99 products found for "montage_0001"

Catalogue #1

y0109 Universal radio plate for FG 1/6 2WD

Genuine HT spare/option part. Universal radio plate for FG 2WD Marder/Beetle/Off-Road Buggy/Pajero an all Monster and Stadium models. With drilling templates for the following steering servos:Hitec HS-805BB/HS-5745/5735/Orange Power MPX Jumbo und Rhino The size of the steering servo can vary because you can adjust the position of the aluminum tray bar to accomodate larger or smaller servos. You will need FG adapters for installation of the gas / brake servo: #5014/04 servo mounting frame for (standard sized) Futaba / JR, Thunder Tiger DS1015 - 2pcs. Accepts FG servo frames for up to two throttle/brake servos (not included). Spacers for rx-box installation are included.Old version chassis plates (~pre 2003) have a different bolt pattern. When installing this radio plate on an old chassis new mounting holes must be drilled into the chassis plateThe surface is plain aluminum. With the necessary effort it can be polished to a high luster.Contents:1 piece

€99.90*

y0112 Universal radio plate On-Road

Universal radio plate, accepts the same servos as described under, but with a layout to fit FG Leopard and all onroad cars except EVO4 and Formula 1.You will need FG mounting frames for installation of the brake/thottle servo(s), the frames are not included.With drilling templates for the following steering servos:Hitec HS-805BB/HS-5745/5735/Orange PowerMPX Jumbo und RhinoThe surface is plain aluminum. With the necessary effort it can be polished to a high luster.

€79.90*

Adaptor blocks for carbon RC-plate, y19005/01 - 1pce.

Alloy adaptor blocks for the RC-plate above.When you use MPX Jumbos or Hitec 5735/5745 for brake throttle, these blocks will bring the servos to the correct height.

€12.30*

0304.340304.10 OSKART Brems/Gas Montagematerial

Genuine OSKART Brake/ Speed Hardware Mounting Kit spare/option part.Fits 1/2 scale OSKART.Contents:1 set

€38.00*

6000c/2023 FG Marder Vintage-Classic with 26 ccm engine RTR

With complete RTR equipment y1382 Original Maxi-Pin 1/6 offroad competition tire The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder comes with completely installed remote control. Just fuel up, start the engine and drive off.Features:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm

€849.90* €969.95* (12.38% saved)

y1569 Low voltage buzzer with voltage test

Genuine HTspare/option part. The LiPo Voltage Checker provides a low voltage alarm for 28S cell counts.When the voltage is below the set value, an alarm will sound along with illuminating the red LED.The voltage checker will automatically detect the cell count when connected to the balance lead on 28S LiPo. SpecificationsInput: 1S (JST) and 28S (JST-XH) LiPo, Li-ION/LiMN/Li-FeUnit Voltage Display Range: 0.54.5 VTotal Voltage Display Range: 0.536 VTest Mode Voltage Range: 3.730 VAlarm Value Range: 2.73.8 V, including offDimensions: 3.9 cm x 2.4 cm x 0.9 cmContents:1 piece

€9.90*

P-SBS/01V Futaba Voltage sensor

Genuine Futaba spare/option part.Voltage sensor for Futaba S.BUS2. telemetry system.Suitable for use with the Futaba 4PX, 7PX transmitter.Technical data:Range: EXT line Voltage: 0.0V ~ 100.0V / Normal line Voltage: 3.5V ~ 8.4V (It measures to the first decimal place)Length: 870mmWeight: 6.0gVoltage: DC 3.7 ~ 7.4VContents:1 piece

€59.90*

y1048 HT Aluminum-Frontaxle for FG Sportsline

Genuine FG spare/option part. Suitable for FG Sportsline (old version, not 4wheel drive basic) and Eco-Line.The set includes:Item N°.Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1209HT Aluminum front bulkhead A y1210HT Aluminum front bulkhead B y1036HT rose joints with conical spacersUnit prices: 318,30 EURPlease note: the hinge pins are not included, you will use the pins from the stock suspension!Additional parts shown on the pictures, like diskbrakes or other tuning parts, are only decoration and not part of the set. Contents:1 set

€269.00* €318.30* (15.49% saved)

Low voltage failsafe module, y0423 - 1pce.

To protect a car from a crash in case the power supply fails is no easy task. The mechanical devices that are used to do the job are either bulky or cause a higher drain from the battery. The failsafe module is a more efficient way.The module controls the battery pack's voltage and takes control of the throttle servo when the voltage goes below 4.7 volts. As an additional feature you can supply a backup battery pack to power the throttle servo in case the main pack falls completely. The failsafe position of the throttle servo is adjustable.

€49.30*

y1306 JETI-SBEC 6-42V voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

This product is currently not available.

00010100 Lightscale

€7.90*

300001318 Carson Assembly wrench

Genuine Carson spare/option part. Contents:1 piece

€19.90*

E540001 UFRC Chassis plate

Genuine UFRC spare/option part. Fits Growler GX1.Contents:1 piece

€199.00*

6547 FG Receiver cable FG gold contact/Futaba - 1pce.

Receiver cable, ready-made with FG gold contact plug-in system for Futaba plug.total length 20-25cm

€17.90*

6547/02 FG Receiver cable FG gold contact/JR-Graupner - 1pce.

Receiver cable, ready-made with FG gold contact plug-in system für JP-Graupner plug.total length 20-25cm

€17.90*

8344/01 FG Coupling flange for Solo/Zenoah horizontal 1:5 - 1pce.

Suitable for FG CY23, CY26, Zenoah G230RC, G230RC 04, G260RC, G240, G270, G290, ZG22 as well as Solo engines.

€42.80*

52050001 Lightscale rear wing complete for touring-cars

The Lightscale spoiler for touring cars is a form-blown plastic part which is hollow inside and the outside has the effective wing shape. The plastic used is extremely durable and lightweight. The lateral supports are formed of Lexan and offer the possibility to set the wing at an angle and adjust the hight. The integrated carbon wingrestraints facilitates a securely screwed wing.  The shape of the wing is optimized to bring a good downforce at minimum storage effect, thus ensuring the safe driving through fast corners without sacrificing top speed on straight sections. The total weight of the wing, including all attachments is about 60 grams and is therefore lighter then many carbon wings. The wing has already proved it's durability during crash tests, but still of course all its components are also available separately.

€59.90*

This product is currently not available.

Spektrum SPMA9570A Telemetry Pack Voltage Sensor 2 pin

Genuine Spektrum spare/option part. Contents:1 piece

€9.99*

WD-40 Contact spray

WD-40 SPECIALIST contact spray removes oil, dirt, flux and oxidation residues from sensitive electrical or electronic equipment. The product can be used on electrical equipment, contacts, plastic and rubber.Temperature application range: room temperatureApplication:First disconnect all plugs from equipment to avoid current and allow hot surfaces to cool. Shake the can before use and apply the spray directly on the surface to be treated at a distance of 15 to 20 cm. This will remove any residue that could interfere with electrical contact. Tilt the surface while cleaning and allow excess liquid to dry completely before restoring power. To avoid accidental damage, always check the manufacturer's instructions before applying the product to the equipment. Do not spray product into cavities, openings, crevices or areas of your device where it does not have sufficient airflow to support complete evaporation.Smart Straw - Product Benefits:The integrated spray head allows you to switch between large-area and precise spraying. In this case, the tube remains firmly attached to the spray head and is therefore no longer lost during application. For area spraying, the spray tube is simply folded down. With the spray tube folded out, you can reach small spaces and apply the product there with pinpoint accuracy. The 360° valve allows the can to be held upright or even overhead, making any application possible.WD-40® multifunctional product infiltrates and loosens rusted and stuck screws. It penetrates the threads of hinges and protects against corrosion. WD-40® multifunction product displaces moisture, lubricates and eliminates squeaks. > PRODUCT PERFORMANCE AND FEATURES: Smart Straw® Spray system for area and spot spraying Fast acting and non-conductive Perfect cleaning for electrical/electronic equipment, contacts, plastics or rubber Penetrates quickly without leaving residues Penetrates even the most difficult to reach areas K2 registered #145372 > AREAS OF APPLICATION: Electrical assembly Circuit boards Controls Printers & copiers Switches > USAGE: Shut off unit and allow hot surfaces to cool. Disconnect all plugs from unit to avoid power supply. Shake can before use. Apply spray directly to surface to be treated at a distance of 15 to 20cm to remove all residues that may interfere with electrical contact. Tilt surface during cleaning. Allow excess liquid to dry completely before restoring power. To avoid accidental damage, always check manufacturer's instructions before applying product to equipment. Do not spray into cavities, openings, crevices or areas of your equipment where this product does not have sufficient airflow to support complete evaporation. Tilt the surface during cleaning to allow excess liquid to drain and the product to dry completely before returning it to service and connecting it to the electrical circuit.

Content: 300 Milliliter (€33.27* / 1000 Milliliter)

€9.98*

8329/01 FG Contact spring for plug cap - 1pce.

Spare part for Solo engines.

€5.20*

40001/40002 Samba Moca carbon Airbox, for 1:5 touring cars

Genuine Samba spare/option part. Moca Racing air box carbon ultralight with aluminum adapter, foam filter and breakage protector.DMC no. 5-1801.Contents:1 set

€119.00*

This product is currently not available.

TLR0001 TLR 5ive-B instruction manual

Genuine TLR spare/option part.Printed instruction manual as included with every new Losi 5ive-B.Languages:GermanEnglishFrenchItalienischSpanishDimensions:Height: 295 mmWidth: 215 mm87 pages

€19.90*

6547/01 FG Receiver cable FG gold contact/Multiplex - 1pce.

Receiver cable, ready-made with FG gold contact plug-in system for Multiplex plug.total length 20-25cm

€7.10*

y1590 Subaru Impreza Ralley Monte-Carlo 99 Decal set

Decal set fits y1589 Subaru Impreza Monte-Carlo 99 body shell.Contents:1 piece

€29.90*