VOLZ-Servo, y1060 - 1pce. -Special offer-

Genuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece

The 2WD-465 Sportsline model is built on the short chassis with double a-arms suspension front and rear. The vehicle is equippedwith the 2-shocks front suspension as standard, which ensures optimum traction for both front wheels.On the GT2, the front axle has been widened to 384 mm. The rear axle is 395 mm wide.Technical description:The model has a 465 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads! The car comes with an unpainted body shell.The FG 5164 decor sheet is not included!Also available painted in the shop selection!Dimensions: Length: 840 mm Width: 395 mm Height: 250 mm Wheelbase: 465 mm Touring cars in action!Painting tips:

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

Highlights News 2025 Tuning aluminium lower wishbones, one-piece (front and rear) Tuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment  Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibre Highlights Formel 1 Competition- This model is fitted with numerous aluminium parts: - front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Technical description of the FG Formula 1 Competition :The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with tuning bowden cable brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition CNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ Zenoah engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, mechanical Tuning brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engineAirboxPipe Clear bodyshell and polycarbonate spoiler Mechanical brakesDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!

Competition-OnRoad RC car with the latest technical developments. Unique among the large scale models. New stabilizer bar construction front and rear. Ball stabiliszers or frame stabilizers can be used (accessories). 10 mm thick chassis made of T7075 aluminium with cut-outs for weights (also under the tank) and grooves in the front area. This allows the vehicle to be perfectly adapted to the track or the driver. The engine is now again bolted to the chassis for more stiffness. Optimally designed wishbones on front and rear suspension. Reinforced and with toe-in adjustability, which is performed via aluminum wedges. Front upper wishbone for more adjustment possibilities. All gears with fine pitch.Since 1997, i.e. since the beginning of the 1:5 RC car scene, FG Modellsport has been represented with team drivers worldwide at national and international competitions. With the Competition-EVO series, FG won most world championships and almost all European championships. Content Top suspension with 10 mm T7075 aluminum chassis plate Zenoah G230RC Engine Adjustable Tuning Clutch Air filter / Airbox Tuned pipe system Front and rear hydraulic brakes Differential Large volume shock absorbers, black anodized Wheels and rims

Specifically made to fit the Losi 5ive-T battery box. Soft case with reinforcement plates at the top and bottom and padding at the ends.Typical featuresLow inner resistance with high MPVHigher energy density with lower weightLonger lifecycle under proper usage, up to 200 timesFor LiPo batteries, the peak amp rate is usually twice the continuous crateRecommended charge with 1CSpezification:Tension: 2S / 7,4VCapacity mAh: 5200Case: SoftCable cross section: 12AWG/3,3Length +/- 5 mm: 105 mmWidth +/- 1,5 mm: 60 mmHeight: +/- 1,5 mm: 23 mmWeight +/- 10g: 208 mmCont. current: 5C (26A)Connectors: Universal and EC3, XH-balancer. Battery color may vary!Contents:1 piece