y0730/01 Clutch shoes with pads

€47.90*

Available

Product number: y0730_01

EAN: 4058575036227

Product information "y0730/01 Clutch shoes with pads"

Genuine GPM spare/option part.

Part no. 01 for GPM Big-Scale clutch. Installation ready set of 3 with glued-on organic pads.

Replacing the clutch linings

For replacing the friction pads please proceed as follows:

1. Remove clutch from engine
2. Disassemble clutch
3. Remove the screws fixing the friction pads
4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal
5. Thoroughly degrease the bonding area of clutch shoes and new pads
6. You must use the special adhesive y0743 Clutch-Safe!
7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces
8. Insert the lining into the clutch shoe and align
9. Fix the pad in place with screw y0730/03, just hand-tighten it
10. Remove excessive glue with a rag
11. Preheat oven to 120 °C.
12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down
13. Reassemble clutch and install it onto the engine
14. Wait at least one hour after the gluing process before using the clutch

y0730	y0731

Content:

3 x aluminum clutch shoes with
3 x press-fitted dowel pins (part no. /15) with
3 x glued-on organic clutch pads (part no. /02) with
3 x M3x5 mm safety screws (part no. /03) installed

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Accessories / Spare parts

y0743 Clutch-Safe 10 g, adhesive especially for clutch pads

Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube

Content: 10 Gramm (€495.00* / 1000 Gramm)

€4.95*

y0730/02 Special wear resistant organic replacement pad

Genuine GPM spare/option part. Use a high strength two-component adhesive (e.g. Clutch-Safe) to glue in the pads and lock them with the countersunk screws M3x5 (part no. y0730/03)Part no. 02 for GPM Big-Scale clutch.For replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731Content:3 pieces

€19.90*

y0730/03 Screws for clutch pads M3 x 6 mm

Genuine GPM spare/option part. Part no. 03 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€2.90*

y0730/04 Spring pressure plates, outer side (with positioning pin)

Genuine GPM spare/option part. Part no. 04 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€8.90*

y0730/05 Replacement spring silver 1.3 mm, off-road stock

Genuine GPM spare/option part. Equipped with the silver 1.3 mm springs the Big-Scale clutch provides relatively low slippage and easily controllable clutch engagement at medium rpms.Part no. 05 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€8.90*

y0730/06 Replacement spring gold 1.4 mm

Genuine GPM spare/option part. Equipped with the gold 1.4 mm springs the Big-Scale clutch provides medium slippage and noticeable clutch engagement at medium to higher rpms. On-road clutch standards.Part no. 06 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€8.90*

y0730/08 Spring pressure plates, inner side (w/o positioning pin)

Genuine GPM spare/option part. Spring pressure plates, inner side (w/o positioning pin). Part no. 08 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€6.90*

y0730/09 Adjustment cam Big-Scale clutch

Genuine GPM spare/option part. Part no. 09 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€18.90*

y0730/10 Adjustment screw M5 x 8 mm

Genuine GPM spare/option part. Part no. 10 for GPM Big-Scale clutch.y0730y0731Content:2 pieces

€1.90*

y0730/12 CSH screws M3 x 8 mm

Genuine GPM spare/option part. y0730y0731Part no. 12 for GPM Big-Scale clutch. M3 x 8 mm for clutch housing.Content:3 pieces

€1.90*

y0730/13 Bushings for clutch shoe pins

Genuine GPM spare/option part. Part no. 13 for GPM Big-Scale clutch.Dimension:Inside diameter: 3 mmOutside diameter: 4,5 mmFlange: 7,2 mmy0730y0731Content:6 pieces

€4.90*

y0730/14 Clutch housing main section

Genuine GPM spare/option part. Part no. 14 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€19.90*

y0730/17 Clutch housing

Genuine GPM spare/option part. Part no. 17 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€22.90*

Customers also viewed

y0731 GPM Big Scale-Race adjustable 3 block clutch

Genuine GPM spare/option part. The Big Scale-Race clutch is equipped with 1.4 mm springs, is especially suitable for On-road use (not for Formular 1).Adjustable 3-shoe clutch for:ZenoahChung YangHPI - FueliSmartech PTAnd many other enginesThe GPM-Big Scale clutch:Suitable for racing and for the ambitious hobbyist driver. Unlike the stock clutch, the installed GPM-Big Scale clutch can be adjusted by turning one single screw. A 2.5 mm allen key wrench is required for this application.Therefore it is possible to precisely adjust the clutch engagement depending on track characteristics.Attention: You must use adhesive y0743 Clutch-Safe when replacing clutch pads!y0730y0731Content:1 piece

€99.90* €129.90* (23.09% saved)

y0739 GPM Big Scale-ALLOY adjustable 3 block clutch for 1/5 scale On-Road models

regular Price GPM Big Scale - ALLOY 119,90 EUR===================================The Big Scale-ALLOY clutch is equipped with 1.4 mm springs.This version is particularly suitable for on-road use.Adjustable 3-shoe clutch for:Zenoah / Chung Yang / HPI - Fuelie / Smartech PT and many other engines.The GPM-Big Scale clutch:Suitable for racing and for the ambitious hobbyist driver. Unlike the stock clutch, the installed GPM-Big Scale clutch can be adjusted by turning one single screw. A 2.5 mm allen key wrench is required for this application.Therefore it is possible to precisely adjust the clutch engagement depending on track characteristics.Slight aluminum deposits in the clutch bell and corresponding wear marks in the clutch shoes are normal with the Big Scale ALLOY clutch and have no negative effect on the function. Caution: It is very important that when swapping the full-aluminum clutch shoes against the organic friction pads of a Big Scale CROSS or RACE to use a different or new , because the rough surface of the aluminum deposits in the clutch bell left by the Big Scale ALLOY will cause a high wear on the organic pads.

€119.90* €149.90* (20.01% saved)

y0730/05 Replacement spring silver 1.3 mm, off-road stock

€8.90*

FG Formula 1 Sportsline

Completely mounted, with a 26 cm³ combustion engine and final speed of almost 100 km per hour, what else would you want?A further additional improvement is the installed front disk brake. A clear polycarbonate bodyshell is included.Quality and high-class equipment to a sensible price.Technical description of the Formula 1 Sportsline chassis:The undercarriage of the FG Formula 1 is built on a high-strength 5 mm alloy chassis. All chassis borings (screws) are countersunk. The front and rear axle with their various adjusting possibilities as king pin angle, trailing effect etc. consist of double delta wishbones. The double delta wishbones of the rear axle are supported by additional track rods which enable you a very fast set-up. All adjustments can be made without a dismounting of parts according to the fixed wishbone threaded rods with right-/left-handed thread.The model is equipped with 4 alloy oil-pressure shock absorbers. The push-rod suspension ensures the transmission between single wheel suspension and shock absorber.We deliver this chassis with a powerful 26 cc combustion engine. The engine's power is transmitted over a four-block Teflon clutch on a synchronous belt drive. This synchronous belt drive is also designed for a higher driving power. The BBS wheels and the tires are copies of the big models. All rotating parts are supported by ball bearings.The construction of the Formula 1 chassis is not identical with the other 1:5 scale FG models such as Merc. C-Class, Race Truck a.s.o. and therefore it can?t be converted into or from these models by a conversion kit.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 960 mmWidth: 440 mmHeight: 230 mmWheelbase: 620 mmFormular 1 models in action!

€1,279.00* €1,416.50* (9.71% saved)

Configure now

y0743 Clutch-Safe 10 g, adhesive especially for clutch pads

Content: 10 Gramm (€495.00* / 1000 Gramm)

€4.95*

y0733/01 Clutch shoes with bonded organic friction pads

Clutch shoes with bonded organic friction pads for BigScale Extreme clutch.

€54.90*

8501/05 FG Alloy differential self-locking fourfold

Genuine FG spare/option part.In order to be able to transfer even more power and torque on to the rear wheels we distributed the valve effect over 4 friction disks by this quadruple self-locking differential gear.Suitable for all 1:5 models, Trucks, Formula 1 and Leopard.Please note: The differential comes unassembled, we recommend assembly tool: 8505 FG for bevel gear installation.Contents:1 set

€219.95*