6069/01 FG Differential axle spline drive

€29.00*

Available

Product number: fg_6069_01

EAN: 3410564505724

Product information "6069/01 FG Differential axle spline drive"

Genuine FG spare/option part.

For all FG cars with standard drive shafts (no ball drive). Accepts dogbones with 10 mm ball and 4 mm pin.

Dimensions:

Shaft, diameter: 8 mm
Length: 27 mm
Spline drive for FG bevel gears
Cup, diameter: 18,5 mm
Length 14 mm

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Alternatives

GPM 9472 Ball drive conversion kit for FG Marder, Off-Road, Beetle, Monster/Stadium, Formula 1 and Truck cars

Fits all FG offroad (like Marder, Off-Road Buggy, Beetle) / monster and stadium models (except Leopard 2010 up). Also for FG Formula 1 and Race Truck models.The ball drive conversion kit for FG touring cars and gt-models you will find here: GPM 9471. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM ball drive set includes everything for a conversion of the respective FG car. Set includes:Quantity:DescriptionPart number2 piecesBall drive wheel shaftGPM 6079/012 piecesDifferential ball drive cupGPM 6069/022 piecesBall drive shaft 96,5 mmGPM 6080/014 piecesDrive shaft booty100412 piecesSteel ballGPM 7080/024 piecesDrive shaft spacer springy1218

€149.90*

y1004 Driveshaft boots for ball drive + dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

y1218 Springs for drive shafts

Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

y0809 Klüber high performance grease for differentials

Freaking expensive, but it is damned fine.ASONIC HQ 72-102 is a synthetic high-temperature lubricating grease, for use in limited slip differentials. Due to the careful selection of product components and the clean manufacturing environment, ASONIC HQ 72-102 is a rolling bearing grease with a particularly low noise level.Benefits for your application:High-temperature lubricating grease for rolling bearingsHigh purityLow noiseGood water resistanceContent:1 piece, tube with 30g

Content: 30 Gramm (€730.00* / 1000 Gramm)

€21.90*

Accessories / Spare parts

y1218 Springs for drive shafts

€4.90*

y1004 Driveshaft boots for ball drive + dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

Customers also viewed

6069/02 FG Differential drive cups for ball drive - 1pce.

Genuine FG spare/option part. Spare part for FG ball drive.Dimensions:Shaft:Diameter: 8 mmLength: 27 mmSpline drive: for FG bevel gearsCup:Diameter: 18,5 mmLength: 18 mmContents:1 piece

€35.00*

68277 FG Front driveshaft 4WD

Genuine FG spare/option part.Dimensions:Diameter: 7,10 mmTotal length: 107,5 mmContents:1 piece

€17.50*

8484 FG Alloy differential for 1:5 and 1:6 conversion kit

Genuine FG spare/option part. The conversion kit includes all parts needed for a conversion from a standard plastic differential to a non-adjustable alloy differential.Content:1 set

€101.95*

y1016 Zenoah G320RC with Walbro carburetor WT1107

With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.With the new "K & N" version of the Losi DBXL there is another detail, which need to be considered.From the very beginning the hole pattern for the engine installation in the DBXL chassis plate was no precise match to the hole pattern of the engine, even when delivered in stock form with standard engine. Now with the "K&N" version the engine mount has been changed to eliminate this discrepancy. However, all aluminum engine mounts available on the market share their dimensions with the previous plastic engine mount. For the installation of a G320 Zenoah in a "K&N" -DBXL two possible combinations exist in order to obtain the correct hole pattern:When using the standard (new) plastic engine mount a shortened clutch housing is required as in a 5ive-TWhen using an aluminum engine mount a stock length clutch housing is requiredSeparately, it is recommended to enlarge the cutout in the body panel in front of the K & N air filter for about 2 - 3 mm to ensure that the panel cannot chafe on the air filter.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€339.90*

Details

y0039 Oil for shock absorber, all viscosities, 100 ml

Genuine silicone shock absorber oil for the optimal shock absorber set-up. Content: 100 ml Please note: Factory filling of FG/Losi/Smartech and many other 1/5 and 1/6 scale shocks is done with genuine silicone shock absorber oil. To ensure seal tightness and consistency you should only use genuine silicone shock absorber oil for refilling as well.Most every rc-car shock absorber uses silicone oil of different viscosities. The smaller the number, the lower the viscosity of the silicone oil and the softer the damping. As a rule of thumb: Viscosity 100 = similar to water Viscosity 1.000 = similar to cooking oil Viscosity 5.000 = similar to shampoo Viscosity 10.000 = similar to honey As a reference: The red FG Marder / Off-Road Buggy series shock absorbers are factory filled with 2.000 viscosity oil, the shocks on monster cars with dual shock set-ups (total of 8 shocks) are filled with 1.000 viscosity oil, and the shocks on FG onroad cars come filled with 4.000 viscosity oil. The original filling of the Losi 5ive-T is 350cc silicone oil.FG Silicone oil with 100 ml:FG Item N° 66295/010 = Viscosity: 100 FG Item N° 66295/025 = Viscosity: 250FG Item N° 66295/035 = Viscosity: 350FG Item N° 66295/050 = Viscosity: 500FG Item N° 66295/075 = Viscosity: 750FG Item N° 66295/100 = Viscosity: 1000FG Item N° 66295/150 = Viscosity: 1500FG Item N° 66295/200 = Viscosity: 2000FG Item N° 66295/300 = Viscosity: 3000FG Item N° 66295/400 = Viscosity: 4000FG Item N° 66295/500 = Viscosity: 5000FG Item N° 66295/600 = Viscosity: 6000FG Item N° 66295/700 = Viscosity: 7000FG Item N° 66295/800 = Viscosity: 8000FG Item N° 66295/900 = Viscosity: 9000FG Item N° 66296 = Viscosity: 10000Viscosity of silicone oil at various temperatures.

Content: 100 Milliliter (€154.00* / 1000 Milliliter)

From €12.90* €15.40* (16.23% saved)

Details

GPM 6069/02 Ball drive differential drive cup for all FG and Mecatech cars, 1 pce.

Fits all FG cars and the Mecatech FW01. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins. The GPM ball drives can be partially mixed with FG parts. The heads of the GPM driveshafts fit into FG differential cups or wheel shafts.The opposite combination, i.e. FG shafts in GPM differential cups or wheel shafts does not always fit. We had tests where some FG shafts fit neatly, but due to slight tolerances others who did not fit into the very same cups/shafts. For this combination, we can not guarantee compatibility! Dimensions: Diameter: 8 mmTotal length 45 mm

From €34.90*

Details

6064 FG Differential case

Genuine FG spare/option part. Stock plastic differential case. Also available in aluminum.Dimensions:Length: 70 mmDiameter: 42.5 mmFlange diameter: 65 mmBearing seats: 12 x 8 mmShaft bore: 8 mmInner dimensions: 40 x 30 mmContents:1 piece

€27.00*