tie rod between steering servo and servo saver with steel turnbuckles. Dimensions: Hole to hole: 120mm Total length: 135mm