6432 FG Steel pinion 18 teeth - 1pce.
€35.00
Available
Product information "6432 FG Steel pinion 18 teeth - 1pce."
Steel pinion 18 teeth - 1pce.
For combination with 46T main spur gear.
Diameter 29,7 mm
Bore 10 mm
Total width 18 mm
Tooth width 11.5 mm
Module: m=1,5
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Alternatives
Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Attention: not suitable for 1/6 scale Smartech / Carson 2WD Off-Road models. (Link to the Carson Smartech pinions: here)Pinions up to 16T can be used on the layshaft as well.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Teeth:Item no.:13 Teeth HT y026814 Teeth FG 604614 to 48 Teeth HT y011615 to 48 Teeth FG 604715 to 48 Teeth HT y19354 wide16 to 48 Teeth FG 643116 to 48 Teeth FG 6431/1 wide17 to 48 Teeth HT y19355-116 to 46 Teeth HT y011917 to 46 Teeth HT y1935518 to 46 Teeth FG 643219 to 46 Teeth HT y1935718 to 44 Teeth HT y012319 to 44 Teeth FG 6432/220 to 44 Teeth FG 643321 to 44 Teeth HT y1935820 to 42 Teeth HT y090421 to 42 Teeth FG 7431/2122 to 42 Teeth FG 743121 to 40 Teeth FG 7432/2122 to 40 Teeth FG 7432/2223 to 40 Teeth FG 7432/2324 to 40 Teeth FG 743225 to 40 Teeth FG 7432/2526 to 40 Teeth HT y1936426 to 38 Teeth FG 7433Contents:1 piece
Customers also bought
46 teeth gear wheel for the layshaft.Diameter 72 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece
Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5cm³ cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.
Small alloy engine mount.Suitable for Marder, Beetle, Pajero and Monster with CY / Zenoah G230/240/260/270/290 engine.
Hardened steel spur gear for FG 1/6 off-road models, spur gear diameter 72 mm.Module: m=1,5
Genuine FG spare/option part. Gearwheel protection in transparent polycarbonate for all 1:6 Off-Road, Monster-Beetle, Big-Foot and Truck models with the gearwheels 43, 44, 46, 48 teeth. Protects the driving gearwheels almost from dirt, sand and stones. We recommend the mounting when driving on car parks and Off-Road ground. Not suitable for Formel 1, Leopard 2 + 4 Competition, Competition and Competition Evolution models.Contents:1 piece
Customers also viewed
Genuine FG spare/option part. Rubber pucks for all standard design FG spur gear carriers.Dimensions:Outside diameter: 16 mmInner diameter: 7 mmHeight: 6 mmContents:4 pieces
Item N° 6432/02 Steel pinion 19 teeth - 1pce.For combination with 44T main spur gear.Diameter 32.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
Item N° 7431 Steel gearwheel hardened 22 teeth - 1pce.Suitable for 42 teeth main gear wheel.Diameter 35,7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5
Item N° 6431/01 Steel pinion 16 teeth, wide - 1pce.For use on the clutch bell of FG monster cars.Diameter 26.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5
Genuine Top Tuning spare/option part. Motor pinion made of nitrided hardened steel, module 1.5 and 8 mm bore. Reinforced hub for set screw M5x6. The pinions with odd tooth counts are profile shifted. Within the same outer diameter, there is no need to adjust the backlash when changing the pinion. When mounting on vehicles with mounting holes in the motor mount that are specific to the tooth count, the mounting holes for the higher number of teeth in each case (16 or 18) must be used.Profile regraded:This means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter. Available in two sizes with two tooth counts:Outer diameter 30 mm with 17T or 18TOuter diameter 27 mm with 15T or 16TContents:1 piece
Item N° 7433 Steel gearwheel hardened 26 teeth - 1pce.Suitable for 38 teeth main gear wheel.Diameter 41.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5