65154 Multiplex Servo Rhino pro SHV digi 4 Angebot

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

Genuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece

Genuine HT spare/option part. 5 cells, 6 volt, cell size Sub-C. More applications on request.Dimensions: approx 112 x 46 x 23 mmContents:1 piece

Servo direct power supply cable, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.Silicone insulated wires with 0.5 mm² cross section

Genuine Losi spare/option part. Contents:1 set

Genuine HT spare/option part. Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.Size: 2.5 x 100 mmHolding strength: 8.1 kgTemperature range: -40°C to +85°CContents:1 piece

CNC-machined from 6061-T6 aluminum by Area RC, significantly stronger and more rigid than any plastic version. The length of the arm is 43 mm. Available in 3 different versions:AREA-XL BJ032/01 with 23 teeth, red for KO PRO, JR, Sanwa, Airtronics- and many other Servos with 23 teeth shaftAREA-XL BJ032/02 with 24 teeth, titan color for KO PRO, JR, Sanwa, Airtronics- and many other Servos with 23 teeth shaft

Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum radio plate from ATOP, fits Losi 5ive-T 1.0 and 2.0.This all-aluminum unit allows for installation of dual steering servos. The servo hole patterns are suitable for Losi original servos / servos with the size of 900S and K-Power.The box for the receiver battery has internal dimensions of 142 x 65 x 32 mm.Available with additional genuine Losi S900S 5ive-T steering servo incl- Y-harness in the options menu.Contents:1 piece

For the secure installation of driveshaft boots.

Fits 5ive-T 2.0 as well!Set includes:Hitec Servo HS-1100WPy1378 Dymond LiPo special high current receiver battery 14.8V/2400mAhy1306 - JETI-SBEC 6-42V voltage regulatory1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 - Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 - Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 - All steel linkage steering servo/servo saver applicationy1378 - LiPo special high current receiver battery 14.8V/2200mAhGenuine FG spare/option part. This battery is especially for use in vehicles which are equipped with the Hitec Servo HS-900SGS/HS-1000SGT/1005SGT/HS-1100WP for external high-voltage power supply. This battery comes with a Y-adaptor harness for two connectors, one each JST and Futaba/Universal connector. The JST connector is used for hooking up to the steering servo; the universal connector is used for the voltage regulator. The battery fits into the standard battery box of the Losi 5ive-T. Dimensions:Length: 110 mmWidth: 32 mmHeight: 33 mmWeight: 247 grConfiguration: 4S1pCurrent rating: 40C (66 A)Recommended charging current: up to 3C (2.2 A)XHP(XH) -balancer connector To increase the battery's life span it is recommended to use a charging current of approx. 0.8 A for the first three cycles.Contents:1 piecey1306 - Servo voltage regulatorThe switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piecey1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT Losi 5ive-TGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1309 - All steel linkage for Losi 5ive-T steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 pieceHitec Servo HS-1100WPGenuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece

Genuine HT spare/option part. Abrasion protection for cables, fuel tubes and hydraulic brake lines. Pack with 1 m. Small, for cables from 1.5 to 8 mm diameter.Contents:1 piece / 1 meter

Servo direct power supply cable with electronic switch, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.The integrated electronic receiver switch is rated 5 A continuous / 15 A peak. This switch does not use mechanical contacts for the load; therefore it is less prone to failure caused by vibrations or dirt. With separate charging connector.With drilling template and mounting material included.

23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230:Quantity of cylinder mounting bolts increased from 2 to 4Improved strength of crankcaseAdded additional bearing on the PTO (clutch) side of crankshaftRedesigned shape of cylinder finsDimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

y2006 Top Tuning Digital pro 40 kg is a digital large scale servo with a very robust metal gears.It offers a lot of power at good speed and has a metal housing with side cooling fins.Its installation dimensions fit directly for FG, Losi, HPI and various other models! Dimensions identical to: Multiplex Rhino - Servo 32 kg FG Mega - Servo ST2605 30 kg Spectrum SPMS904WP 34 kg Spectrum SPMS904HV 18 kg Technical data: Classification: large scale servo Dimensions LxWxH (mm): 59.5 x 29.2 x 55.2 mm Operating voltage: 6 volts / 7.4 volts Torque: (Ncm): 380/400 Speed (sec / 60 °): 0.20 / 0.18 Number of ball bearings: 2 Servo gear: metal gears Seals: 3 (splash-protected) Silicone cable: with universal plug, 300 mm long Weight: 146 grams Brass output shaft 17T spline Content: 1 piece of TopTuning Digital pro servo 40 kg 1 piece double sided servo arm 70 mm total 1 piece of 40 mm single sided servo arm 4 pieces of guide sleeves 4 pieces of rubber grommets 4 pieces of fastening screws

Power 48 kg with a 6V battery, 62 kg with 2S LiPoDimensions: length 66 mm x width 30 mm x height 56 mmOutput shaft 15T splineContents:1 piece

Genuine rc-car-online spare/option part.For most servos with a 15T output shaft.K-Power DM4000Multiplex RhinoHitech 805Savöx SV-0236MGSpectrum S9010 and S9020LOSB 0886 S901T (original Losi 5ive-T throttle/brake servo)LOSB 0884 S900S (original Losi 5ive-T steering servo)and many more! Dimension: Total length: 48 mm Hole distance: 30 mmIf you count the splines on your servo, you can see whether this servo arm will fit.Aluminum servo arms are a must with strong digital servos, as they are used e.g. in large scale cars.Contents:1 piece

CYS S0650, a digital large scale servo with very robust steel gears. It offers a lot of power at good speed. Its a direct fit for cars like Losi 5ive and DBXL, UFRC Growler GX1, FG and so on.Technical data: Operating voltage: 6V-7.4V Operating speed (6.0 V): 0.13 s / 60 degrees Operating speed (7.4 V): 0.11 s / 60 degrees Holding torque (6.0V): 470 Ncm holding torque (7.4V): 539 Ncm Cable: Universal/JR connector, approx. 300mm Gear material: 1st stage brass, all others steel Bearing: 2 x ball bearing Size: 66 x 30 x 56mm Weight: 204 grams Double sided servo arm 68mm length Guide sleeve 4 pieces Mounting screws 4 pieces Mounting screws for servoarm 1 piecesContents:1 piece

Item N° y1101 Servo horn mounting screws, 10 pcsReplacement screws for mounting the servo horn on the servo shaft.Part is delivered in silver or black color from vendor!Choises:y1101/01Fit:Multiplex Jumbo and Power MCFG 6598 Savöx-Servo SC-0251MGFG 6599 Savöx-Servo SC-1256TG Measures: M3 x 8 mmy1101/02Fit:Multiplex RhinoHitec 805 MGHitec 9805 MGFutaba S3152 Measures: M2,5 x 10 mm Torxy1101/03Fit:Futaba und Robbe diverse ServosPlease check the required dimensions! Measures: M2,5 x 6 mm Torxy1101/04Fit:402115 Mega Power-Servo, metal gears Measures: M3 x 10 mm y1101/05Fit:Ace DS1015 Super Torque Digital Servo, y1051 Measures: M3 x 10 mm