Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

y0743 Clutch-Safe 10 g, adhesive especially for clutch pads

Product information "y0743 Clutch-Safe 10 g, adhesive especially for clutch pads"

Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!)

Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!)

The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended.

For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.

Attention:
  • Clutch-Safe adhesive must be stored in the fridge!


Content:
10g tube

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

Average rating of 0 out of 5 stars

y0730/02 Special wear resistant organic replacement pad
Genuine GPM spare/option part. Use a high strength two-component adhesive (e.g. Clutch-Safe) to glue in the pads and lock them with the countersunk screws M3x5 (part no. y0730/03)Part no. 02 for GPM Big-Scale clutch.For replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731Content:3 pieces

€19.90*

Average rating of 0 out of 5 stars

y0730/01 Clutch shoes with pads
Genuine GPM spare/option part. Part no. 01 for GPM Big-Scale clutch. Installation ready set of 3 with glued-on organic pads.Replacing the clutch liningsFor replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731 Content: 3 x aluminum clutch shoes with3 x press-fitted dowel pins (part no. /15) with3 x glued-on organic clutch pads (part no. /02) with3 x M3x5 mm safety screws (part no. /03) installed

€47.90*

Average rating of 0 out of 5 stars

y0730/03 Screws for clutch pads M3 x 6 mm
Genuine GPM spare/option part. Part no. 03 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€2.90*

Average rating of 0 out of 5 stars

y19302/01 Flywheel and Clutch puller CY, Zenoah, HPI, Losi
Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece

€17.90*

Average rating of 0 out of 5 stars

7100 FG Adjusting clip for 16 mm axle, 16 pcs.
These adjusting clips allow a faster adjustment of the wishbones. Suitable for front and rear suspension. The set contains 16 adjusting clips in 2 and 6mm size for 6 mm axles.

€9.50*

Average rating of 0 out of 5 stars

y1210 HT Aluminum front bulkhead B for FG, Carson/Smartech, Reely 2WD
Genuine HT spare/option part.With replaceable bushings for the hinge pins.Fits Comanche, Attack Evo, CRT 2WD, CPT, C5, R5, FG Sportsline and Smartech. Contents:1 piece

€49.90*

Similar products

Average rating of 0 out of 5 stars

y0733/061 Clutch spring green, 1.4 mm, 3 pcs.
Clutch spring green, 1.4 mm, optional part for BigScale Extreme clutch.

€9.90*

Average rating of 0 out of 5 stars

y0733/065 Clutch spring candy red, 1.8 mm, 3 pcs.
Clutch spring candy red, 1.8 mm, optional part for BigScale Extreme clutch.

€9.90*

Average rating of 0 out of 5 stars

y0733/01 Clutch shoes with bonded organic friction pads
Clutch shoes with bonded organic friction pads for BigScale Extreme clutch.

€54.90*

Average rating of 0 out of 5 stars

y0733/04 Pressure plate, 0.8 mm flange
Pressure plate, 0.8 mm flange thickness, spare part for BigScale Extreme clutch.

€9.90*

Average rating of 0 out of 5 stars

y0733/05 Pressure plate, 1.5 mm flange thickness
Pressure plate, 1.5 mm flange thickness, spare part for BigScale Extreme clutch.

€9.90*

Average rating of 0 out of 5 stars

y0733/09 Front plate
Front plate, spare part for BigScale Extreme clutch.

€19.90*

Average rating of 0 out of 5 stars

y0733/064 Clutch spring orange, 1.7 mm, 3 pcs.
Clutch spring orange, 1.7 mm, optional part for BigScale Extreme clutch.

€9.90*

Average rating of 0 out of 5 stars

y0733/02 Extremely wear resistant organic friction pad
Extremely wear resistant organic friction pad, spare part for BigScale Extreme clutch.Since the connection between lining and shoe is highly loaded, the careful bonding with curing in an oven is of particular importance. Please use exclusively the special Clutch-Safe glue #y0743.You can find ready-to use cluth shoes with correctly bonded friction pads under at # y0733/01.

€19.90*

Average rating of 0 out of 5 stars

y0733/08 Clutch body
Clutch body, spare part for BigScale Extreme clutch.

€29.90*

Average rating of 0 out of 5 stars

y0733/062 Clutch spring black, 1.5 mm, 3 pcs.
Clutch spring black, 1.5 mm, spare part for BigScale Extreme clutch, stock spring.

€9.90*

Average rating of 0 out of 5 stars

y0733/07 Adjustment screw M5x7.6 mm, 3 pcs.
Adjustment screw M5x7.6 mm, spare part for BigScale Extreme clutch (2.5 mm allen wrench size).

€9.90*

Average rating of 0 out of 5 stars

y0733/063 Clutch spring white, 1.6 mm, 3 pcs.
Clutch spring white, 1.6 mm, optional part for BigScale Extreme clutch.

€9.90*

Customers also viewed

Average rating of 0 out of 5 stars

y0733/061 Clutch spring green, 1.4 mm, 3 pcs.
Clutch spring green, 1.4 mm, optional part for BigScale Extreme clutch.

€9.90*

Average rating of 0 out of 5 stars

y0730/01 Clutch shoes with pads
Genuine GPM spare/option part. Part no. 01 for GPM Big-Scale clutch. Installation ready set of 3 with glued-on organic pads.Replacing the clutch liningsFor replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731 Content: 3 x aluminum clutch shoes with3 x press-fitted dowel pins (part no. /15) with3 x glued-on organic clutch pads (part no. /02) with3 x M3x5 mm safety screws (part no. /03) installed

€47.90*

Average rating of 0 out of 5 stars

Z159 HPI Thread lock
Genuine HPI spare/option part. An excellent recommendation for removal of screws treated with threadlocking compound: y1007 CFH Diamant M50 Gasbrenner<Contents:1 piece / 3 ml

Content: 3 Milliliter (€1,826.67* / 1000 Milliliter)

€5.48*

Average rating of 0 out of 5 stars

7315 FG Clutch block carrier Zenoah
Genuine FG spare/option part. Content:1 piece

€9.40*

Average rating of 0 out of 5 stars

y1016/003 Transfer port cover plate, clutch side G320RC
Genuine Zenoah spare/option part. Replacement part fits Zenoah G320RC.

€5.90*

Average rating of 0 out of 5 stars

y0733/03 Mounting screws for friction pads and front plate
Mounting screws for friction pads and front plate, spare part for BigScale Extreme clutch.Dimensions:M3 x 7 mm (f0r 2 mm allen wrench)

€3.90*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Theme Development