y0739/01 Spare aluminum clutch shoes, set of three

€44.90*

Available

Product number: y0739_01

EAN: 4058575047629

Product information "y0739/01 Spare aluminum clutch shoes, set of three"

Aluminum clutch shoes, spare part for GPM BigScale Alu clutch # y0739.

Slight aluminum deposits in the clutch bell and corresponding wear marks in the clutch shoes are normal with the Big Scale ALLOY clutch and have no negative effect on the function.

Caution:

It is very important that when swapping the full-aluminum clutch shoes against the organic friction pads of a Big Scale CROSS or RACE to use a different or new , because the rough surface of the aluminum deposits in the clutch bell left by the Big Scale ALLOY will cause a high wear on the organic pads.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

y0730/10 Adjustment screw M5 x 8 mm

Genuine GPM spare/option part. Part no. 10 for GPM Big-Scale clutch.y0730y0731Content:2 pieces

€1.90*

y0743 Clutch-Safe 10 g, adhesive especially for clutch pads

Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube

Content: 10 Gramm (€495.00* / 1000 Gramm)

€4.95*

y0730/02 Special wear resistant organic replacement pad

Genuine GPM spare/option part. Use a high strength two-component adhesive (e.g. Clutch-Safe) to glue in the pads and lock them with the countersunk screws M3x5 (part no. y0730/03)Part no. 02 for GPM Big-Scale clutch.For replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731Content:3 pieces

€19.90*

Details

y0730/14 Clutch housing main section

Genuine GPM spare/option part. Part no. 14 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€19.90*

Details

y0730/03 Screws for clutch pads M3 x 6 mm

Genuine GPM spare/option part. Part no. 03 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€2.90*

y0730/05 Replacement spring silver 1.3 mm, off-road stock

Genuine GPM spare/option part. Equipped with the silver 1.3 mm springs the Big-Scale clutch provides relatively low slippage and easily controllable clutch engagement at medium rpms.Part no. 05 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€8.90*

y0730/06 Replacement spring gold 1.4 mm

Genuine GPM spare/option part. Equipped with the gold 1.4 mm springs the Big-Scale clutch provides medium slippage and noticeable clutch engagement at medium to higher rpms. On-road clutch standards.Part no. 06 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€8.90*

y0730/12 CSH screws M3 x 8 mm

Genuine GPM spare/option part. y0730y0731Part no. 12 for GPM Big-Scale clutch. M3 x 8 mm for clutch housing.Content:3 pieces

€1.90*

y0730/09 Adjustment cam Big-Scale clutch

Genuine GPM spare/option part. Part no. 09 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€18.90*

y0730/19 Full-aluminum clutch shoes conversion kit

Genuine GPM spare/option part. Full aluminum clutch shoes are very successfully used in 1/5 onroad racing applications.Therefore we can now offer the GPM conversion kit for BigScale Cross/Race clutches to full-aluminum clutch shoes. Made of a special alloy to suit this application the kit comes with 1.4 mm wire diameter springs and new spring pressure plates.Slight aluminum deposits in the clutch bell and corresponding wear marks in the clutch shoes are normal with the Big Scale ALLOY clutch and have no negative effect on the function. Caution: It is very important that when swapping the full-aluminum clutch shoes against the organic friction pads of a Big Scale CROSS or RACE to use a different or new , because the rough surface of the aluminum deposits in the clutch bell left by the Big Scale ALLOY will cause a high wear on the organic pads.y0730y0731Content:1 set

€54.90*

y0730/18 Mounting bolt for GPM and Lauterbacher clutch

Genuine GPM spare/option part. Mountig bolt fits GPM 3-shoe clutches y0730 / y0731 and Lauterbacher clutch 50481.y0730y0731Content:3 pieces

€3.90*

y0730/21 Spring pressure plates for GPM BigScale clutches

Genuine GPM spare/option part. Spare spring pressure plates for GPM clutches BigScale EXTREME # y0733 and ALU # y0739.y0730y0731Content:3 pieces

€9.90*

Customers also viewed

Samba MOCA Cruze 1/5 TC bodyshell clear 1mm

Genuine Samba spare/option part. The body shell is neither cut nor drilled, clear and can therefore be adopted to all touring cars with a 530/535 mm wheelbase.We have decided to make a new TC bodyshell to offer a new car from the WTTC series for the 5th scale drivers.Currently the most sought after large scale body shell with optimal aerodynamicsMaterial thickness 1 mm. The body shell consists of one part.Precut, the final cutting must be made according to the chassis you use it on.Width front / rear: 392 mm.Contents:1 piece

€89.90*

6061 Mielke pull starter with hybrid starter function

Genuine Mielke spare / option part.Starting by pull starter or by cordless screwdriver or electric starter is possible.Pull starter with hybrid starter function. Who does not know it? A torn starter rope, blisters on your finger from constant pulling or a defective starter pawl. All these problems are a thing of the past with the hybrid starter.With the help of a cordless screwdriver the engine can be started very easily and if the battery of the cordless screwdriver is empty, the engine can be started by using the conventional way with the pull-rope starter.Please note:The starter shaft for electric start is inserted in a straight line in extension of the crankshaft. No part of the vehicle must be in the way here. On a model with a longitudinally mounted engine (e.g. Losi 5ive or DBXL vehicles) the rear axle will usually prevent the use of the electric start. The normal pull start by cable remains possible.Contents:1 piece

€114.90*

y1330 BMW 320si WTCC 1/5 body shell, painted, 535 wheelbase, white/light blue

Genuine HT spare/option part.Fits 535 mm wheel base, current touring car width. A rear wing is available through the shop's options menu. The body shell comes without decals!Required body mounts:Front section: FG 7020/11 Front bumperRear body mount: FG 7152/01 Rear body supportSide front: FG 7012 Body mountSide rear: FG 7014 Body mountAvailable decal sheets:y1329 - Vehicle decalsy1320/01 - Team decals Posty1329/02 - Team decals Samsungy1329/03 - BMW-Bank decalsy0683 - Jägermeister decalsy3006 - rc-car-online decalsDimensions:Length: 885 mmWidth: 392 mmHeight: 260 mmWheel base: 530 mm

€99.90*

7313/01 FG Key for Crankshaft for CY / Zenoah / Fuelie

Genuine FG spare/option part. Contents:1 piece

€3.70*

y1436 SPEED TEC CRANK Ignition-System (CIS)

y1436 Tools: Booth tools+ 49.9EUR

New ignition system for RC Car race engines with air baffles, special 62 mm balanced flywheel, modified ignition coil mount and special Löhin tuning ignition (#1361). For Zenoah G230/240/260/270/290/320 und CY / Fuelie / Losi engines.A much smaller and lighter flywheel, in conjunction with the special air baffles, ensures that the engine gets more cooling air then with previously available modified flywheels! The fan from the CIS-ignition with fins on both sides is about 30% lighter (!) than the stock version! Needless to say an engine equipped with such a flywheel revs considerably faster and significantly higher, of course. This in itself is nothing new, because modified flywheels, even though not 30% lighter, are pretty common on modified engines. However, the problem with these modified flywheels is maintaining sufficient cooling for the engine, which is absolutely mandatory for a reliably running engine! The 20% smaller in diameter flywheel is primarily responsible for the very substantial performance increase by the SPEED TEC CRANK ignition . The lower inertia, which is quite crucial for engine performance, allows for an extremely fast and higher revving engine! The air baffles of the CIS-ignition ensure that the path of the cooling air is matched to the reduced diameter of the CIS-fan wheel and the engine gets more cooling! As our product video shows, the stock engine gained near 2,000 rpm through installation of the SPEED TEC CIS-ignition ! But perhaps the optimized torque is even more convincing. This for 30% reduced and 20% more centrally positioned flywheel mass gives your engine a stunning power increase. Other benefits of SPEED TEC CIS - ignition system: Fits all Zenoah, as well as HPI, Losi-, CY 1/5 & 1/6 engines (incl. Zenoah G320) No modifications to the cylinder or the ignition coil mount required! No assembly of the flywheel, thus 100% exact fit and running true The enclosed Löhin ignition system is designed for speeds up to 25,000 rpm! The baffles protect the flywheel from debris (stones, etc.) Complete with Löhin ignition and all necessary parts in a nice special bag Easy installation: Remove the stock ignition system - install the CIS-ignition - done! The color of the ignition cable and the spark plug cap may vary.

Variants from €329.00*

€378.90*

Details