8 products found for "fg_7800"

Catalogue #1

7800 FG Zenoah G290RC with Walbro carburetor WT 990

Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5cm³ cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€280.60*

7100 FG Adjusting clip for 16 mm axle, 16 pcs.

These adjusting clips allow a faster adjustment of the wishbones. Suitable for front and rear suspension. The set contains 16 adjusting clips in 2 and 6mm size for 6 mm axles.

€9.50*

7080 FG Rear dogbone 90 mm

Genuine FG spare/option part. Standard driveshaft, short version.Fits FG Audi, BMW 320, Peugeot 307, Renault Megane und VW New Beetle.Dimensions:Shaft diameter: 7 mmBall diameter: 10 mmLength: 90 mmContents:1 piece

€22.50*

FG 7807 cylinder G290RC

Genuine FG spare/option part.Contents:1 piece

€96.40*

7808 FG Piston for Zenoah G290

Genuine FG spare/option part.Spare part for Zenoah G290 engine.Contents:1 piece

€39.90*

7809 FG Piston ring for Zenoah G290

Genuine FG spare/option part.Spare part for Zenoah G290 engine.Dimensions:Thickness: 1 mmContents:1 piece

€19.90*

7200 FG alloy shock absorber 04 short

Genuine FG spare/option part. The alloy housing has an outside thread to adjust the damper spring. The upper alloy shock absorber seal is equipped with a ventilation boring which makes the refilling if the damper easier. Completely new is the lower shock absorber seal with the plastic guiding bushes for the damper piston rod and for an easier chaning of the o-rings. The alloy adjusting ring has a socket for the spring collet and an adjusting mark. The shock absorber has an diameter of approx. 16 mm. Suitable for all damper springs with approx. 17 mm inside diameter .With 110 mm hole distance.Contents:2 pieces

€74.90*

7810 FG Piston pin for Zenoah G290

Genuine FG spare/option part.Contents:1 piece

€9.50*