LOS254005 Losi Uprights Carriers/Spindles/Hubs Losi DBXL+MTXL 1/5 4WD
€39.99
Currently unavailable
Product information "LOS254005 Losi Uprights Carriers/Spindles/Hubs Losi DBXL+MTXL 1/5 4WD"
Contents:
- 1 set
Login
Accessories / Spare parts
Genuine Losi spare/option part. Contents:1 set
Alternatives
Genuine ATOP spare/option part. One-piece CNC machined 6061-T6 aluminum spindles from ATOP, fits all Losi DBXL and MTXL versions, gas and brushless. Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Stainless steel bushings for the King Pins are included.Comes with wheel bearings included. Contents:2 pieces
Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum C-hubs from ATOP to fit all Losi DBXL and MTXL versions, gas and brushless.Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Plastic bushings for the hinge pins ensure reduced wear. Contents:2 pieces
Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum rear uprights from ATOP to fit all Losi DBXL and MTXL versions, gasoline and electric.Significantly more rigid than the stock plastic version, this part contributes to increased directional stability. Plastic bushings for the hinge pins ensure reduced wear.Two additional mounting points are available for attaching the camber rods, allowing the model's handling to be better matched to the track.Comes with wheel bearings included. Contents:2 pieces
Genuine Losi spare/option part. Contents:1 set
Customers also bought
Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set
Genuine Losi spare/option part. Contents:10 pieces
Genuine Losi spare/option part. Content:4 pieces
Genuine Losi spare/option part. Contents:1 set
Genuine Losi spare/option part. Contents:4 pieces
Customers also viewed
Genuine ATOP spare/option part. One-piece CNC machined 6061-T6 aluminum spindles from ATOP, fits all Losi DBXL and MTXL versions, gas and brushless. Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Stainless steel bushings for the King Pins are included.Comes with wheel bearings included. Contents:2 pieces
Genuine Losi spare/option part. Contents:1 set
Genuine FG spare/option part. Suitable for all FG 2WD 1:6 Off-Road and monster models.Bearing seats: 22 x 7 mm.Contents:1 set
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum front chassis brace for Losi DBXL-E 2.0.Compared to the stock plastic part (from set # LOS251100) the higher strength of the aluminum part noticeably increases the chassis rigidity.Contents:1 piece
Genuine Losi spare/option part. Contents:1 piece
Genuine ARRMA spare/option part. Tires: Multi-surface chunky tread pattern for awesome traction in all conditions - High-quality rubber for long-lasting durability - Pre-glued for trouble-free fit and servicingWheels: Multi-spoke design for stylish looks and increased strength - Tough nylon for durability on all surfaces - Black color for head-turning ARRMA styling - Steel reinforced 24mm Hex for strength during extreme driving action and easy servicingFoam Inserts: High-quality foam with excellent support for the tire tread - Specially designed to give the perfect balance of aggressive grip and easy handling characteristicsTECHNICAL INFORMATION: Wheel bead diameter: 4.9" (124mm) Width: 3.98" (101mm) Wheel hex size: 24mm Overall diameter: 8" (203mm) Contents:1 pair / 2 pieces