y0730/19 Full-aluminum clutch shoes conversion kit

€54.90*

Available

Product number: y0730_19

EAN: 4058575047445

Product information "y0730/19 Full-aluminum clutch shoes conversion kit"

Genuine GPM spare/option part.

Full aluminum clutch shoes are very successfully used in 1/5 onroad racing applications.

Therefore we can now offer the GPM conversion kit for BigScale Cross/Race clutches to full-aluminum clutch shoes. Made of a special alloy to suit this application the kit comes with 1.4 mm wire diameter springs and new spring pressure plates.

Slight aluminum deposits in the clutch bell and corresponding wear marks in the clutch shoes are normal with the Big Scale ALLOY clutch and have no negative effect on the function.

Caution:

It is very important that when swapping the full-aluminum clutch shoes against the organic friction pads of a Big Scale CROSS or RACE to use a different or new , because the rough surface of the aluminum deposits in the clutch bell left by the Big Scale ALLOY will cause a high wear on the organic pads.

y0730	y0731

Content:

1 set

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Customers also bought

y804 HT-flange sealer 518, 50 ml up to 200°C

Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.

Content: 50 Milliliter (€538.00* / 1000 Milliliter)

€26.90*

94529 HPI Flat head screw M4 x 10 mm

Genuine HPI spare/option part. Dimensions: M4 x 10 mm, 2,5 mm with allen head.Part is delivered in silver or black color from vendor!Contents:10 pieces

€2.30*

Details

7154 FG Body mount adjustable, 1 pce.

Adjustable body mount with heigt-adjustable body support.Measures:Length 110 mmDiameter 8 mm10 mm at the baseFor all cars and body shells.

€9.95*

6558 FG Y-cable Futaba

The Y-cable is required to drive two servos from a single receiver channel.Content:1 piece

€11.10*

2012/500 Linkage set dedicated to Mecatech FW01, complete

Complete set for steering, throttle and brake linkagesSet includes:3 x 6534/02 Throttle pivot post for 2 mm linkages 1 x y0132 y0132 Linkage rod for MecaTech brakes1 x 1213/10 Steel ball 7 x 6,5 mm1 x 66244, Ball joint 7mm M41 x 1213/11 Steering linkage l./r., M4 x 42mm1 x 6020 Set collar 2,1mm1 x 1018/01 Throttle linkage Evo 09 / Comp. 077 x Nut M32 x Screw M3 x 16 mm3 x Screw M3 x 18 mm 2012/501 Throttle linkage 2012/502 Brake linkage set 2012/503 Steering servo linkage set 2012/504 Throttle/brake servo horn The Servo arm is suitable for all servos with an output shaft with 25T spline shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!

€79.90*

y1562 Porsche 911 body shell, Wheelbase 530 mm, clear

Fits on all standard width touring car chassis' with 530 mm wheelbase, FG, Carson C5 chassis and most other 1/5 touring cars with the same wheelbase. The body shell is vac-formed from 2 mm Lexan.Rear wing available in the options menue. Replacement parts: 5192 FG Front Porsche 911 GTR3 R clear 5193 FG Rear Wing Porsche 911 GTR3 R clear Required body mounts:Mount front: FG 8418 Front bumperRear body mount: FG 7152/01 Rear body mountSide body mount front: FG 3014 Body mountsSide body mount rear: FG 3014 Body mountsDimensions:Length: 940 mmWidth: 415 mmHeight: 230 mmWheelbase: 530 mm Painting tips:

€199.90*

y3025 Porsche 911 Vehicle decals for 530 mm Wheelbase

Contains the vehicle specific decals for an original appearance.The set consists of a total of three different decal sheets.For body shell no. y1518 and y1562.Content:1 set

€29.90*

Similar products

y0743 Clutch-Safe 10 g, adhesive especially for clutch pads

Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube

Content: 10 Gramm (€495.00* / 1000 Gramm)

€4.95*

y0730/02 Special wear resistant organic replacement pad

Genuine GPM spare/option part. Use a high strength two-component adhesive (e.g. Clutch-Safe) to glue in the pads and lock them with the countersunk screws M3x5 (part no. y0730/03)Part no. 02 for GPM Big-Scale clutch.For replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731Content:3 pieces

€19.90*

y0730/01 Clutch shoes with pads

Genuine GPM spare/option part. Part no. 01 for GPM Big-Scale clutch. Installation ready set of 3 with glued-on organic pads.Replacing the clutch liningsFor replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731 Content: 3 x aluminum clutch shoes with3 x press-fitted dowel pins (part no. /15) with3 x glued-on organic clutch pads (part no. /02) with3 x M3x5 mm safety screws (part no. /03) installed

€47.90*

y0730/03 Screws for clutch pads M3 x 6 mm

Genuine GPM spare/option part. Part no. 03 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€2.90*

y0730/14 Clutch housing main section

Genuine GPM spare/option part. Part no. 14 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€19.90*

y0730/08 Spring pressure plates, inner side (w/o positioning pin)

Genuine GPM spare/option part. Spring pressure plates, inner side (w/o positioning pin). Part no. 08 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€6.90*

y0730/13 Bushings for clutch shoe pins

Genuine GPM spare/option part. Part no. 13 for GPM Big-Scale clutch.Dimension:Inside diameter: 3 mmOutside diameter: 4,5 mmFlange: 7,2 mmy0730y0731Content:6 pieces

€4.90*

y0730/17 Clutch housing

Genuine GPM spare/option part. Part no. 17 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€22.90*

y0730/10 Adjustment screw M5 x 8 mm

Genuine GPM spare/option part. Part no. 10 for GPM Big-Scale clutch.y0730y0731Content:2 pieces

€1.90*

y0730/04 Spring pressure plates, outer side (with positioning pin)

Genuine GPM spare/option part. Part no. 04 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€8.90*

y0739/01 Spare aluminum clutch shoes, set of three

Aluminum clutch shoes, spare part for GPM BigScale Alu clutch # y0739.Slight aluminum deposits in the clutch bell and corresponding wear marks in the clutch shoes are normal with the Big Scale ALLOY clutch and have no negative effect on the function. Caution: It is very important that when swapping the full-aluminum clutch shoes against the organic friction pads of a Big Scale CROSS or RACE to use a different or new , because the rough surface of the aluminum deposits in the clutch bell left by the Big Scale ALLOY will cause a high wear on the organic pads.

€44.90*

y0730/05 Replacement spring silver 1.3 mm, off-road stock

Genuine GPM spare/option part. Equipped with the silver 1.3 mm springs the Big-Scale clutch provides relatively low slippage and easily controllable clutch engagement at medium rpms.Part no. 05 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€8.90*