Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

y0730/02 Special wear resistant organic replacement pad

Product information "y0730/02 Special wear resistant organic replacement pad"

Genuine GPM spare/option part. 

Use a high strength two-component adhesive (e.g. Clutch-Safe) to glue in the pads and lock them with the countersunk screws M3x5 (part no. y0730/03)

Part no. 02 for GPM Big-Scale clutch.

For replacing the friction pads please proceed as follows:

1. Remove clutch from engine
2. Disassemble clutch
3. Remove the screws fixing the friction pads
4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal
5. Thoroughly degrease the bonding area of clutch shoes and new pads
6. You must use the special adhesive y0743 Clutch-Safe!
7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces
8. Insert the lining into the clutch shoe and align
9. Fix the pad in place with screw y0730/03, just hand-tighten it
10. Remove excessive glue with a rag
11. Preheat oven to 120 °C.
12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down
13. Reassemble clutch and install it onto the engine
14. Wait at least one hour after the gluing process before using the clutch

y0730y0731


Content:
  • 3 pieces

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Accessories / Spare parts

Average rating of 0 out of 5 stars

y0743 Clutch-Safe 10 g, adhesive especially for clutch pads
Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube

Content: 10 Gramm (€495.00* / 1000 Gramm)

€4.95*

Average rating of 0 out of 5 stars

y0730/01 Clutch shoes with pads
Genuine GPM spare/option part. Part no. 01 for GPM Big-Scale clutch. Installation ready set of 3 with glued-on organic pads.Replacing the clutch liningsFor replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731 Content: 3 x aluminum clutch shoes with3 x press-fitted dowel pins (part no. /15) with3 x glued-on organic clutch pads (part no. /02) with3 x M3x5 mm safety screws (part no. /03) installed

€47.90*

Average rating of 0 out of 5 stars

y0730/03 Screws for clutch pads M3 x 6 mm
Genuine GPM spare/option part. Part no. 03 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€2.90*

Average rating of 0 out of 5 stars

y0730/04 Spring pressure plates, outer side (with positioning pin)
Genuine GPM spare/option part. Part no. 04 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€8.90*

Average rating of 0 out of 5 stars

y0730/05 Replacement spring silver 1.3 mm, off-road stock
Genuine GPM spare/option part. Equipped with the silver 1.3 mm springs the Big-Scale clutch provides relatively low slippage and easily controllable clutch engagement at medium rpms.Part no. 05 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€8.90*

Average rating of 0 out of 5 stars

y0730/06 Replacement spring gold 1.4 mm
Genuine GPM spare/option part. Equipped with the gold 1.4 mm springs the Big-Scale clutch provides medium slippage and noticeable clutch engagement at medium to higher rpms. On-road clutch standards.Part no. 06 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€8.90*

Average rating of 0 out of 5 stars

y0730/08 Spring pressure plates, inner side (w/o positioning pin)
Genuine GPM spare/option part. Spring pressure plates, inner side (w/o positioning pin). Part no. 08 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€6.90*

Average rating of 0 out of 5 stars

y0730/09 Adjustment cam Big-Scale clutch
Genuine GPM spare/option part. Part no. 09 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€18.90*

Average rating of 0 out of 5 stars

y0730/10 Adjustment screw M5 x 8 mm
Genuine GPM spare/option part. Part no. 10 for GPM Big-Scale clutch.y0730y0731Content:2 pieces

€1.90*

Average rating of 0 out of 5 stars

y0730/12 CSH screws M3 x 8 mm
Genuine GPM spare/option part. y0730y0731Part no. 12 for GPM Big-Scale clutch. M3 x 8 mm for clutch housing.Content:3 pieces

€1.90*

Average rating of 0 out of 5 stars

y0730/13 Bushings for clutch shoe pins
Genuine GPM spare/option part. Part no. 13 for GPM Big-Scale clutch.Dimension:Inside diameter: 3 mmOutside diameter: 4,5 mmFlange: 7,2 mmy0730y0731Content:6 pieces

€4.90*

Average rating of 0 out of 5 stars

y0730/14 Clutch housing main section
Genuine GPM spare/option part. Part no. 14 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€19.90*

Average rating of 0 out of 5 stars

y0730/17 Clutch housing
Genuine GPM spare/option part. Part no. 17 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€22.90*

Customers also bought

Average rating of 0 out of 5 stars

y0743 Clutch-Safe 10 g, adhesive especially for clutch pads
Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube

Content: 10 Gramm (€495.00* / 1000 Gramm)

€4.95*

Average rating of 0 out of 5 stars

y0730/01 Clutch shoes with pads
Genuine GPM spare/option part. Part no. 01 for GPM Big-Scale clutch. Installation ready set of 3 with glued-on organic pads.Replacing the clutch liningsFor replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731 Content: 3 x aluminum clutch shoes with3 x press-fitted dowel pins (part no. /15) with3 x glued-on organic clutch pads (part no. /02) with3 x M3x5 mm safety screws (part no. /03) installed

€47.90*

Average rating of 0 out of 5 stars

y0730/03 Screws for clutch pads M3 x 6 mm
Genuine GPM spare/option part. Part no. 03 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€2.90*

Average rating of 0 out of 5 stars

y19302/01 Flywheel and Clutch puller CY, Zenoah, HPI, Losi
Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece

€17.90*

Average rating of 0 out of 5 stars

7100 FG Adjusting clip for 16 mm axle, 16 pcs.
These adjusting clips allow a faster adjustment of the wishbones. Suitable for front and rear suspension. The set contains 16 adjusting clips in 2 and 6mm size for 6 mm axles.

€9.50*

Average rating of 0 out of 5 stars

7020/05 FG Front bumper for CLK-DTM
Genuine FG spare/option part. Suitable for CLK-DTM.Dimensions:Length: 100 mmWidth: 360 mmContents:1 piece

€29.90*

Similar products

Average rating of 0 out of 5 stars

y0730/10 Adjustment screw M5 x 8 mm
Genuine GPM spare/option part. Part no. 10 for GPM Big-Scale clutch.y0730y0731Content:2 pieces

€1.90*

Average rating of 0 out of 5 stars

y0743 Clutch-Safe 10 g, adhesive especially for clutch pads
Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube

Content: 10 Gramm (€495.00* / 1000 Gramm)

€4.95*

Average rating of 0 out of 5 stars

y0730/01 Clutch shoes with pads
Genuine GPM spare/option part. Part no. 01 for GPM Big-Scale clutch. Installation ready set of 3 with glued-on organic pads.Replacing the clutch liningsFor replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731 Content: 3 x aluminum clutch shoes with3 x press-fitted dowel pins (part no. /15) with3 x glued-on organic clutch pads (part no. /02) with3 x M3x5 mm safety screws (part no. /03) installed

€47.90*

Average rating of 0 out of 5 stars

y0730/03 Screws for clutch pads M3 x 6 mm
Genuine GPM spare/option part. Part no. 03 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€2.90*

Average rating of 0 out of 5 stars

y0730/14 Clutch housing main section
Genuine GPM spare/option part. Part no. 14 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€19.90*

Average rating of 0 out of 5 stars

y0739/01 Spare aluminum clutch shoes, set of three
Aluminum clutch shoes, spare part for GPM BigScale Alu clutch # y0739.Slight aluminum deposits in the clutch bell and corresponding wear marks in the clutch shoes are normal with the Big Scale ALLOY clutch and have no negative effect on the function. Caution: It is very important that when swapping the full-aluminum clutch shoes against the organic friction pads of a Big Scale CROSS or RACE to use a different or new , because the rough surface of the aluminum deposits in the clutch bell left by the Big Scale ALLOY will cause a high wear on the organic pads.

€44.90*

Average rating of 0 out of 5 stars

y0730/08 Spring pressure plates, inner side (w/o positioning pin)
Genuine GPM spare/option part. Spring pressure plates, inner side (w/o positioning pin). Part no. 08 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€6.90*

Average rating of 0 out of 5 stars

y0730/13 Bushings for clutch shoe pins
Genuine GPM spare/option part. Part no. 13 for GPM Big-Scale clutch.Dimension:Inside diameter: 3 mmOutside diameter: 4,5 mmFlange: 7,2 mmy0730y0731Content:6 pieces

€4.90*

Average rating of 0 out of 5 stars

y0730/17 Clutch housing
Genuine GPM spare/option part. Part no. 17 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€22.90*

Average rating of 0 out of 5 stars

y0730/04 Spring pressure plates, outer side (with positioning pin)
Genuine GPM spare/option part. Part no. 04 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€8.90*

Average rating of 0 out of 5 stars

y0730/05 Replacement spring silver 1.3 mm, off-road stock
Genuine GPM spare/option part. Equipped with the silver 1.3 mm springs the Big-Scale clutch provides relatively low slippage and easily controllable clutch engagement at medium rpms.Part no. 05 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€8.90*

Average rating of 0 out of 5 stars

y0730/18 Mounting bolt for GPM and Lauterbacher clutch
Genuine GPM spare/option part. Mountig bolt fits GPM 3-shoe clutches y0730 / y0731 and Lauterbacher clutch 50481.y0730y0731Content:3 pieces

€3.90*

Customers also viewed

Average rating of 0 out of 5 stars

y0730/14 Clutch housing main section
Genuine GPM spare/option part. Part no. 14 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€19.90*

Average rating of 0 out of 5 stars

y0743 Clutch-Safe 10 g, adhesive especially for clutch pads
Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube

Content: 10 Gramm (€495.00* / 1000 Gramm)

€4.95*

Average rating of 0 out of 5 stars

3000-15 Mecatech Expert brake pad - 4 pcs.

€39.90*

Average rating of 0 out of 5 stars

Mielke 5541 Power Gearshift clutch for FG (except Formula 1+Evo2020), Harm, RS5, Mix, 2,4mm springs with long clutch carrier
The new adjustable system features two aluminum and one carbon pad with special 2.4 mm springs.Weight of the complete clutch is 70 grams. Very wear resistent when running with the recommended clutch bells.Adjustable friction points: First gear - 8.500 U/min. Second gear - 9.300 U/min. Third gear - 10.100 U/min. Fourth gear - 11.000 U/min.With tool #5445 the engagement speed can be adjusted to different settings within a range from about 8,500 to 11,000 rpm.For RS5 models from version T14!

€129.50*

Average rating of 0 out of 5 stars

y0730/01 Clutch shoes with pads
Genuine GPM spare/option part. Part no. 01 for GPM Big-Scale clutch. Installation ready set of 3 with glued-on organic pads.Replacing the clutch liningsFor replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731 Content: 3 x aluminum clutch shoes with3 x press-fitted dowel pins (part no. /15) with3 x glued-on organic clutch pads (part no. /02) with3 x M3x5 mm safety screws (part no. /03) installed

€47.90*

Average rating of 0 out of 5 stars

7316 FG Clutch blocks for Zenoah
Genuine FG spare/option part. Zenoah bolts 7318 are required for installation.Content:2 pieces

€19.90*
Loading...
Upload in progress, please be patient ...
Shopware-Theme Development Shopware-Plugin Development