y0994 Marston heat-proof sealer - 1pce.

Bindulin liquid rubber - very high elasticitySuitable for additional sealing of tuned pipes and exhaust / manifold connections .Temperature resistant from -60 ° to + 180 ° CResistant against diluted acids.Also for sealing threaded joints, electric lines and cable lead-throughs in receiver boxes.The surfaces must be clean, grease free and dry (brake cleaner).Contents:1 piece / 45 grams

The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, the intake is flow-optimized. the case is specially matched with enlarged and flow-optimized cross section towards the ports Cylinder modified for installation of the ignition systemPiston:Transfer port area optimized for flow, weight reduced and the piston-roof is flow-optimized and polishedCrankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed. Cylinder gasket installed using elastic gasket sealer.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.

Genuine MD spare/option part. The red version with a temperature resistant up to 300°C. Directions for use:Clean the surfaces with a cleaner. Apply MD-Sil on one side and press the parts together. Touch-dry in 10 - 20 minutes. Curing speed 3 mm/24 hours. Contents:1 piece / 80 ml

The FG Off-Road Buggy WB535 is presented with a longer wheelbase and a pleasant design. All-wheel-drive, completely mounted ready-to-drive, combined with the open Off-Road Buggy body shell with metal roll cage and gigantic Off-Road rims with low-profile knobbed tires.The body shell is standard unpainted. Equipped with a 26cm³ engine the Off-Road Buggy is aggressive and also a tremendous jumper. The 35 mm wheelbase extension results in a higher tracking stability. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.According to side rails and the closed body shell the Off-Road Buggy Buggy is almost protected against dirt from underneath. The two-parts body shell is made of polycarbonate, the rear spoiler is made of impact resistant polyamide. Driver´s coverage and roll cage parts are made of aluminum. The giant low-profile knobbed tires are glued on black rims.The model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. The RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.Measures:Length: 770 mmWidth: 480 mmHeight: 280 mmWheelbase: 535 mmWeight: 10,8 kg

Race ported top end set for Zenoah G230 engine.The SPEED TEC CRANK genuine Zenoah G230 race ported top end set is optimized for performance with sophisticated craftsmanship and when accurately installed - guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC CRANK version modifications: Cylinder: Adjustment of compressionEnlarged portsFuel management milledMachined and polished exhaust and intakeThe case is specially matched with enlarged and polished cross section towards the ports Piston: Weight reducedSkirt shortenedOil ringsPiston above and below piston ring tapered and piston dome polished The set includes the following items: Performance-optimized cylinder and piston, piston ring, piston pin circlips and cylinder gasket.To achieve the optimum performance gain of a SPEED TEC CRANK top end set, we recommend the use of a tuned pipe ().Contents:1 set

Fits losi 5ive-T. Dimensions grommet:total length: 53 mm, down to 38 mm compressibleinner diameter: shaft 6 mm, shaft intake 19 mm Dimensions clamping ring: RW 20 galvanized, burnished for 20mm grommets Set content:Five x grommetTen x claming ring