y0735 Safety clip for Universal / JR / Futaba connectors
Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece
y0113/01 Thread locking compound,medium
Genuine HT spare/option part.Available as 272 high strength and heat resistant, 270/1 high strength or 241 medium strength.The strength of 272 and 270/1 is comparable, but 272 can handle temperatures up to 230°C vs. 150°C for 270/1. It is therefore the perfect choice for applications like exhaust or clutch pinion bolts. However, curing of 272 takes at least twice as long as 270/1.An excellent recommendation for removal of screws treated with threadlocking compound:CFH Diamant M50 Gasbrenner, y1007 Contents:1 piece / 10 gram
Content: 20 Gramm (€395.00 / 1000 Gramm)
TT0198 Top Tuning Bubble-Ex for 1/10 up to 1/5 scale rc-cars
Genuine Top Tuning spare/option part. Indispensable for optimal suspension tuning!Vacuum container for removal of bubbles from shock fluid when filling shocks.A vacuum pump is built into the lid. The tray has four holes each to accept 1/10, 1/8, 1/6 and 1/5 scale shocks.Suitable for shock absorbers from Losi, Mecatech, BWS, Arrma, Traxxas, FG, Carson, HPI and many more, as long as they have a suitable diameter. All shocks from 15 to 32 mm outer diameter can be used in the Bubble Ex to be "de-bubbled". Tray bore sizes: No. 1 = 32 mm diameter No. 2 = 21 mm diameter No. 3 = 17.5 mm diameter No. 4 = 15 mm diameter The maximum length of the shock absorber up to the upper edge of the body is about 150 mm, whereby longer shock absorbers can also be partially compressed for insertion. (e.g Losi 5ive-T and many more)Operation:Unlock the vacuum pump by turning it slightly to the left, the pump handle then extends a little. The small plug with handle is used to close and ventilate the container. To build up the vacuum, the plug must be in the down position.The small membrane on the opposite side serves as an indicator for whether a vacuum is present. Only when this is curved outwards the lid of the container can be opened again without any effort. Content: Can with integrated vacuum pump Shock tray
y1388 Offroad tuning springs Dirt-Spring DBXL/XL-E +MTXL
Genuine HT spare/option part. Fits Losi Desert Buggy XL stock shocks.The Desert Buggy XL stock springs use a high preload, which is even bigger than the shocks travel. This means that the stock spring action increases not that much going through the available suspension travel. To handle hard impacts high viscosity oil is used in the shocks; however, this oil is too heavy for these springs for a proper rebound. A sensible suspension tuning becomes much pretty difficult.For this reason, the tuning springs Dirt-Spring Desert Buggy XL are shorter than the stock springs, but also use heavier gauge wire in return. Therefore the change in spring action during the suspension travel is noticeably higher than the preload; the suspension settings can be influenced more effectively.Due to their different characteristics the stock springs are difficult to be sorted among the line of the tuning springs.As a rule of thumb theyre similar to the 2.7 mm version when used with the current 2000 viscosity oil factory fill.Dimensions:Inner diameter: 35 mmFree length: 110 mmNumber of turns: 9Versions:y1388/01 - 2,5 x 110 mm Ochery1388/02 - 2,6 x 110 mm Bluey1388/03 - 2,7 x 110 mm Greeny1388/04 - 2,8 x 110 mm Silvery1388/05 - 2,9 x 110 mm Whitey1388/06 - 3,0 x 110 mm Goldy1388/08 - Complete set, unit prices: 132,93 EUR
y0720 rc-car-online Transmitter bag
Genuine HT spare/option part. Extremely sturdy, fully padded transmitter bag! Fits all popular pistol grip transmitters Top quality; with padded adjustable length retaining straps to secure the transmitter, large zippered flap and adjustable carrying strap. Dimensions: Width: 23 cmHeight: 34 cmDepth: 17 cmContents:1 piece
y0113/02 Thread locking compound, high strength
Genuine HT spare/option part.Available as 272 high strength and heat resistant, 270/1 high strength or 241 medium strength.The strength of 272 and 270/1 is comparable, but 272 can handle temperatures up to 230°C vs. 150°C for 270/1. It is therefore the perfect choice for applications like exhaust or clutch pinion bolts. However, curing of 272 takes at least twice as long as 270/1.An excellent recommendation for removal of screws treated with threadlocking compound:CFH Diamant M50 Gasbrenner, y1007 Contents:1 piece / 10 gram
Content: 20 Gramm (€495.00 / 1000 Gramm)
AT-DBXL001 ATOP Alloy spring retainer for Losi DBXL/XL-E +MTXL shocks
Genuine Atop spare/option part. Two pieces CNC-machined 6061-T6 aluminum spring perches for Losi DBXL. Direct replacement for the stock part (from set. # LOS 253006).Content:2 pieces
y0039 Oil for shock absorber, all viscosities, 100 ml
Genuine silicone shock absorber oil for the optimal shock absorber set-up. Content: 100 ml Please note: Factory filling of FG/Losi/Smartech and many other 1/5 and 1/6 scale shocks is done with genuine silicone shock absorber oil. To ensure seal tightness and consistency you should only use genuine silicone shock absorber oil for refilling as well.Most every rc-car shock absorber uses silicone oil of different viscosities. The smaller the number, the lower the viscosity of the silicone oil and the softer the damping. As a rule of thumb: Viscosity 100 = similar to water Viscosity 1.000 = similar to cooking oil Viscosity 5.000 = similar to shampoo Viscosity 10.000 = similar to honey As a reference: The red FG Marder / Off-Road Buggy series shock absorbers are factory filled with 2.000 viscosity oil, the shocks on monster cars with dual shock set-ups (total of 8 shocks) are filled with 1.000 viscosity oil, and the shocks on FG onroad cars come filled with 4.000 viscosity oil. The original filling of the Losi 5ive-T is 350cc silicone oil.FG Silicone oil with 100 ml:FG Item N° 66295/010 = Viscosity: 100 FG Item N° 66295/025 = Viscosity: 250FG Item N° 66295/035 = Viscosity: 350FG Item N° 66295/050 = Viscosity: 500FG Item N° 66295/075 = Viscosity: 750FG Item N° 66295/100 = Viscosity: 1000FG Item N° 66295/150 = Viscosity: 1500FG Item N° 66295/200 = Viscosity: 2000FG Item N° 66295/300 = Viscosity: 3000FG Item N° 66295/400 = Viscosity: 4000FG Item N° 66295/500 = Viscosity: 5000FG Item N° 66295/600 = Viscosity: 6000FG Item N° 66295/700 = Viscosity: 7000FG Item N° 66295/800 = Viscosity: 8000FG Item N° 66295/900 = Viscosity: 9000FG Item N° 66296 = Viscosity: 10000Viscosity of silicone oil at various temperatures.
Content: 100 Milliliter (€154.00 / 1000 Milliliter)
y0744 Differential Silicone oil / grease, viscosity 15.000 untill 2.000.000, 50 ml
For changing the locking effect of large scale car differentials.Top quality in 50 ml plastic wide-neck bottles.Silicone oil / grease with a viscosity to choose:15.00030.00050.000100.000300.0001.000.0002.000.000Viscosity of silicone oil at various temperatures.
Content: 50 Milliliter (€298.00 / 1000 Milliliter)
y1309 All steel linkage for steering servo/servo saver application
Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
AT-DBXL028 ATOP Aluminum rear uprights for all Losi DBXL/MTXL
Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum rear uprights from ATOP to fit all Losi DBXL and MTXL versions, gasoline and electric.Significantly more rigid than the stock plastic version, this part contributes to increased directional stability. Plastic bushings for the hinge pins ensure reduced wear.Two additional mounting points are available for attaching the camber rods, allowing the model's handling to be better matched to the track.Comes with wheel bearings included. Contents:2 pieces
AT-DBXL003 ATOP aluminum throttle/brake servo horn for Losi DBXL/DBXL-E
Genuine ATOP spare/option part. CNC-machined from 6061 aluminum, significantly stronger and more rigid than any plastic version. Doule-sided anodized aluminum servo horn, available in 15T and 18t spline version. Three smooth 2.5 mm holes per side. 15T fits:Savöx 0236 MGSavöx 0235Losi 900and many other servos with 15T spline shaft18T fits:Spektrum DBXL-servo SPMS901Contents:1 piece
y1418 Heavy duty bead lock rings for MadMax rims
Can be used as reinforcement for genuine HPI and Losi rims as well.Set includes:Two pieces of reinforced outside ringsTwo pieces of reinforced inside ringsand 40 pieces of 3 mm allen head screws (for 2,5 mm allen wrench)Colours:y1418/02 - Bluey1418/03 - Redy1418/05 - Yellow
TT1000 Top Tuning Electronic 20 Amp Bigscale high voltage 30 Volt switch
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
AT-DBXL026/027 ATOP Aluminum front spindles for all Losi DBXL/MTXL
Genuine ATOP spare/option part. One-piece CNC machined 6061-T6 aluminum spindles from ATOP, fits all Losi DBXL and MTXL versions, gas and brushless.Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Stainless steel bushings for the King Pins are included.Comes with wheel bearings included. Contents:2 pieces
LOS45007 Beadlock Set, Inner & Outer fluorescent orange 5T
Genuine Losi spare/option part.The set is for two tires (one pair).Content:1 set
y1320 Narrow-Grip 616 type drift tires, mounted and with 24 mm hex for Losi, HPI, MCD
The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs. - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.
y0688 HT RTR set with 2.4 GHz remote control for all FG and Carson 1:6 scale models
This set contains:Top Digital Big-Scale Steering ServoTop Digital Big-Scal Throttle/brake servo 7573 FG Radio controll 2,4 GHz incl. receiverT1257 FG Universal Chargery0425 Y-harness, universal connector2000 mAh 6V Battery with universal connectorWhen used in a FG 2WD car, adaptor plate 6118/02 is required for steering servo installation.
y0057 Ball & socket tool for Losi and HPI
Genuine HT spare/option part. Ball & socket tool with t-handle, special version for the ball joints.Fits Losi 5ive-T. 5ive-B, Desert Buggy XL, Desert Buggy XL-E, Monster Truck XL and the HPI Baja 5B and Baja 5R Ford Mustang.Contents:1 piece
AT-DBXL002/01 ATOP Spacer bushings for camber/steering rods of Losi DBXL and DBXL-E
Genuine ATOP spare/option part. Aluminum spacer bushings for the ball joints on camber and steering rods of Losi DBXL and DBXL-E.Content:8 pieces
HURRAX extreme Race tires + GRP Disc rim 24 mm hex + inlays set
You can select the tyre hardness above: - Hurrax HX100 extreme Grip Medium 175/70 mm tyre and - Hurrax HX400 extreme Grip Soft 175/70 mm tyre Please select which tyre you prefer. You also have the option of having the tyres delivered ready glued for an additional charge. Please click if you want to have the tyres ready glued! HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms
y1321 Molded tire inserts for 170 mm Ø MadMax tires with 60 + 80 mm width
Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the MadMax tires with 170 / 190 mm tire diameter is available in two widths.Fits 10-spoke GPM-racing aluminum rims (Losi / HPI). Applications:for 60 mm tire width: # y1321/01for 80 mm tire width: # y1321/02for GIANT-GRIP #y1321/06
AT-DBXL022 ATOP Aluminum rear transmission mount for Losi DBXL/DBXL-E/2.0 + MTXL
Genuine ATOP spare/option part. Rear transmission mount for Losi DBXL cnc-machined from 6061 aluminum by ATOP.Through the use of aluminum, the problem of torn out threads (incl. the front bumper installation) is eliminated. At the same time the chassis section under the transmission is strengthened and the mounting points for the shock towers are reinforced.Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!
AT-DBXL021 ATOP Aluminum front transmission mount for Losi DBXL/DBXL-E/2.0 + MTXL
Genuine ATOP spare/option part. Front transmission mount for Losi DBXL cnc-machined from 6061 aluminum by ATOP.Through the use of aluminum, the problem of torn out threads (incl. the front bumper installation) is eliminated. At the same time the chassis section under the transmission is strengthened and the mounting points for the shock towers are reinforced.Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!