Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

LOS252134 Losi Center Driveshaft, Front: DBXL 2.0

Product information "LOS252134 Losi Center Driveshaft, Front: DBXL 2.0"

Genuine Losi spare/option part.

Contents:
  • 1 piece


0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

Average rating of 0 out of 5 stars

LOS252135 Losi Center Driveshaft, rear: DBXL 2.0
Genuine Losi spare/option part. Contents:1 piece

€39.99*

Average rating of 0 out of 5 stars

AT-DBXL028 ATOP Aluminum rear uprights for all Losi DBXL/MTXL
Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum rear uprights from ATOP to fit all Losi DBXL and MTXL versions, gasoline and electric.Significantly more rigid than the stock plastic version, this part contributes to increased directional stability. Plastic bushings for the hinge pins ensure reduced wear.Two additional mounting points are available for attaching the camber rods, allowing the model's handling to be better matched to the track.Comes with wheel bearings included. Contents:2 pieces

€79.90*

Average rating of 0 out of 5 stars

AT-DBXL026/027 ATOP Aluminum front spindles for all Losi DBXL/MTXL
Genuine ATOP spare/option part. One-piece CNC machined 6061-T6 aluminum spindles from ATOP, fits all Losi DBXL and MTXL versions, gas and brushless.Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Stainless steel bushings for the King Pins are included.Comes with wheel bearings included. Contents:2 pieces

€149.90*

Similar products

Average rating of 0 out of 5 stars

LOS252017 Axle Boot Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:10 pieces

€29.99*

Average rating of 0 out of 5 stars

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL
Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*

Average rating of 0 out of 5 stars

LOS252009 Differential Rebuild Kit Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€8.99*

Average rating of 0 out of 5 stars

LOS252006 Front/Rear Differential Outdrive Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:2 pieces

€29.99*

Average rating of 0 out of 5 stars

LOS252018 Front Universal Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 piece

€59.99*

Average rating of 0 out of 5 stars

LOS252135 Losi Center Driveshaft, rear: DBXL 2.0
Genuine Losi spare/option part. Contents:1 piece

€39.99*

Average rating of 0 out of 5 stars

LOS252010 Differential Case Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€29.99*

Average rating of 0 out of 5 stars

LOS252016 20T Pinion Gear Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 piece

€19.99*

Average rating of 0 out of 5 stars

LOS252019 Front Center Driveshaft Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 piece

€59.99*

Average rating of 0 out of 5 stars

LOS252008 FR/R 43T Ring and 13T Pinion Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€69.99*

Average rating of 0 out of 5 stars

LOS252002 Center Dog Bone, short Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. 

€39.99*

Average rating of 0 out of 5 stars

LOS252001 Driveshaft & Axle Dogbone Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:2 pieces

€39.99*

Customers also viewed

Average rating of 0 out of 5 stars

LOS252119 Losi Front CVD Assembly, 5mm Pin for DBXL-E 2.0
Genuine Losi spare/option part. Contents:1 piece

€49.99*

Average rating of 0 out of 5 stars

LOS251096 Losi Turnbuckle Set for DBXL-E 2.0
Genuine Losi spare/option part. Contents:6 pieces

€59.99*

Average rating of 0 out of 5 stars

LOS252010 Differential Case Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€29.99*

Average rating of 0 out of 5 stars

LOS05020V2/BEAST Losi DBXL-E 2.0 4WD 12S Brushless RTR
Unfortunately the Fox body is no longer available! Beast Edition: Standard equipment: Beast Edition: Motor: 780kV 650/620kV Regler: 160 A 250/300A S-Power:   8S     12S The Losi DBXL-E 2.0 is fitted with a Spektrum 780KV motor and a 160A Spektrum ESC as standard.With our 12S Beast Edition you can choose between 2 variants:1.  Hobbywing Ezrun Max5 HV ESC 250A up to 12S LiPo BEC8 and Ezrun 650KV 4pol brushless motor, without surcharge.2.  Hobbywing Ezrun Max4 HV ESC Sensorless 300A up to 12S LiPo, BEC 10A and Top Tuning Beast Brushless Motor 620KV 4pol, 190,00 € extra charge.                 The original DBXL-E set the world on fire as the go-to vehicle for large scale bashers and enthusiasts alike. Its agile handling, out of the box speeds and durability make it a fan favorite. Now the Losi® DBXL-E 2.0 continues to build on the legendary status! Known worldwide for their dominance in the gas 1/5 market, especially with the 5IVE-T 2.0, Losi has built the DBXL-E 2.0 to be cleaner and easier to use, but with performance and speed that outruns the competition. At home in any environment from dirt to pavement, wet or dry, especially with its 4WD drivetrain with larger 5mm drive pins, the desert buggy makes sure all the power is put to the ground. Drivers stay in control with a DX3 transmitter, a Spektrum SR6100AT 6 Channel AVC® Telemetry Surface Receiver, and scale-to-size Maxxis Creepy Crawler LT tires. This desert buggy features all the technological advances drivers. Finally, the DBXL-E 2.0 has a Losi race-inspired motorsports themed livery for that true off-road look. You get all this and more from the brand that represents the pinnacle of performance.The Full-Throttle Freedom of AVC® TechnologyThe receiver's built-in AVC® (Active Vehicle Control®) traction control system works behind the scenes, making hundreds of throttle and steering adjustments per second, so more of the motor's power is translated into ballistic speed and acceleration instead of just flying dirt. The patent-pending AVC system adds a level of performance that simply cannot be found with any vehicle from any manufacturer other than Horizon Hobby. Like traction control in your full-scale vehicle, you can activate or deactivate the system on the fly and adjust the level of stability based on driving conditions. Any RC vehicle can go fast and with AVC you can go faster while maintaining optimum stability in all driving conditionFeatures Without surcharge : Ezrun MAX5 HV G2 ESC 12S and Ezrun 650KV brushless engine. Surcharge 190€ : Ezrun MAX4 HV G2 ESC and Top Tuning BEAST 620KV Brushless engine. Spektrum DX3 radio system with AVC® and new SR6100AT Receiver Spektrum S906 1/5th scale metal gear servo Water protected components Aluminum Shock Towers Aluminum Center Diff Cup New Radio Tray designed for use with single or dual steering servos. New Heavy Duty Drivetrain with 5mm drive pins New Electric Chassis specific chassis braces for increased durability and strength Spedial motor adapter plate Modified ESC mounting bracket Beast decal sheet New ESC Mount Pinned Center Outdrive Cups New Gearboxes for improved drivetrain strength and stability New Steering Rack with helical servo saver design Updated Front and Rear Bulkheads Maxxis Creepy Crawler LT Tires Losi and Fox Shox race-inspired Motorsports themed livery Laser Etched FOX Logo Shock Caps Roof-mounted LED bar Dimensions Height: 317 mm Length: 844 mm Width: 495 mm Weight: 9,8 kg

€1,599.00*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency