LOS252061 Losi Center Diff Spur Gear, 48T, DBXL-E

€49.99*

Prices incl. VAT plus shipping costs

Available

Product number: losi_los252061

EAN: 605482086766

Product information "LOS252061 Losi Center Diff Spur Gear, 48T, DBXL-E"

Genuine Losi spare/option part.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

LOS254006/01 Suspension Arm Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Content:1 piece

€16.90*

LOS252120 Losi Axle Boot Set 5mm Drive Pins DBXL-E 2.0

Genuine Losi spare/option part. Contents:10 pieces

€29.99*

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*

LOS254005 Losi Uprights Carriers/Spindles/Hubs Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€39.99*

LOS254009 Losi Hinge Pin Brace Inserts, Set Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€9.99*

LOS254006 Losi Suspension Arm Set Losi DBXL/DBXL-E/DBXL 2.0 1/5 4WD

Genuine Losi spare/option part. Content:4 pieces

€59.99*

LOS252127 Losi Diff Shims, 24x21x0.3mm, DBXL-E 2.0

Genuine Losi spare/option part. Contents:10 pieces

€9.99*

LOS252064 Losi Pinion Gear, 13T, 1.5M, 8 mm Shaft

Genuine Losi spare/option part. Contents:1 piece

€19.99*

LOS252125 Losi Universal Rebuild Kit, 4,6mm Pin, DBXL-E 2.0

Genuine Losi spare/option part. Contents:2 pieces

€9.99*

Details

Losi LOS250044 Body Set, Screened, DBXL-E 2.0

Genuine Losi spare/option part. Contents:1 set

€159.99*

LOS351018 Losi Front Top Plate, Aluminum, Black, DBXL-E 2.0

Genuine Losi spare/option part. Contents:1 piece

€39.99*

Details

LOS252065 Losi Pinion Gear, 14T, 1.5M, 8 mm Shaft

Genuine Losi spare/option part. Contents:1 piece

€19.99*

Customers also viewed

TT1021/07 Top Tuning electric Motor pinion nitrided hardened, 8 mm bore, module 1.5

Genuine Top Tuning spare/option part. Motor pinion made of nitrided hardened steel, module 1.5 and 8 mm bore. Reinforced hub for set screw M5x6. The pinions with odd tooth counts are profile shifted. Within the same outer diameter, there is no need to adjust the backlash when changing the pinion. When mounting on vehicles with mounting holes in the motor mount that are specific to the tooth count, the mounting holes for the higher number of teeth in each case (16 or 18) must be used.Profile regraded:This means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter. Available in two sizes with two tooth counts:Outer diameter 30 mm with 17T or 18TOuter diameter 27 mm with 15T or 16TContents:1 piece

€23.90*

Details

y0039 Oil for shock absorber, all viscosities, 100 ml

Genuine silicone shock absorber oil for the optimal shock absorber set-up. Content: 100 ml Please note: Factory filling of FG/Losi/Smartech and many other 1/5 and 1/6 scale shocks is done with genuine silicone shock absorber oil. To ensure seal tightness and consistency you should only use genuine silicone shock absorber oil for refilling as well.Most every rc-car shock absorber uses silicone oil of different viscosities. The smaller the number, the lower the viscosity of the silicone oil and the softer the damping. As a rule of thumb: Viscosity 100 = similar to water Viscosity 1.000 = similar to cooking oil Viscosity 5.000 = similar to shampoo Viscosity 10.000 = similar to honey As a reference: The red FG Marder / Off-Road Buggy series shock absorbers are factory filled with 2.000 viscosity oil, the shocks on monster cars with dual shock set-ups (total of 8 shocks) are filled with 1.000 viscosity oil, and the shocks on FG onroad cars come filled with 4.000 viscosity oil. The original filling of the Losi 5ive-T is 350cc silicone oil.FG Silicone oil with 100 ml:FG Item N° 66295/010 = Viscosity: 100 FG Item N° 66295/025 = Viscosity: 250FG Item N° 66295/035 = Viscosity: 350FG Item N° 66295/050 = Viscosity: 500FG Item N° 66295/075 = Viscosity: 750FG Item N° 66295/100 = Viscosity: 1000FG Item N° 66295/150 = Viscosity: 1500FG Item N° 66295/200 = Viscosity: 2000FG Item N° 66295/300 = Viscosity: 3000FG Item N° 66295/400 = Viscosity: 4000FG Item N° 66295/500 = Viscosity: 5000FG Item N° 66295/600 = Viscosity: 6000FG Item N° 66295/700 = Viscosity: 7000FG Item N° 66295/800 = Viscosity: 8000FG Item N° 66295/900 = Viscosity: 9000FG Item N° 66296 = Viscosity: 10000Viscosity of silicone oil at various temperatures.

Content: 100 Milliliter (€129.00* / 1000 Milliliter)

From €12.90* €15.40* (16.23% saved)

Details

LOS252125 Losi Universal Rebuild Kit, 4,6mm Pin, DBXL-E 2.0

Genuine Losi spare/option part. Contents:2 pieces

€9.99*

Details

TT1028 Top Tuning High-performance fan 60 x 60 x 24 mm

Genuine Top Tuningspare/option part. High performance fan as upgrade for various applications in electric models.The size 60 x 60 x 24 mm can be swapped e.g. for the fan of the ZTW Beast 300A speed controller. For this particular application, M4x40 screws are required instead of the standard M4x30 screws due to the 9 mm taller fan.The air flow is considerably higher than with the standard units!The operating voltage of the fan with 5 - 8.4 V is perfectly adapted to these requirements. Technical data: Dimensions: 60 x 60 x 24 mm Operating voltage: 5 8.4 V Current: 0.5A Speed: 8,500 rpm @ 8.4 V Air flow: 39.2 cfm Connector: BEC female Cable length: approx. 30 cm Contents:1 piece

€19.90*