LOS252120 Losi Axle Boot Set 5mm Drive Pins DBXL-E 2.0
€29.99
Available
Product information "LOS252120 Losi Axle Boot Set 5mm Drive Pins DBXL-E 2.0"
Contents:
- 10 pieces
Login
Customers also bought
Genuine Losi spare/option part. Contents:1 set
Complete set of 22 sealed ball bearings for Losi DBXL-E 2.0 and Desert Buggy XL 1/5.Set includes:16 pieces of 12 x 24 x 6 mm sealed bearings (axle shafts / differentials / clutch bell)4 pieces of 10 x 22 x 6 sealed bearings (bevel pinion shafts)2 pieces of 8 x 19 x 6 sealed bearings (intermediate shaft)Total: 22 sealed bearingsPrice when bought separately: 95.92 EUR
Genuine Top Tuning spare/option part. Motor adapter plate to mount the ZTW 620KV Beast motor into the Losi DBXL-E 2.0. The plate has four mounting holes, which should also be used due to the enormous torque of the ZTW motor. In order to install the screw at the l/h top position, at least 0.6mm material must be removed from the existing motor/differential mount. Contents:1 piece
Genuine Losi spare/option part. The esc mounting bracket is equipped with an extremely strong double-sided adhesive tape for fixing the controller. Additionally the esc can be secured with the Top Tuning Velcro TT1021/12, which you can select from the shopping options.Compared to the standard plate, the support surface has been widened by 1mm, so that the ZTW 300A controller can be mounted ideally; slipping back and forth is securely avoided.Contents:1 set
Genuine Losi spare/option part. Contents:1 piece
Genuine HT spare/option part. Fits Losi Desert Buggy XL stock shocks.The Desert Buggy XL stock springs use a high preload, which is even bigger than the shocks travel. This means that the stock spring action increases not that much going through the available suspension travel. To handle hard impacts high viscosity oil is used in the shocks; however, this oil is too heavy for these springs for a proper rebound. A sensible suspension tuning becomes much pretty difficult.For this reason, the tuning springs Dirt-Spring Desert Buggy XL are shorter than the stock springs, but also use heavier gauge wire in return. Therefore the change in spring action during the suspension travel is noticeably higher than the preload; the suspension settings can be influenced more effectively.Due to their different characteristics the stock springs are difficult to be sorted among the line of the tuning springs.As a rule of thumb theyre similar to the 2.7 mm version when used with the current 2000 viscosity oil factory fill.Dimensions:Inner diameter: 35 mmFree length: 110 mmNumber of turns: 9Versions:y1388/01 - 2,5 x 110 mm Ochery1388/02 - 2,6 x 110 mm Bluey1388/03 - 2,7 x 110 mm Greeny1388/04 - 2,8 x 110 mm Silvery1388/05 - 2,9 x 110 mm Whitey1388/06 - 3,0 x 110 mm Goldy1388/08 - Complete set, unit prices: 132,93 EUR
Customers also viewed
Complete tuned pipe system, will be delivered as shown with manifold, hose with clamps and variable mount. Fits FG and Carson touring cars / GTs with long wheel base.The tuned pipe is for a 535 wheelbase. The diameter is 51 mm and the complete length is about 300 mm.
Genuine Losi spare/option part. Contents:10 pieces
Genuine Losi spare/option part. Contents:1 set
To ensure the required cooling for current 1/5 and 1/6 engines the flywheels have fins on both sides. Therefore the fan housing has large openings on the crankcase side for the required air supply. However, the risk of foreign objects (grass, sand, or even stones!) entering here Is very high! As a result, broken fins on the flywheel occur frequently. This leads to reduced cooling efficiency and - even more critical vibrations from a flywheel which is out of balance due to missing fins. Therefore, this kind of flywheel protection is highly recommended, especially for offroad use. The product video explains the handling in detail! Note:It is essential to thoroughly clean and degrease the crankcase prior to attaching the hook-and-loop tape (OKS2661)!For installation on Chung-Yang and Zenoah engines in FG cars, the crankcase cover must be slightly modified in two places where the engine mount is attached (see Figure 6 and 7). Furthermore the fit of the fabric must be as tight as possible in the region of the layshaft pinion (in front of the differential ring gear!) (see Figure 8).Set includes:Special tailored fabric with sewed on hook-and-loop tapehook-and-loop tape for installation to the crankcaseAdhesive for securing the hook-and-loop tape
Genuine silicone shock absorber oil for the optimal shock absorber set-up. Content: 50 ml Please note: Factory filling of FG/Losi/Smartech and many other 1/5 and 1/6 scale shocks is done with genuine silicone shock absorber oil. To ensure seal tightness and consistency you should only use genuine silicone shock absorber oil for refilling as well.Most every rc-car shock absorber uses silicone oil of different viscosities. The smaller the number, the lower the viscosity of the silicone oil and the softer the damping. As a rule of thumb: Viscosity 100 = similar to water Viscosity 1.000 = similar to cooking oil Viscosity 5.000 = similar to shampoo Viscosity 10.000 = similar to honey As a reference: The red FG Marder / Off-Road Buggy series shock absorbers are factory filled with 2.000 viscosity oil, the shocks on monster cars with dual shock set-ups (total of 8 shocks) are filled with 1.000 viscosity oil, and the shocks on FG onroad cars come filled with 4.000 viscosity oil. The original filling of the Losi 5ive-T is 350cc silicone oil.FG Silicone oil with 50 ml:FG Item N° 6510/010 = Viscosity: 100FG Item N° 6510/025 = Viscosity: 250FG Item N° 6510/035 = Viscosity: 350FG Item N° 6510/050 = Viscosity: 500FG Item N° 6510/075 = Viscosity: 750FG Item N° 6510/100 = Viscosity: 1000FG Item N° 6510/150 = Viscosity: 1500FG Item N° 6510/200 = Viscosity: 2000FG Item N° 6510/300 = Viscosity: 3000FG Item N° 6510/400 = Viscosity: 4000FG Item N° 6510/500 = Viscosity: 5000FG Item N° 6510/600 = Viscosity: 6000FG Item N° 6510/700 = Viscosity: 7000FG Item N° 6510/800 = Viscosity: 8000FG Item N° 6510/900 = Viscosity: 9000FG Item N° 6511 = Viscosity: 10000Viscosity of silicone oil at various temperatures.
Content: 50 Milliliter (€179.00 / 1000 Milliliter)
Genuine ATOP spare/option part. Camber rods for Losi DBXL with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Fits front and rear.Attention: On a DBXL-E 2.0 these rods can only be used as camber rods, not as steering rods! Dimensions: Hole to hole: 117mm Total length: 135mm Contents:2 pieces
Genuine Losi spare/option part. Contents:1 set