Product information "y2006 Top Tuning Digital pro servo 40 kg"
y2006 Top Tuning Digital pro 40 kg is a digital large scale servo with a very robust metal gears. It offers a lot of power at good speed and has a metal housing with side cooling fins.
Its installation dimensions fit directly for FG, Losi, HPI and various other models!
Dimensions identical to:
Multiplex Rhino - Servo 32 kg
FG Mega - Servo ST2605 30 kg
Spectrum SPMS904WP 34 kg
Spectrum SPMS904HV 18 kg
Technical data:
Classification: large scale servo
Dimensions LxWxH (mm): 59.5 x 29.2 x 55.2 mm
Operating voltage: 6 volts / 7.4 volts
Torque: (Ncm): 380/400
Speed (sec / 60 °): 0.20 / 0.18
Number of ball bearings: 2
Servo gear: metal gears
Seals: 3 (splash-protected)
Silicone cable: with universal plug, 300 mm long
Weight: 146 grams
Brass output shaft 17T spline
Content:
1 piece of TopTuning Digital pro servo 40 kg
1 piece double sided servo arm 70 mm total
1 piece of 40 mm single sided servo arm
4 pieces of guide sleeves
4 pieces of rubber grommets
4 pieces of fastening screws
0 of 0 reviews
Leave a review!
Share your experiences with other customers.
Login
No reviews found. Share your insights with others.
CYS S0650, a digital large scale servo with very robust steel gears. It offers a lot of power at good speed. Its a direct fit for cars like Losi 5ive and DBXL, UFRC Growler GX1, FG and so on.Technical data: Operating voltage: 6V-7.4V Operating speed (6.0 V): 0.13 s / 60 degrees Operating speed (7.4 V): 0.11 s / 60 degrees Holding torque (6.0V): 470 Ncm holding torque (7.4V): 539 Ncm Cable: Universal/JR connector, approx. 300mm Gear material: 1st stage brass, all others steel Bearing: 2 x ball bearing Size: 66 x 30 x 56mm Weight: 204 grams Double sided servo arm 68mm length Guide sleeve 4 pieces Mounting screws 4 pieces Mounting screws for servoarm 1 piecesContents:1 piece
The RHINO pro SHV digi 4 servo is a 29 mm digital servo designed for use in large-scale models. The new pro SHV servo is faster, more powerful, and more durable than the proven RHINO digi 4, of which thousands are now in use. More performance, with higher torque and faster transit speed, and more durable with a new triple-ballraced heavy-duty steel gear set. The operating voltage range has been expanded to 7.4 V, allowing the servo to be operated directly with up to two-cell LiPo batteries.Large 1 : 5 scale model cars make very exacting demands on the servos, and for many years the RHINO servo has set the standard with its extremely robust, outsize metal gearbox and 8 mm output shaft for the output device. An integral aluminium heat-sink cools the motor and electronics very effectively. Servo case gaskets make the unit dust-proof and splash-proof. The enormous power and robust nature of this servo also make it an excellent choice for large models generally, such as F3A - XXL large-scale model aircraft, as well as for non-standard applications.Adapter FG # 6118/02 is required for installation into a FG/Smartech car.High-voltage (HV) servosHV servos have a broad operating voltage range of 5 - 7.4 V, i.e. they can be operated directly with two-cell Lithium-based rechargeable batteries (e.g. LiPo, LiFe, LiIo). The outstanding features of LiXX batteries compared with NiXX types are their higher energy density and lower self-discharge rate, and for these reasons they are increasingly used as power supplies in model RC systems. The higher voltage of LiXX batteries means that the current drawn by an HV servo is lower for a given output power than that of conventional servos, which are generally designed for a nominal voltage of 4.8 - 6 V. When used with 2S LiXX batteries, these older servos must therefore be operated with a separate voltage reducer. This reduces the overall efficiency of the system, leads to unnecessary dissipated power, requires additional electronic complexity and more connectors ( higher costs, greater failure risk, higher weight). Modern receivers (e.g. M-LINK) are designed for voltages up to 9 V, i.e. with HV there is no longer any reason not to use the modern, superior LiXX battery technology.The following servo parameters can be adjusted using the MULTImate test and programming unit # 8 2094:Direction of servo rotationServo transit speedServo travel, left / right (max. 2 x 90°)Servo centreServo deadbandFail-safe (On with servo Fail-Safe position / Off)Reset to factory default settingsSpecificationDimensions (L x W x H):Weight::Gearbox:Ballraces:Multi-finger wiper pot:Torque @ 6 V / 7f.4 V*:Holding power @ 6 V / 7.4 V*:Transit speed for 40°@ 6 V / 7.4 V*: 59 x 29 x 55 mm172 gSteel3yes (with indirect drive)230 / 270 Ncm280 / 320 Ncm** 0,10 / 0,08 sec.* 5-cell NiXX / 2S LiPo operation. Values measured at stabilised 6.0 V / 7.4 V.** Holding power at angular error
The brushless Big Scale servo is an extremely robust digital servo, with a high performance brushless motor, in absolute premium quality, with a full aluminum case for optimal heat dissipation in the 2-version with elaborate cooling fins, metal gears and equipped with high-quality 30 cm long silicone insulated cable. Where with other high-performance servos you still have to buy an aluminum top or case as third party options, the brushless Big Scale servo already comes with a full metal case, and above all, the aluminum to features special bushings for the intermediate shafts! Of course, the support from a metal top cover guarantees a much longer service life of the complete gearbox, than with a plastic version! Defective gears are known to be the most frequent cause of failure; especially for highly stressed servos in 1/5 and 1/6 cars! The brushless Big Scale servo is also the first choice for 1/8 and 1/10 race cars, where fast reaction times and high steering forces bring up the demand for an extremely fast and reliable servo! Also, servo mounting tab breakage on the servo cover is virtually impossible with the brushless Big Scale servo. Dimensions:Length: 40 mmWidth: 20 mmHeight: 41.4 mmWeight: 72 gramsPerformance:7.4 V6 VHolding torque kg-cm/oz-in30.0/41726,0/361Speed sec./60°0.110.14Accessories included:Three different plastic servo horns / discFour each rubber grommets and guide sleevesMounting screwsNote: Due to the extreme holding power of the brushless Big Scale servo the rubber grommets should always be installed in combination with the guide sleeves. The brushless Big Scale servo comes with accessories in a high quality plastic case with molded insert.We recommend an aluminum servo arm from the selection of the article:Alloy servoarms, for 25 teeth multi-tooth shaft 9,90 EUR
The brushless Big Scale servo is an extremely robust digital servo, with a high performance brushless motor, in absolute premium quality, with a full aluminum case for optimal heat dissipation in the 2-version with elaborate cooling fins, metal gears and equipped with high-quality 30 cm long silicone insulated cable. Where with other high-performance servos you still have to buy an aluminum top or case as third party options, the brushless Big Scale servo already comes with a full metal case, and above all, the aluminum to features special bushings for the intermediate shafts! Of course, the support from a metal top cover guarantees a much longer service life of the complete gearbox, than with a plastic version! Defective gears are known to be the most frequent cause of failure; especially for highly stressed servos in 1/5 and 1/6 cars! The brushless Big Scale servo is also the first choice for 1/8 and 1/10 race cars, where fast reaction times and high steering forces bring up the demand for an extremely fast and reliable servo! Also, servo mounting tab breakage on the servo cover is virtually impossible with the brushless Big Scale servo. Dimensions:Length: 40 mmWidth: 20 mmHeight: 41.4 mmWeight: 72 gramsPerformance:7.4 V6 VHolding torque kg-cm/oz-in30.0/41726,0/361Speed sec./60°0.110.14Accessories included:Three different plastic servo horns / discFour each rubber grommets and guide sleevesMounting screwsNote: Due to the extreme holding power of the brushless Big Scale servo the rubber grommets should always be installed in combination with the guide sleeves. The brushless Big Scale servo comes with accessories in a high quality plastic case with molded insert.We recommend an aluminum servo arm from the selection of the article:Alloy servoarms, for 25 teeth multi-tooth shaft 9,90 EUR
Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all, necessary for installation, accessories (see also our pictures)One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline and E (in connection with alloy front uprights y0932Dimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set
Genuine HT spare/option part. The Y-harness is required for running two servos on a single receiver channel. Top quality heavy gauge 0.5 mm² cable with silicone insulation, 150 mm long, suitable for all rc-systems.Content:1 piece
Item N° y0700 Double sided alloy servoarm, 1 pce.Suitable for all servos with an output shaft with 25 teeth multi-tooth shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!When you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.
The brushless Big Scale servo is an extremely robust digital servo, with a high performance brushless motor, in absolute premium quality, with a full aluminum case for optimal heat dissipation in the 2-version with elaborate cooling fins, metal gears and equipped with high-quality 30 cm long silicone insulated cable. Where with other high-performance servos you still have to buy an aluminum top or case as third party options, the brushless Big Scale servo already comes with a full metal case, and above all, the aluminum to features special bushings for the intermediate shafts! Of course, the support from a metal top cover guarantees a much longer service life of the complete gearbox, than with a plastic version! Defective gears are known to be the most frequent cause of failure; especially for highly stressed servos in 1/5 and 1/6 cars! The brushless Big Scale servo is also the first choice for 1/8 and 1/10 race cars, where fast reaction times and high steering forces bring up the demand for an extremely fast and reliable servo! Also, servo mounting tab breakage on the servo cover is virtually impossible with the brushless Big Scale servo. Dimensions:Length: 40 mmWidth: 20 mmHeight: 41.4 mmWeight: 72 gramsPerformance:7.4 V6 VHolding torque kg-cm/oz-in30.0/41726,0/361Speed sec./60°0.110.14Accessories included:Three different plastic servo horns / discFour each rubber grommets and guide sleevesMounting screwsNote: Due to the extreme holding power of the brushless Big Scale servo the rubber grommets should always be installed in combination with the guide sleeves. The brushless Big Scale servo comes with accessories in a high quality plastic case with molded insert.We recommend an aluminum servo arm from the selection of the article:Alloy servoarms, for 25 teeth multi-tooth shaft 9,90 EUR
Item N° y0700/01 Single-sided alloy servoarm, 1 pce.Suitable for all servos with an output shaft with 25 teeth multi-tooth shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!When you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.
€8.90*
This website uses cookies to ensure the best experience possible. More information...