LOS252051 Losi Wheel Nut, Black MTXL

€19.99*

Prices incl. VAT plus shipping costs

Available

Product number: losi_los252051

EAN: 605482624975

Product information "LOS252051 Losi Wheel Nut, Black MTXL"

Genuine Losi spare/option part.

Contents:

4 pieces

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

LOS251120 Losi Throttle Linkage Set: DBXL 2.0

Genuine Losi spare/option part. Contents:1 set

€29.99*

Details

LOSB5972 Losi Outer Axle Ball Bearings sealed, 12 x 24 x 6 mm, Losi 5ive-T/2.0, TLR 5ive-B and Mini WRC.

Fits Losi 5ive-T, TLR 5ive-B and Mini WRC.Dimensionally identical with B59010 / B59011.Content:2 pieces

€9.99*

LOS251021 Mount/Guard, Engine, Set Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€39.99*

LOS251114 Losi Radio Tray Set: DBXL 2.0

Genuine Losi spare/option part. Contents:1 set

€29.99*

Details

LOS252050 Losi Wheel Hex Black with Pin MTXL

Genuine Losi spare/option part.Contents:4 pieces

€39.99*

LOS252116 Losi Rear Stub Axle, 5mm Pin for DBXL-E 2.0

Genuine Losi spare/option part. Contents:2 pieces

€39.99*

Similar products

LOS252120 Losi Axle Boot Set 5mm Drive Pins DBXL-E 2.0

Genuine Losi spare/option part. Contents:10 pieces

€29.99*

LOS252067 Losi Diff Rebuild Kit, Al Diff Housing, DBXL-E

Genuine Losi spare/option part. Contents:1 set

€29.99*

LOS254006/01 Suspension Arm Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Content:1 piece

€16.90*

LOS254010 Losi Hinge Pin, Set Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€19.99*

LOS254005 Losi Uprights Carriers/Spindles/Hubs Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€39.99*

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*