6492 FG Steel spur gear 46T with adapter - set

Genuine FG spare/option part. Gearwheel protection in transparent polycarbonate for all 1:6 Off-Road, Monster-Beetle, Big-Foot and Truck models with the gearwheels 43, 44, 46, 48 teeth. Protects the driving gearwheels almost from dirt, sand and stones. We recommend the mounting when driving on car parks and Off-Road ground. Not suitable for Formel 1, Leopard 2 + 4 Competition, Competition and Competition Evolution models.Contents:1 piece

Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Attention: not suitable for 1/6 scale Smartech / Carson 2WD Off-Road models. (Link to the Carson Smartech pinions: here)Pinions up to 16T can be used on the layshaft as well.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Teeth:Item no.:13 Teeth HT y026814 Teeth FG 604614 to 48 Teeth HT y011615 to 48 Teeth FG 604715 to 48 Teeth HT y19354 wide16 to 48 Teeth FG 643116 to 48 Teeth FG 6431/1 wide17 to 48 Teeth HT y19355-116 to 46 Teeth HT y011917 to 46 Teeth HT y1935518 to 46 Teeth FG 643219 to 46 Teeth HT y1935718 to 44 Teeth HT y012319 to 44 Teeth FG 6432/220 to 44 Teeth FG 643321 to 44 Teeth HT y1935820 to 42 Teeth HT y090421 to 42 Teeth FG 7431/2122 to 42 Teeth FG 743121 to 40 Teeth FG 7432/2122 to 40 Teeth FG 7432/2223 to 40 Teeth FG 7432/2324 to 40 Teeth FG 743225 to 40 Teeth FG 7432/2526 to 40 Teeth HT y1936426 to 38 Teeth FG 7433Contents:1 piece

Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5cm³ cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

Item N° 6432 Steel pinion 18 teeth - 1pce.For combination with 46T main spur gear.Diameter 29,7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5

Small alloy engine mount.Suitable for Marder, Beetle, Pajero and Monster with CY / Zenoah G230/240/260/270/290 engine.

Genuine FG spare/option part.Spare part for FG no.: 6464.Dimensions:Inner diameter: 20 mmHeight: 71 mmContent:2 pieces