AT-DBXL028 ATOP Aluminum rear uprights for all Losi DBXL/MTXL
€79.90
Available
Product information "AT-DBXL028 ATOP Aluminum rear uprights for all Losi DBXL/MTXL"
CNC machined 6061-T6 aluminum rear uprights from ATOP to fit all Losi DBXL and MTXL versions, gasoline and electric.
Significantly more rigid than the stock plastic version, this part contributes to increased directional stability. Plastic bushings for the hinge pins ensure reduced wear.
Two additional mounting points are available for attaching the camber rods, allowing the model's handling to be better matched to the track.
Comes with wheel bearings included.
Contents:
- 2 pieces
Login
Customers also bought
Genuine ATOP spare/option part. One-piece CNC machined 6061-T6 aluminum spindles from ATOP, fits all Losi DBXL and MTXL versions, gas and brushless.Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Stainless steel bushings for the King Pins are included.Comes with wheel bearings included. Contents:2 pieces
Genuine Atop spare/option part. Two pieces CNC-machined 6061-T6 aluminum spring perches for Losi DBXL. Direct replacement for the stock part (from set. # LOS 253006).Content:2 pieces
Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum front chassis brace for Losi DBXL-E 2.0.Compared to the stock plastic part (from set # LOS251100) the higher strength of the aluminum part noticeably increases the chassis rigidity.Contents:1 piece
Customers also viewed
Original Zenoah 32 cm³ Rebuilt kit Top quality with Zenoah warranty!Set includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipThrust washer for needle bearingCover for transfer portAttention: For the assembling of the covers enclosed please use the HT-flange sealer y804 and pay attention to the assembling instructions enclosed.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Genuine ATOP spare/option part. One-piece CNC machined 6061-T6 aluminum spindles from ATOP, fits all Losi DBXL and MTXL versions, gas and brushless.Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Stainless steel bushings for the King Pins are included.Comes with wheel bearings included. Contents:2 pieces
Genuine ATOP spare/option part. CNC-machined from 6061-T6 aluminum by ATOP. Open design for maximum clutch cooling and reduced weight. Larger 15x32x9 mm bearings for higher load capacity.Contents:1 piece
Genuine Area spare/option part.CNC-machined from 6061-T6 aluminum by Area RC for Losi 5ive-T/B and Mini tank. Does not fit the tank from a 2.0. Even though the part number of the tank did not change, thread diameter on the 2.0 tank is a few tenths of a millimeter larger.Contents:1 piece
Genuine Losi spare/option part. Contents:6 pieces
Genuine Losi spare/option part. Contents:4 pieces