Servo direct power supply cable, 1 pce.
Product number:
servo_strom_ohne.2
EAN:
4058575018933
Product information "Servo direct power supply cable, 1 pce."
Servo direct power supply cable, 1 pce.
With this cable the servos get their current directly from the battery without straining the receiver circuit board.
Silicone insulated wires with 0.5 mm² cross section
With this cable the servos get their current directly from the battery without straining the receiver circuit board.
Silicone insulated wires with 0.5 mm² cross section
Login
Accessories / Spare parts
Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece
Similar products
%
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece
Genuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece
y0657 Connector:
y0657/01 Futaba, JR, MPX universal
Genuine HT spare/option part. 5 cells, 6 volt, cell size Sub-C. More applications on request.Dimensions: approx 112 x 46 x 23 mmContents:1 piece
The RHINO pro SHV digi 4 servo is a 29 mm digital servo designed for use in large-scale models. The new pro SHV servo is faster, more powerful, and more durable than the proven RHINO digi 4, of which thousands are now in use. More performance, with higher torque and faster transit speed, and more durable with a new triple-ballraced heavy-duty steel gear set. The operating voltage range has been expanded to 7.4 V, allowing the servo to be operated directly with up to two-cell LiPo batteries.Large 1 : 5 scale model cars make very exacting demands on the servos, and for many years the RHINO servo has set the standard with its extremely robust, outsize metal gearbox and 8 mm output shaft for the output device. An integral aluminium heat-sink cools the motor and electronics very effectively. Servo case gaskets make the unit dust-proof and splash-proof. The enormous power and robust nature of this servo also make it an excellent choice for large models generally, such as F3A - XXL large-scale model aircraft, as well as for non-standard applications.Adapter FG # 6118/02 is required for installation into a FG/Smartech car.High-voltage (HV) servosHV servos have a broad operating voltage range of 5 - 7.4 V, i.e. they can be operated directly with two-cell Lithium-based rechargeable batteries (e.g. LiPo, LiFe, LiIo). The outstanding features of LiXX batteries compared with NiXX types are their higher energy density and lower self-discharge rate, and for these reasons they are increasingly used as power supplies in model RC systems. The higher voltage of LiXX batteries means that the current drawn by an HV servo is lower for a given output power than that of conventional servos, which are generally designed for a nominal voltage of 4.8 - 6 V. When used with 2S LiXX batteries, these older servos must therefore be operated with a separate voltage reducer. This reduces the overall efficiency of the system, leads to unnecessary dissipated power, requires additional electronic complexity and more connectors ( higher costs, greater failure risk, higher weight). Modern receivers (e.g. M-LINK) are designed for voltages up to 9 V, i.e. with HV there is no longer any reason not to use the modern, superior LiXX battery technology.The following servo parameters can be adjusted using the MULTImate test and programming unit # 8 2094:Direction of servo rotationServo transit speedServo travel, left / right (max. 2 x 90°)Servo centreServo deadbandFail-safe (On with servo Fail-Safe position / Off)Reset to factory default settingsSpecificationDimensions (L x W x H):Weight::Gearbox:Ballraces:Multi-finger wiper pot:Torque @ 6 V / 7f.4 V*:Holding power @ 6 V / 7.4 V*:Transit speed for 40°@ 6 V / 7.4 V*: 59 x 29 x 55 mm172 gSteel3yes (with indirect drive)230 / 270 Ncm280 / 320 Ncm** 0,10 / 0,08 sec.* 5-cell NiXX / 2S LiPo operation. Values measured at stabilised 6.0 V / 7.4 V.** Holding power at angular error
servo_strom_ohne Application:
y0363 - 2 servos, battery connector none,
Servo direct power supply cable, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.Silicone insulated wires with 0.5 mm² cross section
For the secure installation of driveshaft boots.
Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum radio plate from ATOP, fits Losi 5ive-T 1.0 and 2.0.This all-aluminum unit allows for installation of dual steering servos. The servo hole patterns are suitable for Losi original servos / servos with the size of 900S and K-Power.The box for the receiver battery has internal dimensions of 142 x 65 x 32 mm.Available with additional genuine Losi S900S 5ive-T steering servo incl- Y-harness in the options menu.Contents:1 piece
Reliable water protection for all electronic components.In model making too, WET.PROTECT protects and secures the functionality of precision mechanics and electronics of filigree electrical components and control units.Even out in the field and moisture and soddenness go into every little opening and every ever so narrow gap. With WET.PROTECT , moisture, splash water and rain have no chance to develop their destructive effects. WET.PROTECT protects with a single application against corrosion and moisture for at least one year, even during regular, intensive off-road use.A product, which is able to isolate metals to 100% against any wetness or humidity. Conventional contact sprays emulsify, therefore mix themselves with water, which provides a band aid solution, but no long-lasting operability, let alone real protection.WET.PROTECT goes completely between surface and water and isolates them by a hermetic and long lasting protective film.The conductivity is not impaired in any way, however corrosion and short-circuits are eliminated. Once applied, WET.PROTECT provides protection for up to one year.Technical details:Appearance:slightly brownish liquidOdor:Solvent-likeDensity at 20° C:0.6 kg / liter (canned)Flash point:Not measurable (aerosol)Ignition temperature:>250°CSelf-igniting:not self-ignitingSolubility in water:immiscible, non-emulsifyingLayer thickness:2 3 µmSurface resistance: 28 Terra Ohms (ISO93)Dielectric strength:208 KV/cm (normal case)The product is extremely economical in application. The more the better does not apply!Contents:1 piece / 50 ml
Content: 50 Milliliter (€258.00* / 1000 Milliliter)
Cable tie for one time tightening / sealing / fastening. For example on drive shaft boots, fuel hoses, brake lines and many more.With steel tongue for infinite adjustment and increased holding power. Especially for high demand applications.Size: 2.5 x 200 mmTemperature range: -40°C to +85°CContent: 20 pieces
Genuine rc-car-online spare/option part. Total length:approx. 200 mmContents:1 piece
Genuine HT spare/option part. Abrasion protection for cables, fuel tubes and hydraulic brake lines. Pack with 1 m. Small, for cables from 1.5 to 8 mm diameter.Contents:1 piece / 1 meter
Customers also viewed
%
Incl. 2x TopTuning 3S 3100mAhFor those who want the biggest, baddest RC rock crawler ever, the legendary Axial® Honcho is now available on the 1/6 scale SCX6 4WD platform. With its 2-speed transmission and powerful Spektrum Smart electronics, this massive RTR is an absolute beast! Key Features Based on the legendary Axial® Honcho New vehicle option on the SCX6 platform Increased performance due to body design Two-speed metal gear transmission Spektrum Smart 3-channel radio and electronics The 1/6 scale Axial® SCX6 platform has taken RC rock crawling into a whole new dimension, armed with a huge amount of detail and high-performance functionality. Now, Axial has expanded the SCX6 lineup with an exciting 1/6 scale version of the insanely popular Honcho. Whether you're a fan of the original SCX10 Honcho, a rock crawling enthusiast, a large-scale aficionado, or all of the above, the Axial SCX6 Honcho 4WD RTR is sure to please. It's the biggest, baddest RC rock crawler ever!The SCX6 Honcho is engineered for extreme durability and performance, as shown by its AR90 axles with metal ring and pinion gears and front offset pumpkin. For optimal handling, the chassis has a three-link front and four-link rear suspension setup and metal links are used at all suspension points. The transmission offers high and low gears out of the box, with a Spektrum S614 metal gear high-torque servo included and installed for the two-speed linkage.Molded from high traction compound with an aggressive tread pattern, the massive, 7" tall, officially licensed Falken Wildpeak M/T tires provide excellent grip and ground clearance over dirt, rocks, and all other off-road surfaces. They're mounted on officially licensed Black Rhino Primm beadlock wheels for easy removal and replacement without gluing.With the included Spektrum DX3 radio, you'll enjoy the superior range, response, and interference resistance of exclusive DSMR® technology. Together with the installed Firma Crawler 120A Smart Sensored-Brushless ESC, it also comes ready to deliver the telemetry advantages of exclusive Spektrum Smart technology. Install a Spektrum Smart LiPo battery and you can view vehicle battery capacity on the transmitter's voltage level indicator. Outfit the DX3 with the optional BT2000 Bluetooth module, download the free Spektrum Dashboard app to your smart device, and you're ready to use more real-time Smart telemetry without needing on-board sensors or modules.Measuring over 2-1/2 feet long and topped off with a modernized Honcho body, the Axial SCX6 Honcho 4WD RTR is the rig that will take your rock crawling and climbing adventures to an exciting new level. Just add your choice of suitable battery and aim for the top! Features 1/6 scale chassis design is based on the proven SCX10 III Metal gear transmission comes configured for two speeds with high and low gears Durable three-link front and four-link rear suspension provides optimal handling AR90 axles feature metal ring and pinion gears Replica V8 engine cover adds to the realistic appearance Spektrum DX3 2.4GHz DSMR® radio provides superior range, response, and interference resistance and is compatible with Smart technology Spektrum Firma 120A Smart Brushless Crawler ESC feeds telemetry data to the DX3 transmitter in real time Includes a powerful Spektrum S905 high-torque, large scale steering servo (also accepts larger 1/5 scale servos with the included adapter) Modernized Honcho body with rear tube cage includes interior detail High-traction, 7" tall, officially licensed Falken Wildpeak M/T tires are mounted on officially licensed Primm Black Rhino beadlock wheels SCX10 III Based Chassis DesignInspired by the proven SCX10 III, the SCX6 platform follows a similar design while increasing the size to meet large scale needs and expectations. 2-Speed Metal Gear TransmissionOut of the box, the SCX6 Honcho 4WD RTR is configured for two speeds with high and low gears. A Spektrum S614 Metal Gear High-Torque Servo is included for the two-speed linkage. This feature provides a true crawling gear ratio while also allowing you to shift for more speed. AR90 AxlesThe AR90 axles feature metal ring and pinion gears with a front offset pumpkin. The 3-piece front axle accommodates optional aluminum carriers and steering knuckles. "Hi-steer" steering knuckles raise the steering tie rod for increased ground clearance. The rear axle can be set up for optional rear steering. Replica V8 Engine CoverThe molded engine cover captures the look of a modern V8 engine. It not only enhances the scale realism but also serves as the ESC mount and receiver box cover. 3-Link Front/4-Link Rear Suspension The SCX6 suspension geometry matches the SCX10 III with metal links used at all suspension points for durability. 1/6 Scale Steering ServoSteering is controlled by a Spektrum S905 high-torque, large scale servo. The servo mounting location will also accept an optional 1/5 scale servo if you choose to modify your rig. Spektrum Sensored Brushless Rock Crawling ESCIncluded and installed, the Spektrum Firma 120A Smart Brushless Crawler ESC provides throttle input to the massive Firma 1200Kv Sensored Brushless Motor. The motor itself weighs in at 1.75lb (.780kg) and gives this beast enormous power and realism! Officially Licensed Falken Wildpeak M/T TiresThe 7" tall, officially licensed Falken Wildpeak M/T tires are molded from a high traction compound and feature an aggressive tread pattern. They provide excellent grip and ground clearance over dirt, rocks, and other off-road surfaces for nonstop climbing and crawling. Officially Licensed Black Rhino Primm Beadlock WheelsThe SCX6 Honcho crawler's officially licensed Black Rhino Primm beadlock wheels add realism and allow easy tire removal and replacement without gluing. In The Box (1) 1/6 SCX6 Honcho 4WD RTR (1) Spektrum DX3 Smart DSMR® 3-Channel Radio with SR515 receiver (1) Spektrum Firma 120A Brushless Smart Crawler ESC (1) Spektrum Firma 1200Kv Sensored Brushless Crawler Motor (1) Spektrum S905 High-Torque 1/6 Scale Steering Servo (1) Product Manual (4) AA Transmitter Batteries
servo_strom_ohne Application:
y0363 - 2 servos, battery connector none,
Servo direct power supply cable, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.Silicone insulated wires with 0.5 mm² cross section