15460 HPI Carburetor WT-668

€99.80*

Prices incl. VAT plus shipping costs

Available

Product number: hpi.h15460

EAN: 4058575013679

Product information "15460 HPI Carburetor WT-668"

Genuine HPI spare/option part.

Content:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Alternatives

y0251 Performance carburetor with accelerator pump type: WT-813A

Genuine Walbro spare/option part. Fits Zenoah G230/240/260/270 engines and their CY/HPI Fuelie clones as well.Walbro WT-813A carb with accelerator pump, improves low end response when the engine is tuned for maximum performance. 15,88 mm bore, 12,7 mm venturi. Ready for installation with modified shaft already installed. Contents:1 piece

€79.90*

Carburetor Walbro WT 990

7855 Carburetor type: Walbro WT990 Standard carburetor for Zenoah G290. Typ: Walbro WT990 Fits all Zenoah G230/240/260/270 and 290 engines as well as the respective Chung-Yang (CY) versions, also Losi and HPI Fuelie, Smartech, Carson PT engines, and many others.

€79.90*

Configure now

Similar products

6061 Mielke pull starter with hybrid starter function

Genuine Mielke spare / option part.Starting by pull starter or by cordless screwdriver or electric starter is possible.Pull starter with hybrid starter function. Who does not know it? A torn starter rope, blisters on your finger from constant pulling or a defective starter pawl. All these problems are a thing of the past with the hybrid starter.With the help of a cordless screwdriver the engine can be started very easily and if the battery of the cordless screwdriver is empty, the engine can be started by using the conventional way with the pull-rope starter.Please note:The starter shaft for electric start is inserted in a straight line in extension of the crankshaft. No part of the vehicle must be in the way here. On a model with a longitudinally mounted engine (e.g. Losi 5ive or DBXL vehicles) the rear axle will usually prevent the use of the electric start. The normal pull start by cable remains possible.Contents:1 piece

€114.90*

6062 Mielke clutch nut for E-start shaft

Genuine Mielke spare / option part.Spare part for Mielke 6061.Contents:1 piece

€24.90*

7340/09 FG Rubber cap for kill switch

Genuine FG spare/option part.Protects the switch against dirt and splashes. Highly recommended for off-road use.Contents:1 piece

€3.90*

7305/08 FG Crankcase gasket for CY / Zenoah

Genuine FG spare/option part.For Zenoah G230/240/260/270/290 enginesApplications:Click here!Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece

€4.30*

6061/01 Mielke Zenoah Hybrid starter, pullstart unit only

Genuine Mielke spare / option part.Spare part for Mielke 6061.Contents:1 piece

€69.90*

Details

15411 HPI Air filter set Baja B5

Genuine HPI spare/option part. Content:1 piece

€54.80*

7379/08 FG Choke lever for CY / Zenoah / Fuelie

Genuine FG spare/option part.Contents:1 piece

€3.90*

15416 HPI Air filter Foam element Set for 15411

Genuine HPI spare/option part. This is a set of foam elements to complete the air filter on the Baja 5B. Be sure to follow the installation instructions in the Baja manual when installing these on your Baja!Contents:3 pieces

€21.99*

15431 HPI Crankshaft nut and key

Genuine HPI spare/option part. Content:1 piece

€8.79*

15446 HPI Clutch Housing

Genuine HPI spare/option part. High quality spare part to provide easy maintenance and repairs for the Fuelie engine.Content:1 pieces

€38.39*

15443 HPI Step Screw M6 x 23 mm

Genuine HPI spare/option part. Part is delivered in silver or black color from vendor!Content:2 pieces

€15.29*

15453 HPI Engine stop switch

Genuine HPI spare/option part. Content:1 piece

€9.89*

Customers also viewed

Carburetor Walbro WT 1107 with choke normal/ball-raced

Walbro Vergaser WT1107 with choke Standard carburetor for Zenoah G320. Typ: Walbro WT1107This is the stock carburetor used for the G320RC engine, and will also work on all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³. Dimensions:Bore: 15,88 mmVenturi: 13,5 mmIndependent tunable high and low speed jets.The carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³.

€69.90*

Configure now

y0251 Performance carburetor with accelerator pump type: WT-813A

€79.90*

Carburetor Walbro WT 668B/668C with choke normal/ball-raced

Alternative: Walbro 603B also with choke. But with better manufacturing quality!The Walbro WT668B carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc. The Walbro WT668B features an integrated choke with lever and a throttle shaft linkage lever.The WT668B is also available with ball-raced throttle shaft under part number # y0036/04 Ballraced tuning Walbro WT668B carburetory0036/04 Ballraced tuning Walbro WT668B carburetorWith dual ball bearings on the throttle shaft. Two sealed bearings 2RS type (3/16" x 5/16" x 1/8") shielded by two steel plates (5 x 8 x 0.3 mm). High quality processed and optimized for racing use! The soft stock screw holding the throttle lever has been replaced with a high strength Allen key screw. Since all screws on the carb are imperial sized, so is the key for this screw. A corresponding bit is included in our tool set y0785, or you can use Allen key wrench y0037/03 as well.The Walbro WT668B carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc. The modified Walbro WT668B features an integrated choke with lever and a throttle shaft linkage lever.The Walbro WT668B carburetor is also available in a standard version under part number # y1067 Walbro WT668B carburetor.

€69.90*

This product is currently not available.

Carburetor Walbro WT 990

€79.90*

Configure now

Carburetor Walbro WT 603B with choke, ball-raced

7355/08 Carburetor type: Walbro WT 603BStandard carburetor for Zenoah G230/260. Carb has integrated choke. Typ: Walbro WT603B y0036/01 Ball-raced tuning carburetor Walbro WT 603B-RacingWith dual ball bearings on the throttle shaft. Two sealed bearings 2RS type (3/16" x 5/16" x 1/8") shielded by two steel plates (5 x 8 x 0.3 mm). High quality processed and optimized for racing use! The soft stock screw holding the throttle lever has been replaced with a high strength Allen key screw. Since all screws on the carb are imperial sized, so is the key for this screw. A corresponding bit is included in our tool set y0785, or you can use Allen key wrench y0037/03 as well. Ball-raced Zenoah G230/260 stock carburetor. Fits all Zenoah G230/240/260/270/290/320 engines as well as the respective Chung-Yang (CY) versions, also Losi and HPI Fuelie, Smartech, Carson PT engines, and many others.Normal:Ball-raced:

€88.90*

MadMax SUPER GRIP Soft 170x80/x60 for FG, Smartech, HPI, Losi, Arrma & Co.

SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 18 mm square or 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced silver beadlock rings. Fits FG, Smartech, Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T and Super Baja Rey should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!

€109.90* €129.90* (15.4% saved)

Configure now

15465 HPI Air filter gasket

Genuine HPI spare/option part. Content:2 pieces

€6.58*