AT-DBXL025 ATOP aluminum front top chassis brace for Losi DBXL-E 2.0
€34.90
Available
Product information "AT-DBXL025 ATOP aluminum front top chassis brace for Losi DBXL-E 2.0"
CNC-machined 6061-T6 aluminum front top chassis brace; fits Losi DBXL-E 2.0 only.
Stiffer than the stock plastic part (from set # LOS251097), the aluminum brace reduces chassis tweak in the area of the steering assy.
Contents:
- 1 piece
Login
Customers also bought
Genuine ATOP spare/option part. Camber rods for Losi DBXL with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Fits front and rear.Attention: On a DBXL-E 2.0 these rods can only be used as camber rods, not as steering rods! Dimensions: Hole to hole: 117mm Total length: 135mm Contents:2 pieces
Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP. CNC-machined 6061-T6 aluminum servo clamps from Area RC distribute the load from the mounting screws equally over the complete area of the mounting tabs, protecting them against breakage. Available in two versions:AT-5T020-01 - 0236 for stock servos in Losi 5ive and DBXL, Savöx 235 und 236, Orange Power and other servos with a mounting hole distance of 18 mmAT-5T020-02 - 5765 for MPX Rhino, Hitec 5765 and other servos with a mounting hole distance of 16 mmContents:2 pieces
Genuine HT spare/option part. This machined aluminum servo adapter allows easy installation of servos with a 69 x 18 mm mounting bolt pattern (for example Orange-Power, S8203) in vehicles / radio plates which provide a 75 x 18 mm mounting bolt pattern (for example Losi 5ive-T, Mini WRC, HPI Baja 5 series cars, many FG cars).The use of this adapter servo will neither tilt the servo, nor does it change installation height. Scope of delivery:1 x Servo mount adapter2 x Socket head cap screws 3 x 20 mm2 x Socket head cap screws 3 x 12 mm2 x Shim ring 3,2 mmContents:1 piece
Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum rear uprights from ATOP to fit all Losi DBXL and MTXL versions, gasoline and electric.Significantly more rigid than the stock plastic version, this part contributes to increased directional stability. Plastic bushings for the hinge pins ensure reduced wear.Two additional mounting points are available for attaching the camber rods, allowing the model's handling to be better matched to the track.Comes with wheel bearings included. Contents:2 pieces
Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum front chassis brace for Losi DBXL-E 2.0.Compared to the stock plastic part (from set # LOS251100) the higher strength of the aluminum part noticeably increases the chassis rigidity.Contents:1 piece
Customers also viewed
The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder is also available with completely installed remote control. Just fuel up, start the engine and drive off.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Features:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm
Genuine ATOP spare/option part. Set of 3!Two-part differential housing made of aluminum with steel bearing shield. The one-piece steel end shield ensures greater stability compared to aluminum end shields with a pressed-in bushing.Fits all differentials in all DBXL and DBXL-E 2.0 versions!The delivery includes gaskets and O-rings, screws, ball bearing and sliding blocks.Contents:3 pieces
Genuine Atop spare/option part. Two pieces CNC-machined 6061-T6 aluminum spring perches for Losi DBXL. Direct replacement for the stock part (from set. # LOS 253006).Content:2 pieces
Genuine ATOP spare/option part. Steering rods for Losi DBXL-E 2.0 with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Dimensions: Hole to hole: 108mm Total length: 128mm Contents:2 pieces
Genuine Losi spare/option part. Contents:6 pieces
Genuine Losi spare/option part. Contents:1 piece
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum rear chassis brace 1 + 2 for Losi DBXL-E 2.0.Compared to the stock plastic part (from set # LOS251100) the higher strength of the aluminum part noticeably increases the chassis rigidity.Contents:1 set