TT0198 Top Tuning Bubble-Ex for 1/10 up to 1/5 scale rc-cars
€69.90
Available
Product information "TT0198 Top Tuning Bubble-Ex for 1/10 up to 1/5 scale rc-cars"
Indispensable for optimal suspension tuning!
Vacuum container for removal of bubbles from shock fluid when filling shocks.
A vacuum pump is built into the lid. The tray has four holes each to accept 1/10, 1/8, 1/6 and 1/5 scale shocks.
Suitable for shock absorbers from Losi, Mecatech, BWS, Arrma, Traxxas, FG, Carson, HPI and many more, as long as they have a suitable diameter. All shocks from 15 to 32 mm outer diameter can be used in the Bubble Ex to be "de-bubbled".
Tray bore sizes:
- No. 1 = 32 mm diameter
- No. 2 = 21 mm diameter
- No. 3 = 17.5 mm diameter
- No. 4 = 15 mm diameter
The maximum length of the shock absorber up to the upper edge of the body is about 150 mm, whereby longer shock absorbers can also be partially compressed for insertion. (e.g Losi 5ive-T and many more)
Operation:
Unlock the vacuum pump by turning it slightly to the left, the pump handle then extends a little. The small plug with handle is used to close and ventilate the container. To build up the vacuum, the plug must be in the down position.
The small membrane on the opposite side serves as an indicator for whether a vacuum is present. Only when this is curved outwards the lid of the container can be opened again without any effort.
Content:
- Can with integrated vacuum pump
- Shock tray
Login
Accessories / Spare parts
Genuine silicone shock absorber oil for the optimal shock absorber set-up. Content: 50 ml Please note: Factory filling of FG/Losi/Smartech and many other 1/5 and 1/6 scale shocks is done with genuine silicone shock absorber oil. To ensure seal tightness and consistency you should only use genuine silicone shock absorber oil for refilling as well.Most every rc-car shock absorber uses silicone oil of different viscosities. The smaller the number, the lower the viscosity of the silicone oil and the softer the damping. As a rule of thumb: Viscosity 100 = similar to water Viscosity 1.000 = similar to cooking oil Viscosity 5.000 = similar to shampoo Viscosity 10.000 = similar to honey As a reference: The red FG Marder / Off-Road Buggy series shock absorbers are factory filled with 2.000 viscosity oil, the shocks on monster cars with dual shock set-ups (total of 8 shocks) are filled with 1.000 viscosity oil, and the shocks on FG onroad cars come filled with 4.000 viscosity oil. The original filling of the Losi 5ive-T is 350cc silicone oil.FG Silicone oil with 50 ml:FG Item N° 6510/010 = Viscosity: 100FG Item N° 6510/025 = Viscosity: 250FG Item N° 6510/035 = Viscosity: 350FG Item N° 6510/050 = Viscosity: 500FG Item N° 6510/075 = Viscosity: 750FG Item N° 6510/100 = Viscosity: 1000FG Item N° 6510/150 = Viscosity: 1500FG Item N° 6510/200 = Viscosity: 2000FG Item N° 6510/300 = Viscosity: 3000FG Item N° 6510/400 = Viscosity: 4000FG Item N° 6510/500 = Viscosity: 5000FG Item N° 6510/600 = Viscosity: 6000FG Item N° 6510/700 = Viscosity: 7000FG Item N° 6510/800 = Viscosity: 8000FG Item N° 6510/900 = Viscosity: 9000FG Item N° 6511 = Viscosity: 10000Viscosity of silicone oil at various temperatures.
Content: 50 Milliliter (€179.00 / 1000 Milliliter)
Genuine silicone shock absorber oil for the optimal shock absorber set-up. Content: 100 ml Please note: Factory filling of FG/Losi/Smartech and many other 1/5 and 1/6 scale shocks is done with genuine silicone shock absorber oil. To ensure seal tightness and consistency you should only use genuine silicone shock absorber oil for refilling as well.Most every rc-car shock absorber uses silicone oil of different viscosities. The smaller the number, the lower the viscosity of the silicone oil and the softer the damping. As a rule of thumb: Viscosity 100 = similar to water Viscosity 1.000 = similar to cooking oil Viscosity 5.000 = similar to shampoo Viscosity 10.000 = similar to honey As a reference: The red FG Marder / Off-Road Buggy series shock absorbers are factory filled with 2.000 viscosity oil, the shocks on monster cars with dual shock set-ups (total of 8 shocks) are filled with 1.000 viscosity oil, and the shocks on FG onroad cars come filled with 4.000 viscosity oil. The original filling of the Losi 5ive-T is 350cc silicone oil.FG Silicone oil with 100 ml:FG Item N° 66295/010 = Viscosity: 100 FG Item N° 66295/025 = Viscosity: 250FG Item N° 66295/035 = Viscosity: 350FG Item N° 66295/050 = Viscosity: 500FG Item N° 66295/075 = Viscosity: 750FG Item N° 66295/100 = Viscosity: 1000FG Item N° 66295/150 = Viscosity: 1500FG Item N° 66295/200 = Viscosity: 2000FG Item N° 66295/300 = Viscosity: 3000FG Item N° 66295/400 = Viscosity: 4000FG Item N° 66295/500 = Viscosity: 5000FG Item N° 66295/600 = Viscosity: 6000FG Item N° 66295/700 = Viscosity: 7000FG Item N° 66295/800 = Viscosity: 8000FG Item N° 66295/900 = Viscosity: 9000FG Item N° 66296 = Viscosity: 10000Viscosity of silicone oil at various temperatures.
Content: 100 Milliliter (€154.00 / 1000 Milliliter)
For changing the locking effect of large scale car differentials.Top quality in 50 ml plastic wide-neck bottles.Silicone oil / grease with a viscosity to choose:15.00030.00050.000100.000300.0001.000.0002.000.000Viscosity of silicone oil at various temperatures.
Content: 50 Milliliter (€298.00 / 1000 Milliliter)
Customers also bought
Even though the blade will keep its edge for a long time, no cutting tool will last forever. Spare blades are available of course.Cutting width approx. 3 mmPack of 5
Genuine HT spare/option part. After-Run is a performance enhancing preservation, which ensures that the engine starts properly, even after a long time (winter break) storage. Added to the fuel it keeps the fuel system clean.Among other After-Run conserves the diaphragm of the Walbro carburetor!For long term storage (i.e. during winter!) "vital" for the carburetor diaphragms!For 23 to 32 cm³ engines like Zenoah, Chung Yang, PT, Losi, HPI a.s.o.It binds water in the fuel, particularly important when the engine is not run regularly or after wet races. After-Run improves engine performance, ensures better combustion, removes debris and residues. Simply add the content of the bottle to 5 litres of fuel.Contents:1 piece / 20 ml
Content: 20 Milliliter (€495.00 / 1000 Milliliter)
Fully synthetic oil, available in three blends. 1-liter bottle.The optimal 2-stroke oil for 23-30 cm³ engines/cars Motul Racing Oil is available in three different blends: On-Road for high revving onroad cars Off-Road for cars with high torque enginesMixing ratio for 1/5 & 1/6 applications: We recommend a mix with about 4% oil, which means 200 cc of oil to 5 litres of gas (1:25 ratio). With one litre of Motul oil you can mix about 25 litres of optimal fuel for your 1/5 or 1/6 car. That's enough for well over 20 hours of driving fun! Oil / Gas Oil percent Oil per 1 liter of gasoline Oil per 2 liter of gasoline Oil per 3 liter of gasoline Oil per 4 liter of gasoline Oil per 5 liter of gasoline 1:20 5% 50 ml 100 ml 150 ml 200 ml 250 ml 1:25 4% 40 ml 80 ml 120 ml 160 ml 200 ml 1:30 3,33% 33 ml 67 ml 100 ml 134 ml 167 ml 1:33 3% 30 ml 60 ml 90 ml 120 ml 150 ml 1:35 2,86% 29 ml 58 ml 86 ml 115 ml 143 ml 1:40 2,5% 25 ml 50 ml 75 ml 100 ml 125 ml 1:50 2% 20 ml 40 ml 60 ml 80 ml 100 ml
Genuine Motul spare/option part. High-cling oil for foam cartridge air filters, especially for offroad and street use. The oil reinforces the the air filter'e efficiency and retains dirt, mud and sand particles, which will greatly extend the life of the engine. The blue tint makes it easier to control even oil application to the filter.Apply oil to filter generously and work the foam vigorously by hand to ensure complete oil penetration. Press foam slightly to remove excessive oil when done.Contents:1 piece / 400 ml
Content: 400 Milliliter (€47.25 / 1000 Milliliter)
Hazard and Precautionary StatementsLabelling according to Regulation (EC) No. 1272/2008 [CLP] Signal word (CLP) : Danger Hazardous ingredients : Hydrocarbons, C9-C11, n-alkanes, isoalkanes, cyclic compounds, <2% aromatic compounds Hazard statements (CLP): H222 - Extremely flammable aerosol. H229 - Pressurised container: May burst if heated. H319 - Causes serious eye irritation. H336 - May cause drowsiness or dizziness. Safety instructions (CLP): P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P211 - Do not spray on an open flame or other ignition source. P251 - Do not pierce or burn, even after use. P260 - Do not breathe aerosol. P271 - Use only outdoors or in well-ventilated areas. P280 - Wear protective gloves and eye protection. P304+P340 - IF INHALED: Remove person to fresh air and keep comfortable for breathing. P305+P351+P338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P312 - Call a POISON CENTRE or doctor/physician if you feel unwell. P331 - Do NOT induce vomiting. P403+P233 - Store in a well-ventilated place. Keep container tightly closed. P337+P313 - If eye irritation persists: Get medical advice/attention. P410+P412 - Protect from sunlight and do not expose to temperatures exceeding 50 °C/122 °F. EUH statements: EUH066 - Repeated exposure may cause skin dryness or cracking. Seal and Bond Remover is a slow evaporating universal degreaser that is also perfect for quickly and efficiently removing all types of adhesive and sealant residue. The product softens most adhesives and sealants to make them easier to remove.Seal and Bond Remover is suitable for all types of metals and most plastics. In addition, it can be used without risk on almost all modern paints. This makes it particularly suitable for removing stickers, emblems, bumper trims and any adhesive residue that may remain. Even traces of sealant and adhesive after dismantling brackets, etc. can be safely removed without damaging the substrate. Seal and Bond Remover is also ideal for making surfaces free of grease and silicone, for example before applying new stickers, emblems, etc.Due to its high dissolving power, Seal and Bond Remover is also a recommended solution for removing tar splashes or even rubber from trim, etc.In the spray can, Seal and Bond Remover is particularly user-friendly and practical to use. Thanks to the unbreakable nozzle with spray tube, even hard-to-reach places are easy to reach. In addition, the spray can has a special valve that allows it to be used in any position. This allows emblems and bumper strips, among other things, to be removed most effectively by spraying Seal and Bond Remover directly behind the part in question while slowly pulling it off. HIGHLIGHTS. Very easy to use. Ideal for removing adhesive, tar, sealant and chewing gum residues Significantly facilitates the cutting out of glued car windows. Does not attack paint or most plastics in any way OEM approved CONTENT Base: Mixture of aliphatic and aromatic hydrocarbons. Density: 762 kg/m³ Consistency: liquid (ready to spray in aerosol can) Viscosity: ± 2 mPa.s Solvent: mixture of aliphatic and aromatic hydrocarbons. Flash point: 0°C Evaporation residue: None, the product dries without residue. Processing conditions: +10°C to +40°C Substrate: The most common substrates. If necessary, test in an inconspicuous place. USAGE.Shake spray can well before use. Spray Seal and Bond Remover on the surface to be treated and allow to act briefly. Remove adhesive, tar, sealant, chewing gum residues with a Multi Wipe. Wipe off with a clean, dry cloth or Multi Wipe. For thicker layers, remove the top layer first and then repeat the treatment. Hand cleaning: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water Shelf life: 2 years in unopened original packaging Storage conditions: Store in a cool, dry place Batch code type: F Details: OEM approval
Content: 500 Milliliter (€39.80 / 1000 Milliliter)
Genuine HT spare/option part. Milled to reduce weight; replaces plastic part FG #66287/01. Comes complete with all necessary mounting hardware included.Fits Leopard Sportsline 2WD and 4WD.Scope of delivery:1x Alloy front shock tower4x Socket head cap screws 4x143x Countersunk screws 4x144x Washers steel 4,3Contents:1 piece
Customers also viewed
Wheelie bar with double ball raced wheel, cnc-machined from high strength alloy. The arm has a rubber suspension unit, the height is infinitely adjustable. The suspension allows for a maximum deflection of 30 degrees and is dirt- and mud-proof. The wheel bearings are sealed.The unit fits FG Monster Truck, Monster Beetle and Marder BigFoot, except for Monster Buggy Off-Road WB535 4WD. Installation on other models will be possible, but requires modifications to the chassis, mainly to accept the bolt pattern. The Carson Attack already has the correct pattern.
Tools and decorative items are for presentation purpose only and not included. Genuine HT spare/option part. Tool bag, extremely rugged tool bag made from reinforced fabric, sewn edge. With 41 flexible attachment loops for various tools with all-round zipper and reinforced handle.Dimensions:Width: 510 mm Height: 275 mmContents:1 piece
The tire tread cutter is required for re-cutting worn-out or creating new tread designs in order to get more grip. Cutting depth is adjustable and cutting width is approx. 3 mm.Please note: This tool is designed for cutting model tires only, not for any fullsize vehicle tires!Content:1 pieces
Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey, Super Baja Rey 2.0 and Super Rock Rey. Suitable for 8 mm axles.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: These adapters only fit in combination with the optional aluminum spindles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which requires different dimensions for the wheel drives.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fenderwells will need some cutting. Please note: the wide rear wheels from MadMax or HPI do not fit! This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm
6 litre gas can with thumb activated filler valve.With Rapido filling up is quicker, simpler and more convenient than ever! Thanks to the dosing button you can control the flow of fuel precisely.Unlock by folding out!Press the button and keep control of filling!Lock by folding in again. Finished!No spills, no awkward handling, all clean and easy Other:Half round spout for ventilation and visibility suitable also for the smallest tank openingsLarge opening for easy fillingFlow controlled by press-buttonVentilation allows full flowSturdy design with two handlesTransparent 6 litre container with litre indication in the filling and rest positionsContents:1 piece
The safety fuel filling system is perfect for refueling all common fuel tanks and fits all common jerry cans up to 5 liters. The integrated ventilation of the fueling system allows a gurgling-free pouring. In addition, the automatic filling stop prevents fuel overflow and spillage.The environmentally friendly filling system reduces the escape of fuel vapors during and after refueling and thus protects against contamination. A union nut is included for exact positioning of the system at small tank openings. In addition, the filler is equipped with a retaining loop so that it can be securely attached to the jerry can.Safety Fuel Filling Systemno overflow and spillageThe automatic filling stop prevents overflow and spillage.Gurgling-free refuelingThanks to the integrated ventilation, gurgling-free refueling is possible at last and the escape of environmentally harmful fuel vapors is reduced.Integrated lid attachmentThe integrated lid fastening prevents loss, which is especially useful for mobile use.Lid lockingNo more losing the cap. Lid lock is directly connected to the can.VentilationGurgling-free refueling. Reduction of escape of environmentally harmful fuel vapors.Made in GermanyThe filling system is manufactured in Germany. Overview: Safety nozzle filling system for fuel With integrated ventilation for refueling without gurgling Reduction of escape of environmentally harmful fuel vapors Integrated automatic filling stop to prevent overflow and spillage With union nut for exact positioning of the system With captive screw connection Practical strap for attachment to the jerry can included Made in Germany Filling opening: ø inside = 29 mm, thread outside ø = 38 mm Nozzle: ø outside = 21 mm, length = 160 mm Material: Polyethylene (HD-PE) Color: black/red Content:1 x Safety fuel filling system
Genuine FG spare/option part.Stock tuning pipe for all 1/5 scale cars and Trucks models with engine in horizontal position. Now in noise-limited three-chamber version.Contents:1 piece