6118 FG Radio plate 04 for 1:6 models
€25.90
Available
Product information "6118 FG Radio plate 04 for 1:6 models"
Radio plate with a new design. Suitable for all FG 1:6 Off-Road models except Leopard. This set includes the battery mount.
Contents:
- 1 set
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Alternatives
Genuine HT spare/option part. Universal radio plate for FG 2WD Marder/Beetle/Off-Road Buggy/Pajero an all Monster and Stadium models. With drilling templates for the following steering servos:Hitec HS-805BB/HS-5745/5735/Orange Power MPX Jumbo und Rhino The size of the steering servo can vary because you can adjust the position of the aluminum tray bar to accomodate larger or smaller servos. You will need FG adapters for installation of the gas / brake servo: #5014/04 servo mounting frame for (standard sized) Futaba / JR, Thunder Tiger DS1015 - 2pcs. Accepts FG servo frames for up to two throttle/brake servos (not included). Spacers for rx-box installation are included.Old version chassis plates (~pre 2003) have a different bolt pattern. When installing this radio plate on an old chassis new mounting holes must be drilled into the chassis plateThe surface is plain aluminum. With the necessary effort it can be polished to a high luster.Contents:1 piece
Accessories / Spare parts
Genuine FG spare/option part. Suitable for rc-plate 5014.Dimensions:Inside length: 44 mmInside width: 20,5 mmContents:2 pieces
Item N° 6534/02 Throttle pivot post 3.1mm - setRevised set for 2 mm linkages, but with 3.1 mm pivot bore to prevent linkage seizing. Can be used for throttle or brake applications.Set collars have 2.1 mm inner diameter.
Genuine FG spare/option part. Splash-proofed receiver box for all merchantable small receivers, suitable for all car models 1:12 - 1:5.Dimensions:Length: upper section 92 mm, bottom 69 mmHeight: 48 mmWidth: 38 mmContents:1 piece
Original FG Ersatz-/Tuningteil. Spare part for 6118 and 6118/01.Contents:1 piece
Customers also bought
Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5cm³ cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.
Genuine FG spare/option part.Spare part for FG no.: 6464.Dimensions:Outer diameter 61 mmInner diameter 20 mmHeight 71 mmContent:2 pieces
Genuine FG spare/option part. Side guards suitable for Marder, Off-Road Buggy 2WD and 4WD body.Contents:2 pieces
Genuine FG spare/option part. Individual prices of the parts in the tuning set: 847,06 EurosAluminum conversion kit to aluminum front axle and aluminum rear knuckle and wishbone for FG Marder.Contents:1 set
Genuine FG spare/option part. Splash-proofed receiver box for all merchantable small receivers, suitable for all car models 1:12 - 1:5.Dimensions:Length: upper section 92 mm, bottom 69 mmHeight: 48 mmWidth: 38 mmContents:1 piece
Customers also viewed
FG Modellsport stickers, set includes 2 pcs. of size 230x110mm and 4 pcs. 110x55mm.
Genuine FG spare/option part. Relocates the starter handle to the roll cage.Wire diameter 1.9 mm.Contents:1 piece
Genuine FG spare/option part.Contents:1 piece
Genuine FG spare/option part.Fits all FG 2WD and 4WD off road cars except Leopard and Leopard race or for CY / Zenoah G230/240/260/270.Contents:1 piece
Genuine HT spare/option part. Conversion kit for FG 1/6 scale 2WD Off-Road models and Smartech Uno/Carson Attack to Mega Beetle.The 8.5 x 1.0 mm female thread perfectly fits the usual stock 8 mm body mounts non-cutting. The thread depth of about 22 mm allows for about 10 - 15 mm of body position adjustment!Content of this set:2 pieces of front body mount (item no. 7154)2 pieces of side body mount (item no. 7154/01)2 pieces of rear roll cage mount (item no. 305001)2 pieces of aluminum body mount extension (item no. y1452)4 pieces of body clip (item no. 6013)4 pieces of M4 x 25 mm worm screw for installation of side and front mounts
Genuine FG spare/option part.Plastic bolt for battery holder.Contents:2 pieces