y0811 After-Run, performance enhancing preservation for all 1/5 and 1/6th scale models, 20 ml

Dry lubricant instead of oilWe did not think that today its still possible to make a real improvement in lubricants!DryFluid Extreme is especially designed for remote control model cars, with the aim to maintain the functionality and durability of these little racers as long as possible or to even extend significantly.The effect of the new lubricants for shafts, bearings, guides and ball joints starts where other lubricants reach their limits. Low friction, high lubricity and minimal attractivity to dust or dirt were the main developmental targets. Recent findings in aerospace and automotive technology as well as the experience of RC car drivers are the mentors of innovation of this new lubricant.What is DryFluid Extreme RC-Cars?DryFluid lubricant is more of a solid lubricant than a classic fluid one. DryFluid is not a wax, not oiling, non-greasy and free of silicones. The use of dry particles, polymer lubricants and high-end lubricating fluids results in a previously unknown lubricity without binding dust and dirt. Ease of application and long-term effects of DryFluid Extreme will delight any modeler.DryFluid Extreme product featuresReduces the power losses of shafts, bearings and ball joint systems and guarantees a long life of the treated componentsLowest friction for smooth operation and wear reductionMultistage lubricant system with immediate and long-term lubrication effectsDoes not bind any dust or dirtExtremely good penetrating abilityHighest compatibility with all common materials like metals, plastics and rubberExcellent adhesion and corrosion protection propertiesThe use of DryFluid Extreme RC-CarsThe main effect of DryFluid Extreme is the reduction of friction and wear on shafts, bearings, guides and ball joint systems. The dry components do not bind any dust or dirt and ensure best possible long term lubrication effects.For best results the parts to be treated should be thoroughly cleaned and the fluid applied sparingly. Repeated use increases the long-term effect.Before use, shake bottle vigorously for a short time!Nanotec lubricant for joints, shafts, bearings and gears of rc-cars. Excellent long term lubrication effects. Use included put-on canula for fine dosing. Let dry for several minutes after application and close bottle tightly. Shake well before use Attention:Keep out of reach of children. Do not swallow. Avoid contact with eyes. Keep away from ignition sources. Keep bottle closed tightly.

Universal maintenance oil which has a high resistance to environmental influences; it is penetrating and moisture displacing with an excellent corrosion protection. Precise application is possible with the VL32 - Multipen's metal syringe tip. The ergonomic shape and rubberized handle provide a secure grip. Leakage of oil is prevented by the safety valve in the cap. Application: u> b>Pull off cap (avoiding strong pressure on the pen!), position the pen to the point of lubrication and press. Refit cap after use.Content:12 ml / 1 piece

Special oil for plastics in precision applicator; following special advantages:- Friction reduced ten-fold- Completely smooth running- Wear reduced by 90%- Resistant to fuel attack and ageing- Does not attack plastic materials- Temperature range -30°C to 150°C Applications:- Bowden cables- Ball-links and joints- Plastic differentials- Transverse armcontent 4ml

The maintenance can for all cars with a belt drive.Clean, light-coloured film for increasing tensile strength and care of many kinds of belts.Increases tensile force by up to 50 % for all kinds of V-belts, round and flat belts. Protects against drying out and wear, prevents belt squeaking and slip.

Special plastic cleanerPE100 was specially developed to protect plastics from external agents. The product penetrates right into the molecular structure of the plastic,which is thus protected from the inside out, remains permanently supple and retains its natural gloss.Most RC cars have various axle parts, such as control arms and bearing blocks made of plastic. Due to weather influences and especially UV rays,or contact with tire conditioners can cause the plastic to become brittle and weather over time.Especially with unpainted plastic, this process progresses relatively quickly. PE100 slows down this process and provides intensive protection,which significantly extends the life of the plastic. Also, the likelihood of seals and protective rubbers (e.g. bellows for drive parts) becomingbecome brittle are much lower.In addition to this protective effect, PE100 gives the plastic parts a fresher appearance. PE100 is also excellent for protecting electronic parts frommoisture in electronic parts. Das Produkt bildet eine wasserverdrängende Schicht und verbessert somit den Korrosionsschutz.In the spray can, PE100 is particularly user-friendly and practical to use. Thanks to the special nozzle with tube supplied, even difficult-to-reach areas can be treated effortlessly. Highlights H3>  span> clear, almost invisible fluid div>  span> Easy application div>  span> displaces moisture div>  span> Long-term effect div>  span> protects plastics against discoloring div>  span> holds rubber parts supple and prevents them freeze div>  span> protects ignition systems from moisture-related disorders div> div>> CONTENTS base: silicone oils, mineral oils and additives Density: 710 kg / m³ Consistency: liquid (firefitted in the aerosol can) viscosity: ± 15 mPa.s li> Flash point: 0 ° C compressive strength: minimal li> temperature resistance: -20 ° C to> 150 ° C li> water resistance: good li> acid resistance: resistant to dilute acids li> corrosion protection: good. Corrosion protection results from the formation of a water-displaced layer. Inputs: good li> lubricant content: 17% li> Processing conditions: + 5 ° C to + 40 ° C Underground: Most plastics, rubber and metal USAGEPreparation of the substrate: Provide a clean, dry, grease-free and non-corroded substrate.Shake can well before use. When used as a lubricant, spray the product directly onto the part to be lubricated. When used as a plastic and rubber protector, spray the product directly (spray distance 15-20 cm) or apply with a cloth or sponge. To achieve a beautiful shine, briefly polish the plastic with a clean, dry Multi Wipe. Material cleaning: With Innotec Multisol or Innotec Power Clean Hand cleaning: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water Shelf life: 2 years in unopened original packaging Storage conditions: Store in a cool, dry place Batch code type: F

Genuine Motul spare/option part. Motul Shine&Go, a silicone based care for all metal and plastic parts. Protects the surfaces with a long term non-stick protective film, helping to prevent dirt, grime, tire rubber and dust from adhering. Once applied after cleaning the model, dirt can be removed much easier next time.Contents:1 piece

With the integrated spray head can be changed between large-scale and precise spraying. The tube remains firmly at the spray head and is therefore no longer lost in the application. For surface spraying, the spray tube is simply folded down. With unfolded spray tube you can reach small spaces and can apply the product exactly accurately. Due to the 360 ​​° valve, the can can be maintained upright or overhead, so every application is possible.Protects against corrosion:Thanks to its corrosion-resistant formula, it offers long-lasting protection against rust and all forms of oxidation on metal surfaces.Temperature range: -50 to +150° C Eliminates squealEines der Hauptkomponenten ist ein aktives Schmiermittel, welches die Gängigkeit beweglicher Teile erleichtert und gleichzeitig Quietschen und Knarren beseitigt. Darüber hinaus schmiert es Teile und Mechanismen. Displaces moistureThe WD-40 multifunction product forms a perfect barrier against moisture by adding it. Thus, electrical and electronic mechanisms are always protected and creep currents are avoided. Cleans and protectsSolves stubborn dirt, oil, fat and adhesive residue and lets you easily remove. Leaves a nourishing protective layer. Loosens rusted partsLoosens stuck mechanics and jammed metal parts by infiltrating rust layers to loosen them. WD-40® multifunction product infiltrates and loosens rusted and fixed screws. It penetrates in hinges into the thread and protects against corrosion. WD-40® multifunction product displaces moisture, lubricating and eliminating squeaking. >PRODUCT PERFORMANCE AND FEATURES: Eliminates squeaks Undercuts moisture, resin, tar and dirt Cleans and protects against corrosion Loosens rusted parts Loosens stuck mechanics, rusted bolts and nuts Removes dirt and lubricates all types of tools Silicone, resin and PTFE free >MATERIAL COMPATIBILITY: GENERAL: Virtually all materials react to WD-40® Multifunction Product in the same way as they do to other high-quality aliphatic solution benzenes under the same conditions of exposure, such as spraying, short or even prolonged immersion. WD-40® multifunction product does not contain silicone, PTFE or chlorofluorocarbons. RUBBER: No visible effects on the surface of various types of rubber that have been sprayed with WD-40® Multifunction Product. Certain types of rubber swell when immersed in WD-40® Multifunction Product for extended periods of time. STRENGTHENED STEEL (for hydrogen embrittlement): Rated SAFE according to the Lawrence Hydrogen Effusion Test. FABRIC:WD-40® multi-function product causes no visible effect except slight discoloration that can be easily removed with naphtha or dry cleaning solvent (Tested: Nylon, Orlon, Wool, Dralon, Cotton). PAINTED SURFACES: Many types of paint on various surfaces have been exposed to WD-40® Multifunction Product without observing an effect. Wax polishes and certain wax coatings may be softened by WD-40® Multifunction Product. PLASTICS: Die folgenden Kunststoffe wurden 168 Stunden lang in WD-40® Multifunktionsprodukt eingetaucht ohne sichtbaren Effekt: The following plastics have been immersed in WD-40® Multifunction Product for 168 hours with no visible effect: polyethylene - Formica - epoxy - Delrin - polypropylene - acrylic - vinyl - polyester - nylon. Clear polycarbonate and polystyrene may develop hairline cracks or larger cracks when in contact with WD-40® multifunction product. > APPLICATION: Shake well before use. Hold can upright, tilted or upside down when spraying. IMPORTANT: Disconnect power from power tools, equipment and other live parts before spraying.

WD-40 SPECIALIST contact spray removes oil, dirt, flux and oxidation residues from sensitive electrical or electronic equipment. The product can be used on electrical equipment, contacts, plastic and rubber.Temperature application range: room temperatureApplication:First disconnect all plugs from equipment to avoid current and allow hot surfaces to cool. Shake the can before use and apply the spray directly on the surface to be treated at a distance of 15 to 20 cm. This will remove any residue that could interfere with electrical contact. Tilt the surface while cleaning and allow excess liquid to dry completely before restoring power. To avoid accidental damage, always check the manufacturer's instructions before applying the product to the equipment. Do not spray product into cavities, openings, crevices or areas of your device where it does not have sufficient airflow to support complete evaporation.Smart Straw - Product Benefits:The integrated spray head allows you to switch between large-area and precise spraying. In this case, the tube remains firmly attached to the spray head and is therefore no longer lost during application. For area spraying, the spray tube is simply folded down. With the spray tube folded out, you can reach small spaces and apply the product there with pinpoint accuracy. The 360° valve allows the can to be held upright or even overhead, making any application possible.WD-40® multifunctional product infiltrates and loosens rusted and stuck screws. It penetrates the threads of hinges and protects against corrosion. WD-40® multifunction product displaces moisture, lubricates and eliminates squeaks. > PRODUCT PERFORMANCE AND FEATURES: Smart Straw® Spray system for area and spot spraying Fast acting and non-conductive Perfect cleaning for electrical/electronic equipment, contacts, plastics or rubber Penetrates quickly without leaving residues Penetrates even the most difficult to reach areas K2 registered #145372 > AREAS OF APPLICATION: Electrical assembly Circuit boards Controls Printers & copiers Switches > USAGE: Shut off unit and allow hot surfaces to cool. Disconnect all plugs from unit to avoid power supply. Shake can before use. Apply spray directly to surface to be treated at a distance of 15 to 20cm to remove all residues that may interfere with electrical contact. Tilt surface during cleaning. Allow excess liquid to dry completely before restoring power. To avoid accidental damage, always check manufacturer's instructions before applying product to equipment. Do not spray into cavities, openings, crevices or areas of your equipment where this product does not have sufficient airflow to support complete evaporation. Tilt the surface during cleaning to allow excess liquid to drain and the product to dry completely before returning it to service and connecting it to the electrical circuit.

Moisture Displacing LubricantMulti Spray 1000 is a strong moisture displacing lubricant that loosens stuck parts and protects against corrosion. Multi Spray 1000 displaces moisture by penetrating between the substrate and water and then protecting the substrate like a protective film. The product is ideal for numerous applications in the RC hobby.It is ideal as a lubricant for bearing bushings, shafts, Bowden cables, etc., as well as for impregnating rubber. Multi Spray 1000 keeps rubber and plastic parts supple and smooth and protects plastic parts from weathering. Even already weathered plastic looks like new again due to the high penetrating power of the product. Multi Spray 1000 gives the plastic a natural shine in the process.Multi Spray 1000 cleans and protects tools, work surfaces, engines, sports equipment, boats, weapons, machines and stainless steel, copper or brass surfaces for a long time, but is also particularly suitable for electrical hand tools, switch boxes, power sockets, ignitions, batteries, spark plugs and electrical connections. These are often located in places exposed to weather, dirt, grease and road salt. Multi Spray 1000 has a protective effect, preventing corrosion.Multi Spray 1000 is one hundred percent silicone-free and therefore also an ideal working aid in repair shops and paint stores, or in any place where paints are processed industrially. All these properties make the product the perfect (light) lubricant, cleaner and protector for any work in the workshop. Multi Spray 1000 is available as a user-friendly spray can with extra nozzle and tube for those hard to reach places. HIGHLIGHTS. Loosens stuck parts and protects against corrosion. Keeps rubber and plastic supple and smooth Cleans and protects for a long time. Silicone free! Displaces moisture Ideal lubricant for locks, tools, cables etc.  Schützt elektrische Verbindungen auf sehr lange Daue  OEM-Genehmigung CONTENT base: mineral oil with special additives Density: 718 kg / m³ Consistency: liquid (ready to spray in the aerosol can) viscosity: 17.5 mPa.s (at 50 ° C) Flash point: 0 ° C compressive strength: minimal temperature resistance: -20 ° C to + 120 ° C water resistance: good against condensing moisture, moderately against sprayed water li> Acid Resistance: Good for sour haze, moderately against sour fluids no rust after 1000 hours (steel plates in relative humidity of 95%) no rust after 50 hours of salt spray test, starting rust after 100 hours Penetrating power: good Lubricant content: 25% Tests: Meets NSF requirements for category H2, registration number: 153349. Application conditions: -20°C to +40°C Substrate: All ferrous and non-ferrous metals, rubber and many plastics (except PMMA, PC, PTFE) USAGEPreparation of the substrate: Provide a clean, dry, grease-free and non-corroded substrate.Shake spray can well before use. When used as a lubricant, spray the product directly onto the part to be lubricated. When used as a plastic and rubber protector, spray the product directly (spray distance 15-20 cm) or apply with a cloth or sponge. To achieve a beautiful shine, briefly polish the plastic with a clean, dry Multi Wipe. Material cleaning: With Innotec Multisol or Innotec Power Clean Hand cleaning: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water Shelf life: 2 years in unopened original packaging.

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

Genuine Motul spare/option part. High-cling oil for foam cartridge air filters, especially for offroad and street use. The oil reinforces the the air filter'e efficiency and retains dirt, mud and sand particles, which will greatly extend the life of the engine. The blue tint makes it easier to control even oil application to the filter.Apply oil to filter generously and work the foam vigorously by hand to ensure complete oil penetration. Press foam slightly to remove excessive oil when done.Contents:1 piece / 400 ml

6 litre gas can with thumb activated filler valve.With Rapido filling up is quicker, simpler and more convenient than ever! Thanks to the dosing button you can control the flow of fuel precisely.Unlock by folding out!Press the button and keep control of filling!Lock by folding in again. Finished!No spills, no awkward handling, all clean and easy Other:Half round spout for ventilation and visibility suitable also for the smallest tank openingsLarge opening for easy fillingFlow controlled by press-buttonVentilation allows full flowSturdy design with two handlesTransparent 6 litre container with litre indication in the filling and rest positionsContents:1 piece

If you want a special combination of compounds please enter that information into the "note to us" form field at the end of the checkout process.Mammoth Supergrip for 1/6 and 1/5 offroad cars. Fits too for Formular 1 models!Parking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURTotal Price                                                                                            85,80 EUR    105,70 EUR = 191,50 EUR SETTotal for 1 pair each front and rear: 169,90 EUR================================Also suitable for:With the following wheel adapter: y1183 Rim adapter

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

Ideal work stand with extra wide tripod up to 100 kg. load capacity with excellent stability, even on uneven (!) urface.Specially made support mechanism, individually adjustable width from 115 mm to 375 mm for most RC cars from 1/10 to 1/5 scale. incline from 0 to 90° Quickly folded and loaded For easy storage, as well as for transport completely foldable! (Carrying bag available!)Height adjustment of the support from 635 mm to 1000 mm and inclination from 0-90° Length of the support surface 386 mm Bis zu 100Kg belastbar! Support mechanism continuosly adjustable in width Due to various adjustment options, the Top Tuning CAR STAND offers the optimal possibilities for making adjustments or maintenance work on the RC car. The load capacity and stability are beyond doubt with a load limit of 100 kg and the extremely stable tripod. The up to 90 ° adjustable slant shows your RC car at events and presentations, as well as in your assembly room to its best advantage! 6.5 kg. weight Pivoting bracket Height adjustable from 69 to 104 cm Basic frame is made of steel, painted or chromed Car bracket is made of aluminum and stainless steel A tool holder TT1030/01 is also available as an accessory in our shop selection.

Genuine FG spare/option part.Measures:Width: 111 mmHeight: 47 mmDepth: 23 mmContents:1 piece