LOS252017 Axle Boot Set Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³. incl. clutch spring!Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!

Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 piece

Genuine HT spare/option part. Fits Losi Desert Buggy XL stock shocks.The Desert Buggy XL stock springs use a high preload, which is even bigger than the shocks travel. This means that the stock spring action increases not that much going through the available suspension travel. To handle hard impacts high viscosity oil is used in the shocks; however, this oil is too heavy for these springs for a proper rebound. A sensible suspension tuning becomes much pretty difficult.For this reason, the tuning springs Dirt-Spring Desert Buggy XL are shorter than the stock springs, but also use heavier gauge wire in return. Therefore the change in spring action during the suspension travel is noticeably higher than the preload; the suspension settings can be influenced more effectively.Due to their different characteristics the stock springs are difficult to be sorted among the line of the tuning springs.As a rule of thumb theyre similar to the 2.7 mm version when used with the current 2000 viscosity oil factory fill.Dimensions:Inner diameter: 35 mmFree length: 110 mmNumber of turns: 9Versions:y1388/01 - 2,5 x 110 mm Ochery1388/02 - 2,6 x 110 mm Bluey1388/03 - 2,7 x 110 mm Greeny1388/04 - 2,8 x 110 mm Silvery1388/05 - 2,9 x 110 mm Whitey1388/06 - 3,0 x 110 mm Goldy1388/08 - Complete set, unit prices: 132,93 EUR 

Genuine Losi spare/option part. Contents:2 pieces