6407/05 FG Mini pin M / OR tires, glued, white, 2 pcs.

Spare part for the Leopard 2010 2WD/4WD versionMeasures:Diameter: 160 mmWidth: 64 mmsquae 18mmThe Mini Block tires are developed for slightly loose underground. They are excellent as front tire for the 2WD models in connection with the Mini Pin tires on the rear axle. The tires are glued ready to run on the widened 1:6 wheels.These wheels are suitable for the FG Marder, Beetle, Off-Road Buggy and the monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.

Glued on robust 6-spoke star wheels, with 6 ribbed reinforcement bars.With 18 mm wheel square, suitable for most 1:5 / 1:6 RC cars, FG, Carson, etc.Lane widening with 23 mm countersunk nut and 14 mm deep square drive for most models.450 block sections 3.5 mm thick, provide a good grip, even on hard or slippery surfaces.Due to the high-strength 14 mm tire shoulder, the cornering power of the Rallye-Cross 450 is high, despite the high profile of 3.5 mm, but without provoking a disproportionate overdrive of the model.The large inner diameter of 114 mm the rim, as well as the position of the wheel allows on nearly all models to eventually mount a disc brake at the front, as well as rear wheels. The dimension of the inside edge of the rim to the wheel is 20 mm. The 18 mm, 6-braced wheel square of the Rallye-Cross 450 rim is 8 mm deep.Measures of the Rallye-Cross 450 wheel/rim:Outside diameter: 162 mmProfile width: 62 mmRim inside: 114 mmTire shoulder: 14 mmBlock profile: 3,5 mmAlso suitable for:With the following wheel adapter: y1183 Rim adapterWith the following wheel adapter: y0786 Rim adapter

Narrow Off-Road Buggy tires 60 mm, ready glued on rims. Suitable for all 1:6 Off-Road Buggies. To mount them on FG Off-Road models you need the 18 mm square wheel driver y0067. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing () if necessary is unavoidable.Diameter: 180 mmWidth: 60 mmContents:2 pieces

Item N° 67214/05 Mini block M / OR tires, glued, white, 2pcs.Completely new revised and in important details improved Mini Block Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant.The FG Mini Block tires are especially well-suited for slightly loose and humid ground. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. The Mini Block tires are also well-suited as front tires for 2WD models in combination with the Mini Pin tires on the rear axle. The tires are ready glued on the new Leo 1:6 wheels. For the assembly you need the 12mm square wheel drivers (ItemN°. 06107/07).The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models.

Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available  with 24mm hex for Losi, HPI Baja 5 and Carson GP Wild Attack series cars and they allready glued!To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims or for Losi and HPI models: y1406/01 - Big Digger y1407/01 - Cross Bond y1408/01- Over Lander y1409/01 - Giant Grip y1417/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.24 mm hex for Losi, HPI Baja 5 cars.Contents:2 pieces / 1 pair

The electric powered version of the legendary Marder buggy is equipped with a powerful 1400kV brushless motor. Power supply: 4S Li-Po battery pack. In its entry level version 4S, the running time is about 15 minutes with lightning-accelerations and a top speed superior to the gas powered Marder one. In the 4S configuration, the E-Marder is a true rocket ship!You can select the car with complete RTR-equipment from the options menu. RTR equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. In the first place our 1:6 Off-Road Buggy stands for driving fun. Through the knobbed tires or with Slick tires (optional extras) the model can be driven cross-country, on a car park, simply just everywhere.The RTR version of the car includes servo, transmitter, receiver, transmitter / receiver and rechargeable batteries. 2WD Off Road BuggyMachined 4 mm aluminum chassis plate with side guardsIndependent suspension with many options for adjustmentRoll cage, can be used as a carrying handle as wellClosed factory painted body shell with decals already appliedFlange rims with knobby tiresBrushless motor150A brushless ESCTwo locations for the batteries with hook-and-loop strapsDimensions:Length: 620 mmWidth: 420 mmHeight: 260 mmWheelbase: 470 mmWeight: 6,4 kgContents:1 piece