LOS252125 Losi Universal Rebuild Kit, 4,6mm Pin, DBXL-E 2.0

€9.99*

Prices incl. VAT plus shipping costs

Available

Product number: losi_los252125

EAN: 605482493366

Product information "LOS252125 Losi Universal Rebuild Kit, 4,6mm Pin, DBXL-E 2.0"

Genuine Losi spare/option part.

Contents:

2 pieces

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

7041 FG Plastic bush for brake caliper

Genuine FG spare/option part. Fits calipers 7040 and 7040/1.Dimensions:Inner diameter: 6,15 mmOuter diameter: 8 mmWidth: 5,8 mmFlange thickness: 1,1 mmContent:4 pieces

€3.50*

y1409/01 GIANT GRIP tires on MadMax Extreme rims for Losi and HPI, pair

GIANT GRIP 190 x 70 with black colored MadMax Extreme rims, 20-fold screwed, very tough, with 24 mm hex drive and reinforced orange beadlock rings for Losi 5ive-T and Desert-Buggy XL as well as all HPI Baja 5 B/T cars.The GIANT GRIP provides giant traction through 96 about one cm² wide and 5 mm high strong lugs, getting ample grip even on loose surfaces like sand and soil.Due to the extreme strain caused by the GIANT GRIP tires the MadMax rim with reinforcement ring had to be optimized once more.The GIANT GRIP tires come with strong special tire inserts which allow to transfer the power without canting, even on heavy cars like the Losi 5ive-T.Dimensions:Outer diameter: 190 mmTire width at bead 70 mmTread width 80 mmReinforced 24 mm hex wheel driveThe MadMax Giant Grip tires use 60 mm wide rims ( y1415/01 or y0761/01).The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

From €64.90*

Details

y1419/01 Clutch spring 6.000 1 / min for the Sintered clutch for Zenoah, Chung Yang, Losi, HPI & Co.

Clutch spring for about 6,000 1 / min. for the OEM clutches from Zenoah and many other rc-car engines from 23 cm³ - 32 cm³.Content:1 piece

€5.90*

6427 FG Plastic gear wheel 46 teeth - 1pce.

46 teeth gear wheel for the layshaft.Diameter 72 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

7423 FG Plastic gear carrier 47mm - 1pce.

Suitable for .

€11.90*

Similar products

LOS252067 Losi Diff Rebuild Kit, Al Diff Housing, DBXL-E

Genuine Losi spare/option part. Contents:1 set

€29.99*

Details

LOS252120 Losi Axle Boot Set 5mm Drive Pins DBXL-E 2.0

Genuine Losi spare/option part. Contents:10 pieces

€29.99*

LOS254006 Losi Suspension Arm Set Losi DBXL/DBXL-E/DBXL 2.0 1/5 4WD

Genuine Losi spare/option part. Content:4 pieces

€59.99*

LOS254010 Losi Hinge Pin, Set Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€19.99*

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*