SPMS906 Spektrum S906 1/5 DBXL-E Servo 30kg

CYS S0650, a digital large scale servo with very robust steel gears. It offers a lot of power at good speed. Its a direct fit for cars like Losi 5ive and DBXL, UFRC Growler GX1, FG and so on.Technical data: Operating voltage: 6V-7.4V Operating speed (6.0 V): 0.13 s / 60 degrees Operating speed (7.4 V): 0.11 s / 60 degrees Holding torque (6.0V): 470 Ncm holding torque (7.4V): 539 Ncm Cable: Universal/JR connector, approx. 300mm Gear material: 1st stage brass, all others steel Bearing: 2 x ball bearing Size: 66 x 30 x 56mm Weight: 204 grams Double sided servo arm 68mm length Guide sleeve 4 pieces Mounting screws 4 pieces Mounting screws for servoarm 1 piecesContents:1 piece

y2006 Top Tuning Digital pro 40 kg is a digital large scale servo with a very robust metal gears.It offers a lot of power at good speed and has a metal housing with side cooling fins.Its installation dimensions fit directly for FG, Losi, HPI and various other models! Dimensions identical to: Multiplex Rhino - Servo 32 kg FG Mega - Servo ST2605 30 kg Spectrum SPMS904WP 34 kg Spectrum SPMS904HV 18 kg Technical data: Classification: large scale servo Dimensions LxWxH (mm): 59.5 x 29.2 x 55.2 mm Operating voltage: 6 volts / 7.4 volts Torque: (Ncm): 380/400 Speed (sec / 60 °): 0.20 / 0.18 Number of ball bearings: 2 Servo gear: metal gears Seals: 3 (splash-protected) Silicone cable: with universal plug, 300 mm long Weight: 146 grams Brass output shaft 17T spline Content: 1 piece of TopTuning Digital pro servo 40 kg 1 piece double sided servo arm 70 mm total 1 piece of 40 mm single sided servo arm 4 pieces of guide sleeves 4 pieces of rubber grommets 4 pieces of fastening screws

Genuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece

Power 48 kg with a 6V battery, 62 kg with 2S LiPoDimensions: length 66 mm x width 30 mm x height 56 mmOutput shaft 15T splineContents:1 piece

The RHINO pro SHV digi 4 servo is a 29 mm digital servo designed for use in large-scale models. The new pro SHV servo is faster, more powerful, and more durable than the proven RHINO digi 4, of which thousands are now in use. More performance, with higher torque and faster transit speed, and more durable with a new triple-ballraced heavy-duty steel gear set. The operating voltage range has been expanded to 7.4 V, allowing the servo to be operated directly with up to two-cell LiPo batteries.Large 1 : 5 scale model cars make very exacting demands on the servos, and for many years the RHINO servo has set the standard with its extremely robust, outsize metal gearbox and 8 mm output shaft for the output device. An integral aluminium heat-sink cools the motor and electronics very effectively. Servo case gaskets make the unit dust-proof and splash-proof. The enormous power and robust nature of this servo also make it an excellent choice for large models generally, such as F3A - XXL large-scale model aircraft, as well as for non-standard applications.Adapter FG # 6118/02 is required for installation into a FG/Smartech car.High-voltage (HV) servosHV servos have a broad operating voltage range of 5 - 7.4 V, i.e. they can be operated directly with two-cell Lithium-based rechargeable batteries (e.g. LiPo, LiFe, LiIo). The outstanding features of LiXX batteries compared with NiXX types are their higher energy density and lower self-discharge rate, and for these reasons they are increasingly used as power supplies in model RC systems. The higher voltage of LiXX batteries means that the current drawn by an HV servo is lower for a given output power than that of conventional servos, which are generally designed for a nominal voltage of 4.8 - 6 V. When used with 2S LiXX batteries, these older servos must therefore be operated with a separate voltage reducer. This reduces the overall efficiency of the system, leads to unnecessary dissipated power, requires additional electronic complexity and more connectors ( higher costs, greater failure risk, higher weight). Modern receivers (e.g. M-LINK) are designed for voltages up to 9 V, i.e. with HV there is no longer any reason not to use the modern, superior LiXX battery technology.The following servo parameters can be adjusted using the MULTImate test and programming unit # 8 2094:Direction of servo rotationServo transit speedServo travel, left / right (max. 2 x 90°)Servo centreServo deadbandFail-safe (On with servo Fail-Safe position / Off)Reset to factory default settingsSpecificationDimensions (L x W x H):Weight::Gearbox:Ballraces:Multi-finger wiper pot:Torque @ 6 V / 7f.4 V*:Holding power @ 6 V / 7.4 V*:Transit speed for 40°@ 6 V / 7.4 V*: 59 x 29 x 55 mm172 gSteel3yes (with indirect drive)230 / 270 Ncm280 / 320 Ncm** 0,10 / 0,08 sec.* 5-cell NiXX / 2S LiPo operation. Values measured at stabilised 6.0 V / 7.4 V.** Holding power at angular error

Genuine rc-car-online spare/option part. Compatible with up to 8S lithium batteries. In addition to the LiPo Tester, the CellMeter also has a built-in servo tester. This makes it possible to check at any time whether the servos are working properly.Technical data:High visibility LCD displayBalancer functionDischarge functionVery accurate battery checkSuitable for Li-Ion, LiPo, LiFe, LiHv, NiCd, NiMh batteries (up to 8 cells)Battery type and Zellenanzahl will be recognized automaticallyVoltage displayed individually for every cellWeight: 48gDimensions LxWxH: 84 mm x 52 mm x 15 mmContents:1 piece

Genuine FG spare/option part. Heavy duty servos 2WD and 4WD 1/5 and 1/6 models. Ball-bearinged with metal gears.Speed: 0.22s-0.20s/60°Torque: 26 - 28kg/cmDimensions : 59,5 x 29,5 x 51,3 mmVoltage: 6.0-7.4VWeight: 154gContents:1 piece

Genuine Losi spare/option part.Specifications Torque: 346 Ncm Speed: 0.216 sec @ 6v Length: 2.33 in (59,1 mm) Width: 1.14 in (29 mm) Height: 2.16 in (54,9 mm) Splint count: 15 toothContents:1 piece

Genuine Spektrum spare/option part. Output shaft 8 mm 15T spline.Specifications: Torque:496 oz-inSpeed:0.216 sec @ 6v Length:2.33 in (59.1mm) Width:1.14 in (29mm) Height:2.16 inch (54.9mm) Contents:1 piece

Fits 5ive-T 2.0 as well!Set includes:Hitec Servo HS-1100WPy1378 Dymond LiPo special high current receiver battery 14.8V/2400mAhy1306 - JETI-SBEC 6-42V voltage regulatory1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 - Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 - Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 - All steel linkage steering servo/servo saver applicationy1378 - LiPo special high current receiver battery 14.8V/2200mAhGenuine FG spare/option part. This battery is especially for use in vehicles which are equipped with the Hitec Servo HS-900SGS/HS-1000SGT/1005SGT/HS-1100WP for external high-voltage power supply. This battery comes with a Y-adaptor harness for two connectors, one each JST and Futaba/Universal connector. The JST connector is used for hooking up to the steering servo; the universal connector is used for the voltage regulator. The battery fits into the standard battery box of the Losi 5ive-T. Dimensions:Length: 110 mmWidth: 32 mmHeight: 33 mmWeight: 247 grConfiguration: 4S1pCurrent rating: 40C (66 A)Recommended charging current: up to 3C (2.2 A)XHP(XH) -balancer connector To increase the battery's life span it is recommended to use a charging current of approx. 0.8 A for the first three cycles.Contents:1 piecey1306 - Servo voltage regulatorThe switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piecey1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT Losi 5ive-TGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1309 - All steel linkage for Losi 5ive-T steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 pieceHitec Servo HS-1100WPGenuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece

Genuine Carson spare/option part. DimensionsLenght approx 63mmWidth approx 33mmHeight approx 55mmThe stronger alternative:K-Power DM4000 Servo 54kg-cm/0,11 s/6 Volt till 8,4 volt 89,90 EURHowever, the installation requires some "rework" on the servo mount!Contents:1 piece

CYS S0650, a digital large scale servo with very robust steel gears. It offers a lot of power at good speed. Its a direct fit for cars like Losi 5ive and DBXL, UFRC Growler GX1, FG and so on.Technical data: Operating voltage: 6V-7.4V Operating speed (6.0 V): 0.13 s / 60 degrees Operating speed (7.4 V): 0.11 s / 60 degrees Holding torque (6.0V): 470 Ncm holding torque (7.4V): 539 Ncm Cable: Universal/JR connector, approx. 300mm Gear material: 1st stage brass, all others steel Bearing: 2 x ball bearing Size: 66 x 30 x 56mm Weight: 204 grams Double sided servo arm 68mm length Guide sleeve 4 pieces Mounting screws 4 pieces Mounting screws for servoarm 1 piecesContents:1 piece

y2006 Top Tuning Digital pro 40 kg is a digital large scale servo with a very robust metal gears.It offers a lot of power at good speed and has a metal housing with side cooling fins.Its installation dimensions fit directly for FG, Losi, HPI and various other models! Dimensions identical to: Multiplex Rhino - Servo 32 kg FG Mega - Servo ST2605 30 kg Spectrum SPMS904WP 34 kg Spectrum SPMS904HV 18 kg Technical data: Classification: large scale servo Dimensions LxWxH (mm): 59.5 x 29.2 x 55.2 mm Operating voltage: 6 volts / 7.4 volts Torque: (Ncm): 380/400 Speed (sec / 60 °): 0.20 / 0.18 Number of ball bearings: 2 Servo gear: metal gears Seals: 3 (splash-protected) Silicone cable: with universal plug, 300 mm long Weight: 146 grams Brass output shaft 17T spline Content: 1 piece of TopTuning Digital pro servo 40 kg 1 piece double sided servo arm 70 mm total 1 piece of 40 mm single sided servo arm 4 pieces of guide sleeves 4 pieces of rubber grommets 4 pieces of fastening screws

Genuine Mecatech spare/option part.New design for the Active Diff! It is lighter, smaller and it haven´t the adjustment screw. The inner parts are the same of the standard version.Heavy-duty, torque dependent self-locking differential with various possibilities for adjustment.The use of four satellite gears distributes the load on four ramps, increasing their service life compared to already existing solutions. Needle bearings on the back of the satellite gears ensure smooth operation of the ramp system.For adaption to the grip conditions you can choose from two different pairs of steel and carbon friction disks and ramp bells. The latter have 3 different ramp angles per pair of bells. All versions are included.Differential spur gear and ball bearings are vehicle-dependent and therefore not included.Content:1 x complete Mecatech Active Diff assembled with bell B for high grip2 x bell A for low grip4 x Carbon discs outer diameter 30 mm4 x Steel discs inner diameter 24 mm1 x Bottle of diff oil

Genuine Graupner/Spektrum Z590 servo, fully warranted.Torque 60 Ncm, speed 0,12 sec. dimensions 38 x 18,5 x 37 mm. Metal gears, ballraced.

Genuine Losi spare/option part. Fully assembled and filled rear bumper for the Super Baja Rey.Contents:2 pieces

Includes HT-Edition parts set worth over 150.- , consisting of:: TT1000 Top Tuning Electronic 20 Amp Bigscale high voltage 30 Volt switch TT1000 Top Tuning Electronic 20 Amp Bigscale high voltage 30 y0558 HT Car Bag XXL for Losi 5ive-T/2.0, Mini 5ive WRC, Desert Buggy XL and many more   y0558 HT Car Bag XXL für Losi y1312 Twin hose bracket 3 pieces y1312 Twin hose bracket When the original 5IVE-T was introduced the world of 1/5-scale off-road racing changed, and this iconic platform became one of the most successful and influential platforms to date. Now get ready for 2.0! The Losi 5IVE-T 2.0 BND: 1/5 4WD Gas Short Course Truck has all of the unrivaled performance of its predecessor and includes Bind-N-Drive technology, allowing you to pick the transmitter that best fits your lifestyle. The powerful Zenoah G320 32cc engine has been built specifically for the 5IVE-T 2.0.The revised chassis layout reduces the front drive shaft angle for improved durability and increased 4WD balance. Plus, the new rack style bellcrank steering assembly makes for easy Ackermann changes and overall improved steering geometry. Additional advances include an updated front hood, upgraded brakes, and hard anodized bleeder caps and shock bodies for improved shock performance. All this ensures the 5IVE-T 2.0 continues to reign supreme.Key FeaturesGenuine Zenoah G320 32cc engineInnovative Bind-N-DriveSpektrum SR6000T telemetry-ready receiverImproved bar style steering rack with adjustable AckermannImproved center differential orientationImproved drive line angleHeavy-duty brakesInnovative clutch mount with gear mesh braceTough steering and gas/throttle servo braceExtra-large 800cc capacity fuel tank What's in the Box?Losi 5IVE-T® 2.0 BND 4WD SCTSpektrum 6200A DSMR 6-Ch AVC Telemetrie receiverZenoah 32cc Gasoline Pull-Start EngineS900S 1/5 Scale Metal Gear Steering ServoS901T 1/5 Scale Metal Gear Throttle ServoWheel WrenchRod End/Shock End toolMulti WrenchSpark Plug WrenchBind PlugExhaust Gasket2.0mm, 2.5mm, 3.0mm, 4.0mm Allen WrenchesProduct Manual Dimensions Height: 181 mm Length: 965 mm Width: 520 mm Weight: 17 kg Needed to CompleteAppropriate Charger like DYNC0505WTransmitter / receiver eg: DX2E or serial receiver compatible e.g: DX6R87-92 Octane Gasoline2-Cycle Motul Oil e.g: y0813/02Gas can e.g: y0686Contents:1 piece